Bostitch BTFP02028 owner manual Installation, Assembly, Accessories

Page 8

Regulator

The regulator (D) controls the air pressure shown on the Regulated Pressure Gauge (C). Turn knob clock- wise to increase pressure and counterclockwise to C decrease pressure. When the desired pressure is reached turn collar under knob against knob to lock

in place. The regulated pressure range is 7–150 psi.

Risk of Bursting. Too much air pres-

 

 

sure causes a hazardous risk of bursting. Check the

 

 

manufacturer’s maximum pressure rating for air tools

 

 

and accessories.

Knob

D

The regulator outlet pressure setting must never

 

exceed the maximum pressure rating of the tool or accessory.

Universal Quick Connect BodY

Lock Collar

The universal Quick Connect body (E) accepts the three most popular styles of Quick Connect

(E)plugs: Industrial, automotive, and ARO. One hand push-to-connect operation makes connections simple and easy.

Drain Valve

The drain valve (H) is located at the base of the air tank and is used to drain condensation at the end of each use. See Draining Air Tank under Maintenance.

Cooling System (NOT SHOWN)

This compressor contains an advanced design cooling system. It is normal for this fan to blow air through the vent holes in large amounts. The cooling system is working when air is expelled.

Air Compressor Pump

The pump compresses air into the air tank. Working air is not available until the compressor has raised the air tank pressure above that required at the air outlet.

AIR INTAKE FILTER

The filter (J) is designed to clean air entering the pump. To ensure the pump continually receives a clean, cool, and dry air supply the filter must always be clean and the filter intake must be free from obstructions.

Motor Overload Protector (NOT SHOWN)

The motor has a thermal overload protector. If the motor overheats for any reason, the overload protector will shut off the motor. The motor must be allowed to cool down before restarting.

To restart:

1.Set the On/Off (A) lever to Off and unplug unit.

2.Allow the motor to cool.

3.Plug the power cord into the correct branch circuit receptacle.

4.Set the On/Off (A) lever to ON position.

INSTALLATION

Assembly

You must assemble the compressor before using it for the first time.

Fitting the wheels

•Fit the supplied wheels as shown in figures 5:

•Fig. 5a & 5b: Assembly of wheel kit. Tighten securely.

•Fig. 5c: Assembly of bumper

8

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Guide Dutilisation Manual DE Instrucciones BTFP02028Important Safety Introduction Definitions Safety GuidelinesHow to prevent it What can happenHow to prevent it Attachments & accessoriesWhat can happen Risk to Breathing AsphyxiationAlways wear certified safety equipment TiresRisk of Electrical Shock Risk from Flying Objects Can Happen How to prevent it Risk of Hot surfaces Risk from Moving Parts Risk of Unsafe OperationSpecifications Features FIG Save These Instructions for Future USEInstallation AssemblyAccessories Fit the supplied wheels as shown in figuresInstalling Hoses Disconnecting HosesGrounding Instructions Fig Do not USE AN AdapterExtension Cords Voltage and Circuit ProtectionCompatibility Location Product.10Operating Procedures Pre-Start Checklist FigPreparation For Use Start-up FigMaintenance Maintenance ChartChecking Safety Valve Procedure Daily Weekly See tankAccessories Service InformationFull One Year Warranty Checking Air Filter Element FigGlossary Troubleshooting GuideProblem Code Troubleshooting Codes Code possible cause Can rupture or explodePossible Solution Introduction Importante À LA SécuritéDéfinitions lignes directrices en matière de sécurité Conserver ces directivesCe qui peut se produire Comment l’Éviter Accessoires Risque d’Éclatement Ce qui peut se produire Comment l’Éviter Ce qui peut se produire Comment l’ÉviterRisque de choc Électrique Son utilisation Risque associÉ aux piÈces mobilesRisque associÉ au bruit Ce qui peut se produire Risque DE ChuteCE QUI Peut SE Produire Comment L’ÉVITER Fiche technique ModèlePoids HauteurComposants Fig CaractÉristiquesDépasser la Risque DE RUPTURE. UneDair provoque un dangereux ’UTILISEZ PAS UN Adaptateur AssemblageDirectives relatives à la mise à la terre Fig Emplacement RallongesProtection de la tension et du circuit CompatibilitéMode d’emploi Procédures de fonctionnementListe de vérification de pré-démarrage Fig Démarrage FigEntretien Arrêt FigProgramme d’entretien ProcédureVérification des éléments du filtre d’air Fig Vérification de la soupape de sûretéVidange du réservoir d’air Fig Accessoires Information sur les réparationsRéparations Garantie complète d’un 1 anGlossaire Guide de dépannageCodes de dépannage Cause probable ProblèmeSolution Probable Possibilité d’un moteur Pièces internes du moteurVapeurs inflammables Fusible grillé, disjoncteurInstrucciones Importantes DE Seguridad Definiciones Normas de seguridadGuarde estas instrucciones Riesgo de explosión o incendio ¿Qué puede suceder?Riesgo de explosión ¿Qué puede suceder? Cómo evitarloModificaciones o intento de reparación del tanque de aire Elementos y accesoriosGraves NeumáticosRiesgo de objetos despedidos ¿Qué puede suceder? Riesgo por piezas móviles Cómo evitarloRiesgo DE Caídas Especificaciones Riesgo por ruidos Cómo evitarloComponentes Fig Características FigEn la presión del aire causa un peligroso riesgo Instalación EnsamblajeDebe ensamblar el compresor antes de usarlo por primera vez Coloque las ruedas provistas como se muestra en la figuraCables prolongadores Voltaje y protección del circuitoCompatibilidad LugarPreparación Para EL USO Lista DE Control Previa a LA Puesta EN Marcha FIGGuarde el compresor en posición horizontal o vertical Voltaje y protección del circuito en la sección InstalaciónProcedimientos Operativos MantenimientoPuesta EN Marcha FIG Apagado FIGTabla DE Mantenimiento ProcedimientoControlar LA Válvula DE Seguridad FIG Drenar EL Tanque DE Aire FIGAccesorio Información DEL Servicio TécnicoControlar EL Elemento DEL Filtro DE Aire FIG ReparacionesGarantía completa de un año CULIACAN, SINGUADALAJARA, JAL MEXICO, D.FGlosario CGuía de detección de problema Códigos de detección de problemasCódigo Código Causa posibleGrande para el RestringidaPérdidas de aire Ajuste las conexiones El regulador está DañadoMarch
Top Page Image Contents