Husqvarna RG 2112 E manuel dutilisation Important Advise, Accessories, Items included in kit

Page 31

4)Tighten the Jam Nut [YY] against the Motor / Engine Platform until the Belt Tensioning Drawbolt [UU] is locked in position.

5)Re-tighten the four Capscrews [ZZ] that attach the motor / engine platform [FIG. 3].

9.Important Advise

•When storing for an extended period of time, use a wire brush to remove hard, caked sludge. Clean and thoroughly lubricate moving parts - so the next job the machine is ready for operation.

•Drive belts must be tight. When the belts are loose, power is lost. Replace worn belts without delay!

•Replace noisy bearings immediately! Worn bearings will quickly destroy the tools.

10.Accessories

The following accessories and kits are available for this machine. See the Parts List section of this document for the part number. For additional information contact your local dealer or call our Toll free Customer Service Telephone number shown on the back cover:

•Weight Kit [FIG. 12, FIG. 13]:

a)Items included in kit:

1)Weight Tray [Z] and Weight Tray Attaching Hardware [AA].

2)Removable Weight Box [BB] and Safety Bolts [CC].

3)Nine (9) Steel Weight Bars [DD] totaling

58 Lbs. (26 kg), and Weight Bar Attaching Hardware [EE]. Note: Can hold an additional Nine (9) Weight bars (Sold Separately) for a Total Maximum Weight of 117 Lbs. (53 kg).

b)Installation of Kit (Also See Parts List):

1)Remove the four (4) existing Capscrews installed in the weight tray mounting holes (used to plug the holes in the gearbox).

2)Mount the Weight Tray [Z] using the Weight Tray Attaching Hardware [AA] supplied in the kit (Four Capscrews, Lockwashers, and Washers).

3)Install the Weight Bars [DD] into the Weight Box [BB]. Use the Weight Bar Attaching hardware [EE] to install the Weight Bars inside the Weight Box. Install the Capscrews so that the heads are to the front of the weight box (outside of machine). Place the smaller washers between the larger washers to form a “notch” that will hold the box assembly in place on the machine. Tighten the Locknuts so that the Weight Bars [DD] are held securely in the Weight Box [BB].

4)Lift the assembled Weight Box [BB] onto the Weight Tray [Z] (installed on the machine). Align the Washers so that they fit into the slots in the back of the Weight Tray [Z]. Lower the Weight Box [BB] onto the Weight Tray [Z].

5)Use the Hold-Down Bolts [CC] as a method to hold the Weight Box [BB] securely to the machine. If the Hold-Down Bolts [CC] are not used the Weight Box can be lifted off of the machine, but this is not recommended if the machine is to be used of a rough sur- face, or if the machine is to be lifted into the air for any reason.

WARNING: DO NOT lift the machine into the air unless the Weight Box [BB] is securely fastened to the machine using the Hold-Down Bolts [CC]. The recommended method is to remove the Weight Box [BB] BEFORE lifting the machine. The machine will then remain horizontal when lifted, using the lifting point.

•Water Tank Kit [FIG. 1, FIG. 11, FIG. 31]:

a)Items included in kit (See Diagram 4):

1)Water Tank Assembly [QQ1]. Includes Lid, Water Valve [QQ2], and Hose.

2)Water Tank Bracket [QQ3] and Attaching Hardware.

3)Nozzle Bracket Assembly (Not Shown), and Attaching Hardware.

4)Hose Clamps [QQ4] and Attaching Hardware.

b)Installation of kit (Also See Parts List):

1)Water Tank Assembly [QQ1] comes pre-assembled. Place Water Tank Assembly [QQ1] in frame as shown in FIG. 1. Leave the end of the hose free.

2)Mount the Water Tank Bracket [QQ3] INSIDE of the handle supports (frame) as shown in FIG. 1, FIG 2 and FIG. 3. Using two (2) each of the M8 Capscrews, Lockwashers, Washers included in the kit, secure the Water Tank Bracket [QQ3] in position.

3)See FIG. 31. At the back of the machine, to the right side of the Dust Port [XX] find the Hose Port Cover [AAA]. Using the small end of the Wrench [V] loosen the two (2) M8 Capscrews that hold this cover in position, then rotate it counter-clockwise until the Hose Port

is exposed. Re-tighten the M8 Capscrews until the Hose Port Cover is secured in its lowered position.

