Bostitch BTFP02028 Checking Air Filter Element Fig, Accessories, Service Information, Repairs

Page 13

some conditions and duration of use, noise from this product may contribute to hearing loss.

NOTE: All compressed air systems generate condensate that accumulates in any drain point (e.g. tanks, filter, aftercoolers, dryers). This condensate contains lubricating oil and/or

substances which may be regulated and must be disposed of in accordance with local, state, and federal laws and regulations.

Risk of bursting. Drain air tank daily. Water will condense in air tank. If not drained, water will corrode and weaken the air tank causing a risk of air tank rupture.

Risk of Property Damage. Drain water from air tank may contain oil and rust, which can cause stains.

1.Ensure On/Off (A) switch is in the OFF position.

2.Place a suitable container under the drain valve (H) to catch discharge.

3.Grasp lever on drain valve.

4.Slowly rotate lever to gradually bleed air from air tank.

5.When Air Tank Pressure Gauge (B) reads 10 psi, rotate valve to the fully open position.

6.Tip tank back to fully drain water.

7.Close drain valve when finished.

Checking Air Filter Element (Fig. 1)

Hot surfaces. Risk of burn. Outlet tube, pump head, and surrounding parts are very hot, do not touch. Allow compressor to cool prior to servicing.

1.Ensure On/Off switch (A) is in the OFF Position.

2.Allow unit to cool.

3.Remove filter cover (J) from base.

4.Remove element from filter base.

5.Place new element back in filter base. Purchase replacement parts from your local dealer or authorized service center. Always use identical replacement parts.

6.Snap filter cover to filter base.

Hot surfaces. Risk of burns. Do not operate without air inlet filter.

Accessories

The use of any other accessory not recommended for use with this tool could be hazardous. Use only accessories rated equal to or higher than the rating of the air compressor.

Recommended accessories for use with your tool are available for purchase from your local dealer or authorized service center. If you need assistance in locating any accessory for your tool, please contact Bostitch Fastening Systems 701 E. Joppa Road Towson, Maryland 21286,call 1-800-556-6696.

Service Information

Please have the following information available for all service calls:

ModelNumber_____________________SerialNumber_______________________________

Date and Place of Purchase ____________________________________________________

Repairs

To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustment should be performed by a BOSTITCH factory service center, a BOSTITCH authorized service center or other qualified service personnel. Always use identical replacement parts.

Full One Year Warranty

BOSTITCH heavy duty industrial tools are warranted for one year from date of purchase. We will repair, without charge, any defects due to faulty materials or workmanship. For warranty repair information, call 1-800-556-6696. This warranty does not apply to accessories or damage caused where repairs have been made or attempted by others. This warranty gives you specific legal rights and you may have other rights which vary in certain states or provinces.

Latin America: This warranty does not apply to products sold in Latin America. For products sold in Latin America, see country specific warranty information contained either in the packaging, call the local company or see website for warranty information.

FREE WARNING LABEL REPLACEMENT (Fig. 4): If your warning labels become illegible or are missing, call 1-800-556-6696 for a free replacement.

13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents BTFP02028 Guide Dutilisation Manual DE InstruccionesDefinitions Safety Guidelines Important Safety IntroductionHow to prevent it What can happenAttachments & accessories How to prevent itWhat can happen Risk to Breathing AsphyxiationTires Always wear certified safety equipmentRisk of Electrical Shock Risk from Flying ObjectsRisk of Hot surfaces Can Happen How to prevent itRisk from Moving Parts Risk of Unsafe OperationSpecifications Save These Instructions for Future USE Features FIGAssembly InstallationAccessories Fit the supplied wheels as shown in figuresDisconnecting Hoses Installing HosesGrounding Instructions Fig Do not USE AN AdapterVoltage and Circuit Protection Extension CordsCompatibility Location Product.10Pre-Start Checklist Fig Operating ProceduresPreparation For Use Start-up FigMaintenance Chart MaintenanceChecking Safety Valve Procedure Daily Weekly See tankService Information AccessoriesFull One Year Warranty Checking Air Filter Element FigProblem Code Troubleshooting GuideGlossary Can rupture or explode Troubleshooting Codes Code possible causeIntroduction Importante À LA Sécurité Possible SolutionDéfinitions lignes directrices en matière de sécurité Conserver ces directivesCe qui peut se produire Risque d’Éclatement Accessoires Comment l’Éviter Risque de choc Électrique Ce qui peut se produire Comment l’ÉviterCe qui peut se produire Comment l’Éviter Risque associÉ aux piÈces mobiles Son utilisationCE QUI Peut SE Produire Comment L’ÉVITER Risque DE ChuteRisque associÉ au bruit Ce qui peut se produire Modèle Fiche techniquePoids HauteurCaractÉristiques Composants FigDair provoque un dangereux Risque DE RUPTURE. UneDépasser la Directives relatives à la mise à la terre Fig Assemblage’UTILISEZ PAS UN Adaptateur Rallonges EmplacementProtection de la tension et du circuit CompatibilitéProcédures de fonctionnement Mode d’emploiListe de vérification de pré-démarrage Fig Démarrage FigArrêt Fig EntretienProgramme d’entretien ProcédureVidange du réservoir d’air Fig Vérification de la soupape de sûretéVérification des éléments du filtre d’air Fig Information sur les réparations AccessoiresRéparations Garantie complète d’un 1 anGuide de dépannage GlossaireCodes de dépannage Cause probable ProblèmeSolution Probable Pièces internes du moteur Possibilité d’un moteurVapeurs inflammables Fusible grillé, disjoncteurDefiniciones Normas de seguridad Instrucciones Importantes DE SeguridadGuarde estas instrucciones Riesgo de explosión o incendio ¿Qué puede suceder?¿Qué puede suceder? Cómo evitarlo Riesgo de explosiónElementos y accesorios Modificaciones o intento de reparación del tanque de aireGraves NeumáticosRiesgo por piezas móviles Cómo evitarlo Riesgo de objetos despedidos ¿Qué puede suceder?Riesgo DE Caídas Riesgo por ruidos Cómo evitarlo EspecificacionesCaracterísticas Fig Componentes FigEn la presión del aire causa un peligroso riesgo Ensamblaje InstalaciónDebe ensamblar el compresor antes de usarlo por primera vez Coloque las ruedas provistas como se muestra en la figuraVoltaje y protección del circuito Cables prolongadoresCompatibilidad LugarLista DE Control Previa a LA Puesta EN Marcha FIG Preparación Para EL USOGuarde el compresor en posición horizontal o vertical Voltaje y protección del circuito en la sección InstalaciónMantenimiento Procedimientos OperativosPuesta EN Marcha FIG Apagado FIGProcedimiento Tabla DE MantenimientoControlar LA Válvula DE Seguridad FIG Drenar EL Tanque DE Aire FIGInformación DEL Servicio Técnico AccesorioControlar EL Elemento DEL Filtro DE Aire FIG ReparacionesCULIACAN, SIN Garantía completa de un añoGUADALAJARA, JAL MEXICO, D.FGlosario Códigos de detección de problemas CGuía de detección de problemaCódigo Código Causa posibleRestringida Grande para elPérdidas de aire Ajuste las conexiones El regulador está DañadoMarch
Top Page Image Contents