Delta N081935, 18-900L Additional Specific Safety Rules, Additional Safety Rules for the Lasers

ADDITIONAL SPECIFIC SAFETY RULES

FAILURE TO FOLLOW THESE RULES MAY RESULT IN SERIOUS INJURY.

1.	DO NOT OPERATE THIS MACHINE until it is completely	14. KEEP ARMS, HANDS, AND FINGERS away from the bit.
	assembled and installed according to the instructions. A		Serious injury to the hand can occur.
	machine incorrectly assembled can cause serious injury.	15. HOLD THE WORKPIECE FIRMLY AGAINST THE
2.	OBTAIN ADVICE from your supervisor, instructor, or		TABLE. Do not attempt to drill a workpiece that does
	another qualified person if you are not thoroughly familiar		not have a flat surface against the table, or that is not
	with the operation of this machine. Knowledge is safety.		secured by a vise. Prevent the workpiece from rotating by
3.	FOLLOW ALL WIRING CODES and recommended electrical		clamping it to the table or by securing it against the drill
	connections to prevent shock or electrocution.		press column. Loss of control of the workpiece can cause
4.	SECURE THE MACHINE TO A SUPPORTING SURFACE.		serious injury.
	Vibration can cause the machine to slide, walk, or tip over.	16.	TURN THE MACHINE “OFF” AND WAIT FOR THE DRILL
5.	NEVER START THE MACHINE BEFORE CLEARING		BIT, CUTTING TOOL, OR SANDING DRUM TO STOP
	THE TABLE OF ALL OBJECTS (tools, scrap pieces, etc.).		TURNING prior to cleaning the work area, removing
	Debris can be thrown at high speed.		debris, removing or securing work-piece, or changing
6.	NEVER START THE MACHINE with the drill bit, cutting		the angle of the table. A moving drill bit, cutting tool, or
			sanding drum can cause serious injury.
	tool, or sanding drum against the workpiece. Loss of
		17.	PROPERLY SUPPORT LONG OR WIDE work-pieces.
	control of the workpiece can cause serious injury.
7.	PROPERLY LOCK THE DRILL BIT, CUTTING TOOL, OR		Loss of control of the workpiece can cause severe injury.
		18.	DO NOT PLACE more than 250 pounds of weight on the
	SANDING DRUM IN THE CHUCK before operating this
	machine.		table.
8.	REMOVE THE CHUCK KEY BEFORE STARTING THE	19.	NEVER PERFORM LAYOUT, ASSEMBLY OR SET-UP
	MACHINE. The chuck key can be thrown out at a high		WORK on the table/work area when the machine is
	speed.		running. Serious injury can result.
9.	TIGHTEN ALL LOCK HANDLES before starting the machine.	20.	TURN THE MACHINE “OFF”, disconnect the machine
	Loss of control of the workpiece can cause serious injury.		from the power source, and clean the table/work area
10.	USE ONLY DRILL BITS, CUTTING TOOLS, SANDING		before leaving the machine. LOCK THE SWITCH IN THE
			“OFF” POSITION to prevent unauthorized use. Someone
	DRUMS, OR OTHER ACCESSORIES with shank size
			else might accidentally start the machine and cause
	recommended in your instruction manual. The wrong
			serious injury to themselves.
	size accessory can cause damage to the machine and/or
		21.	ADDITIONAL INFORMATION regarding the safe and
	serious injury.
11.	USE ONLY DRILL BITS, CUTTING TOOLS, OR		proper operation of power tools (i.e. a safety video)
			is available from the Power Tool Institute, 1300
	SANDING DRUMS that are not damaged. Damaged
			Sumner Avenue, Cleveland, OH 44115-2851 (www.
	items can cause malfunctions that lead to injuries.
			powertoolinstitute.com). Information is also available
12. USE RECOMMENDED SPEEDS for all operations. Other
			from the National Safety Council, 1121 Spring Lake
	speeds may cause the machine to malfunction causing
			Drive, Itasca, IL 60143-3201. Please refer to the
	damage to the machine and/or serious injury.
			American National Standards Institute ANSI 01.1 Safety
13.	AVOID AWKWARD OPERATIONS AND HAND
			Requirements for Woodworking Machines and the
	POSITIONS. A sudden slip could cause a hand to move		U.S. Department of Labor OSHA 1910.213 Regulations.
	into the bit.

SAVE THESE INSTRUCTIONS.

Refer to them often and use them to instruct others.

ADDITIONAL SAFETY RULES FOR THE LASERS

SAFETY INSTRUCTIONS FOR LASERS

Read and understand all instructions. Failure to follow all instructions listed below may result in electric shock, fire and/or serious personal injury.

For your own safety, read the tool instruction manual before using any accessory. Failure to heed these warn- ings may result in personal injury and serious damage to the tool and the accessory. When servicing this tool, use only identi- cal replacement parts.

LASER RADIATION EXPOSURE. Do not disassemble or modify the laser. There are no user serviceable parts inside. Serious eye injury could result.

HAZARDOUS RADIATION. Use or modification of the tool for anything other than its designed purpose may result in hazardous radiation exposure.

•Do not operate the laser in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust. Power tools cre- ate sparks which may ignite the dust or fumes.

•Store idle laser out of reach of children and other untrained persons. Lasers are dangerous in the hands of untrained users.

•Tool service must be performed only by qualified repair personnel. Service or maintenance performed by unqualified personnel may result in injury. To locate your nearest DELTA service center call 1-800-223-7278 or go to www.deltaportercable.com on the Internet.

•Do not use optical tools such as a telescope or transit to view the laser beam. Serious eye injury could result.

•Do not stare into beam aperture, or into a reflection from a mirror-like surface

•Do not place the laser in a position which may cause anyone to intentionally or unintentionally stare into the laser beam. Serious eye injury could result.

•Turn the laser off when it is not in use. Leaving the laser on increases the risk of staring into the laser beam.

•Do not disassemble the laser or laser power supply. There are no user serviceable parts inside.

•Do not modify the laser in any way. Modifying the tool may result in Hazardous Laser Radiation Exposure.

•Do not operate the laser around children or allow children to operate the laser. Serious eye injury may result.

•Do not remove or deface warning labels. Removing labels increases the risk of exposure to radiation.

4