Husqvarna RG 2112 E manuel dutilisation DOs and DO NOTs

Page 19

SAFETY WARNINGS FOR OPERATION OF THIS MACHINE

WARNINGS

DOs and DO NOTs

WARNING: FAILURE TO COMPLY WITH THESE WARNINGS AND OPERATING INSTRUCTIONS COULD RESULT IN DEATH OR SERIOUS BODILY INJURY.

DO NOT operate this machine unless you have read and understood this operator’s manual.

DO NOT operate this machine without all guards in place.

DO NOT leave this machine unattended while the engine or motor is running.

DO NOT work on this machine while the engine or motor is running.

DO NOT operate this machine when you are tired or fatigued.

DO NOT operate the machine if you are uncertain of how to run the machine.

DO NOT use damaged equipment or tool.

DO NOT touch or try to stop a moving tool with your hand.

DO NOT transport a machine with the tools mounted on the machine.

DO NOT use a tool that has been dropped or damaged

DO NOT touch the tools immediately after use. These tools require several minutes to cool after operation.

DO NOT use damaged or worn accessory disk.

DO NOT allow other persons to be near the machine when starting, refueling, or when the machine is in operation.

DO NOT operate this machine in an enclosed area unless it is properly vented.

DO NOT operate this machine in the vicinity of anything that is flammable. Sparks could cause a fire or an explosion.

DO NOT operate this machine while under the influence of drugs or alcohol.

DO NOT operate this machine with any of the guards removed.

DO NOT operate this machine unless you are specifically trained to do so.

DO NOT start operation of the machine until you have a clear work area and secure footing.

DO NOT use flammable substances, unsecured loads or people as extra weight. Injury to the operator or other persons could result!

DO NOT use flammable, or improper substances to improve the material removal from the work area.

DO NOT operate the machine if unknown substances are on or near the work area.

DO NOT operate the machine before you determine the nature and volatility of any material that will come in contact with the grinding tools used by this machine.

***************************

This machine was designed for certain applications only. DO NOT modify this machine or use for any application other than for which is it was designed. If you have any questions relative to its application, DO NOT use the machine until you have written Husqvarna Construction Products North America and we have advised you.

Husqvarna Construction Products North America

17400 West 119th Street

Olathe, Kansas 66061, USA

19

Image 19
Contents Operator’s manual Page Page Table DES Matières Instructions PáginaPage Page Proposition 65 de Californie Avertissement California Prop 65 WarningAdvertencia Prop 65 de California Advertencia Sobre EL PolvoPage Figures / Figures / Figuras Figures / Figures / Figuras Figures / Figures / Figuras Figures / Figures / Figuras Parts Identification Identification des pièces Identificación de las piezas Do not USE the Tool DOs and DO NOTsDOs and DO NOTs Options Feature ModelLength cm Description Dimensions NoteAttachment Tool Application GuideMaterial Hour Operation Check List With Machine Cold and Setting LevelService Daily Service Every 50 HoursAll Models  FeaturesAssembly Check Before OperatingExtension Cord Size Minimum Electric Motor Plugs & ConnectorsGasoline Model Tool InstallationRear Axle Positions See FIG Tool Height for Axle Positions See FIGDiamond Segment Blocks FIG Grinding Stones See FIGTungsten Carbide Blocks See FIG Multi-Segmented Diamond Disks Q See & FIG Wire Brushes See FIGTool Holding Pad HH Installation Operating InstructionsStopping the Unit Gasoline Models Maintenance Incidents During OperationStopping the Unit Electric Models Start / Stop of Gasoline Models & FIGLubrication Points Engine Oil Change ProcedureWhen Required Belt TensionImportant Advise AccessoriesInstallation of Kit Also See Parts List Items included in kit See DiagramSpare Parts RepairsModel Serial No Date Remarques Notas Mises EN Garde Mises EN Garde Caractéristiques Modèle Remarques Article Longueur po DescriptionOutil Guide d’application d’outilApplication Matériau Montage Entretiens Toutes LES 50 Heures Entretiens QuotidiensTous les modèles  CaractéristiquesAssemblage Vérifier avant utilisationDu sélecteur de tension Tableau Fiches et connecteurs de moteurs électriquesRelever la protection avant a Desserrer les trois Installation d’outilModèles à essence TableauBloc au carbure de tungstène voir la FIG Blocs diamant segmentés FIGDisques scarificateurs , FIG Disque diamant à segments multiples Q voir , FIG Installation du patin porte-outil HHUtilisation Brosses métalliques voir la FIGArrêt DE LA Machine modèles à essence Problèmes en cours d’utilisationArrêt DE LA Machine modèles électriques Démarrage et arrêt des modèles à essenceVidange d’huile EntretienPoints de lubrification Contenance en huile moteur Honda GXV340Articles compris dans le kit AccessoiresInstallation du kit voir également la liste des pièces Conseils importants12. Pièces détachées 11. RéparationsModèle No. de série Date d’achat Remarques Notas Advertencias Advertencias Opciones ModeloNotas Longitud cm DescripciónFijación a la Material Guía de aplicación de la herramientaServicio Cada 50 Horas Servicio DiarioTodos los modelos CaracterísticasMontaje Revisión antes de manejarTabla TablaTamaño DEL Cordón DE Extensión mínimo Altura mínima de la herramienta Instalación de la herramientaModelo de gasolina Posiciones del eje trasero ver FIGBloques de segmentos a diamantados FIG Piedras de pulido ver FIGBloques de carburo de tungsteno ver FIG Instalación del portaherramienta HH Ver , , , , FIG Muelas escarificadoras , FIGCepillos de alambre FIG Discos diamantados de segmentos múltiples , FIGParo DE LA Máquina modelos de gasolina Instrucciones de operaciónIncidentes durante la operación Paro DE LA Máquina modelos eléctricosProcedimiento para cambiar el aceite del motor MantenimientoPuntos de lubricación Capacidad de aceite del motor Honda GXV340Accesorios Consejo importantePiezas incluidas en el kit Piezas incluidas en el kit vea el diagramaInstalación del kit ver también la lista de piezas Piezas de repuesto ReparacionesModelo No. de serie Fecha Remarques Notas Husqvarna South Carolina 542 20 11