4)Move the Axle into the Transport Position [E] [FIG. 11] and tilt the machine backwards until the handles are resting on the ground.

31

Page 30 Page 32
Image 31
Page 30 Page 32
Contents Operator’s manual Page Page Table DES Matières Instructions PáginaPage Page Proposition 65 de Californie Avertissement California Prop 65 WarningAdvertencia Prop 65 de California Advertencia Sobre EL PolvoPage Figures / Figures / Figuras Figures / Figures / Figuras Figures / Figures / Figuras Figures / Figures / Figuras Parts Identification Identification des pièces Identificación de las piezas Do not USE the Tool DOs and DO NOTsDOs and DO NOTs Options Feature ModelLength cm Description Dimensions NoteAttachment Tool Application GuideMaterial Hour Operation Check List With Machine Cold and Setting LevelService Daily Service Every 50 HoursAll Models  FeaturesAssembly Check Before OperatingExtension Cord Size Minimum Electric Motor Plugs & ConnectorsGasoline Model Tool InstallationRear Axle Positions See FIG Tool Height for Axle Positions See FIGDiamond Segment Blocks FIG Grinding Stones See FIGTungsten Carbide Blocks See FIG Multi-Segmented Diamond Disks Q See & FIG Wire Brushes See FIGTool Holding Pad HH Installation Operating InstructionsStopping the Unit Gasoline Models Maintenance Incidents During OperationStopping the Unit Electric Models Start / Stop of Gasoline Models & FIGLubrication Points Engine Oil Change ProcedureWhen Required Belt TensionImportant Advise AccessoriesInstallation of Kit Also See Parts List Items included in kit See DiagramSpare Parts RepairsModel Serial No Date Remarques Notas Mises EN Garde Mises EN Garde Caractéristiques Modèle Remarques Article Longueur po DescriptionOutil Guide d’application d’outilApplication Matériau Montage Entretiens Toutes LES 50 Heures Entretiens QuotidiensTous les modèles  CaractéristiquesAssemblage Vérifier avant utilisationDu sélecteur de tension Tableau Fiches et connecteurs de moteurs électriquesRelever la protection avant a Desserrer les trois Installation d’outilModèles à essence TableauBloc au carbure de tungstène voir la FIG Blocs diamant segmentés FIGDisques scarificateurs , FIG Disque diamant à segments multiples Q voir , FIG Installation du patin porte-outil HHUtilisation Brosses métalliques voir la FIGArrêt DE LA Machine modèles à essence Problèmes en cours d’utilisationArrêt DE LA Machine modèles électriques Démarrage et arrêt des modèles à essenceVidange d’huile EntretienPoints de lubrification Contenance en huile moteur Honda GXV340Articles compris dans le kit AccessoiresInstallation du kit voir également la liste des pièces Conseils importants12. Pièces détachées 11. RéparationsModèle No. de série Date d’achat Remarques Notas Advertencias Advertencias Opciones ModeloNotas Longitud cm DescripciónFijación a la Material Guía de aplicación de la herramientaServicio Cada 50 Horas Servicio DiarioTodos los modelos CaracterísticasMontaje Revisión antes de manejarTabla TablaTamaño DEL Cordón DE Extensión mínimo Altura mínima de la herramienta Instalación de la herramientaModelo de gasolina Posiciones del eje trasero ver FIGBloques de segmentos a diamantados FIG Piedras de pulido ver FIGBloques de carburo de tungsteno ver FIG Instalación del portaherramienta HH Ver , , , , FIG Muelas escarificadoras , FIGCepillos de alambre FIG Discos diamantados de segmentos múltiples , FIGParo DE LA Máquina modelos de gasolina Instrucciones de operaciónIncidentes durante la operación Paro DE LA Máquina modelos eléctricosProcedimiento para cambiar el aceite del motor MantenimientoPuntos de lubricación Capacidad de aceite del motor Honda GXV340Accesorios Consejo importantePiezas incluidas en el kit Piezas incluidas en el kit vea el diagramaInstalación del kit ver también la lista de piezas Piezas de repuesto ReparacionesModelo No. de serie Fecha Remarques Notas Husqvarna South Carolina 542 20 11
Top Page Image Contents