Black & Decker 395136-00 instruction manual Additional Safety Rules For Miter Saws

Page 8

395136-00,03,BT1500 6/22/04 9:05 AM Page 8

DON’T OVERREACH. Keep proper footing and balance at all times.

MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for best and safest performance. Follow instructions for lubricating and changing accessories.

DISCONNECT TOOLS before servicing; when changing accessories, such as blades, bits, cutters, and the like.

REDUCE THE RISK OF UNINTENTIONAL STARTING. Make sure switch is in OFF position before plugging in.

USE RECOMMENDED ACCESSORIES. Consult the instruction manual for recommended accessories. The use of improper accessories may cause risk of injury to persons.

NEVER STAND ON TOOL. Serious injury could occur if the tool is tipped or if the cutting tool is unintentionally contacted.

CHECK DAMAGED PARTS. Before further use of the tool, a guard or other part that is damaged should be carefully checked to determine that it will operate properly and perform its intended function—check for alignment of moving parts, binding of moving parts, breakage of parts, mounting and any other conditions that may affect its operation. A guard or other part that is damaged should be properly repaired or replaced. Do not use tool if switch does not turn it on and off.

NEVER LEAVE TOOL RUNNING UNATTENDED. TURN POWER OFF. Don’t leave tool until it comes to a complete stop.

D O N O T O P E R AT E E L E C T R I C TO O L S N E A R F L A M M A B L E L I Q U I D S O R I N G A S E O U S O R EXPLOSIVE ATMOSPHERES. Motors in these tools may spark and ignite fumes.

If you have any questions, call 1-800-54-HOW-TO

USE PROPER EXTENSION CORDS. Make sure your extension cord is in good condition. When using an extension cord, be sure to use one heavy enough to carry the current your product will draw. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating. The following table shows the correct size to use depending on cord length and nameplate ampere rating. If in doubt, use the next heavier gage. The smaller the gage number, the heavier the cord.

 

 

 

Minimum Gage for Cord Sets

 

Volts

 

 

Total Length of Cord in Feet

120V

 

25

26-50

51-100

101-150

240V

 

50

51-100

101-200

201-300

Ampere Rating

 

American Wire Gage

 

More

 

Not more

 

Than

 

Than

 

 

 

 

0

-

6

18

16

16

14

6

-

10

18

16

14

12

10

-

12

16

16

14

12

12

-

16

14

12

Not Recommended

Additional Safety Rules For Miter Saws

CAUTION: FAILURE TO HEED THESE WARNINGS MAY RESULT IN PERSONAL INJURY AND SERIOUS DAMAGE TO THE SAW.

DO-Protect electric supply line with at least a 15 ampere time-delay fuse or a circuit breaker.

DO-Make certain the blade rotates in the correct direction and that the teeth at the bottom of the blade are pointing to the rear of the miter saw.

DO-Be sure all clamp handles are tight before starting any operation.

8

Image 8
Contents HOW-TO Parts Description Figures 1,2 Operating Handle 31.6 22.5 395136-00,03,BT1500 6/22/04 904 AM 31.6 Work Extensions Stop Block Extensiones Bloque DE Tope Important Safety Instructions Safety Warnings Double InsulationSafety Instructions Polarized Plugs Safety Instructions For All ToolsAdditional Safety Rules For Miter Saws 395136-00,03,BT1500 6/22/04 905 AM On Guard Danger Keep Away from BLADE. Danger Electrical ConnectionUnpacking Your Saw Specifications Installing a New Saw BladeFamiliarization Bench MountingAssembling and Adjusting Your Saw Adjustments Attaching Work ExtensionsAttaching Dust BAG Attaching Stop BlockMiter Pointer Adjustment Bevel Pointers Bevel Stop AdjustmentFence Adjustment Turn Off and Unplug the Miter SawBrushes OperationCrosscuts Bevel CutsQuality of CUT Clamping the WorkpiecePretesting with Scrap Material is Extremely Important Cutting Trim Molding and Other FramesCutting Compound Miters Cutting Crown MoldingBowed Material Bevel Setting Type of CUTAluminum Cutting Carbide Tipped Blade only Trouble Shooting Guide MaintenancePerform all maintenance with miter saw unplugged Be Sure to Follow Safety Rules and InstructionsAccessories Service InformationFull Two-Year Home Use Warranty Description des pièces figures 1 et NO. BT1500Consignes de sécurité importantes Consignes de sécurité double isolationConsignes de sécurité fiches polarisées Consignes de sécurité tous les outilsConsignes de sécurité additionnelles scie à onglets SUR LA Plaque DE Retenue DU Dispositif DE Protection Raccordement électriqueMontage sur un établi Déballage de la scieFamiliarisation Installation d’une lame neuve Fixation du sac à poussièreFixation de la butée Fixation des rallongesArrêter ET Débrancher LA Scie À Onglets Visibilité et déclenchement du protège-lame Balais Débrancher la fiche de la prise muraleFonctionnement InterrupteurMéthode de coupe Coupes en biseauQualité de la coupe Position du corps et des mains figureCoupe À Onglets Combinée Fixation de l’ouvrage Arrêter et débrancher la scieSupport de longs ouvrages Arrêter et débrancher la scie Coupe DE Moulures EN Couronne Biseau Coupe Côté GAUCHE, Coin IntérieurCoupes particulières Coupe de l’aluminiumGuide de dépannage Garantie Complète DE Deux ANS Pour L’USAGE Domestique Renseignements Concernant LE ServiceRemplacement Gratuit DE L’ÉTIQUETTE ’AVERTISSEMENT Instrucciones importantes de seguridad Advertencias de seguridad Doble aislamientoAdvertencias de seguridad Clavijas polarizadas Siempre Utilice Anteojos DE SEGURIDAD. También utiliceSe haya detenido completamente EN LA Carcaza DEL Motor EN LA Guia Movil Siempre Ajuste LA GuiaEN LA Guarda Peligro Alejese DE EL Disco EN LA Placa DE Retención DEL ProtectorInstalación de un disco nuevo Capacidad DE CorteEnsamblaje y ajuste de su sierra Instalación de la bolsa para polvoInstalación del tope Instalación de las extensiones de trabajoDesconectada Ajuste DE LA Escala DE IngleteAjuste DEL Indicador DE Inglete Ajuste DEL Tope DE BiselCarbones OperaciónCortes DE Bisel Calidad DEL CortePosicion DE Cuerpo Y Manos Vease Figura Sujecion DE LA Pieza DE TrabajoSoporte Para Piezas Largas Corte DE MARCOS, CAJAS, Y Otros Proyectos DE Cuatro LadosCorte DE Molduras Y Otros Marcos Corte DE Inglete CompuestoCorte DE Aluminio Corte DE Molduras DE RemateAjuste DE Bisel Tipo DE Corte Guía para la solución de problemas frecuentes MantenimientoCorte DE Tuberia DE Plástico ImportanteInformacion Respecto EL Servicio Garantia Para USO Doméstico POR DOS Años CompletosCULIACAN, SIN MEXICO, D.FMERIDA, YUC MONTERREY, N.L395136-00,03,BT1500 6/22/04 905 AM 395136-00,03,BT1500 6/22/04 905 AM