Husqvarna RG 2112 E manuel dutilisation Repairs, Spare Parts, Model Serial No Date

Page 32

5)Under the front of the machine, and in front of the Accessory Disks [P], find and remove the two M8 Capscrews, Lockwashers, and Washers that match the pattern in the Nozzle Bracket Assembly (Not Shown). Remove these Capscrews, Lockwashers, and Washers from the machine. This hardware was used only to plug holes in the gearbox.

6)Using the two (2) M8 Capscrews, Lockwashers, and Washers supplied in the kit, mount the Nozzle Bracket Assembly with the hose barb fitting toward the rear of the machine.

7)Take the free end of the Water Tank Hose and slide a Hose Clamp [QQ4] loosely over the hose. Route the hose through the side of the machine [See FIG. 1] and the opened Dust Port Cover [FIG. 31]. Attach the hose to the Hose Barb fitting on the Nozzle Bracket Assembly.

8)Slide the Hose Clamp down the hose until it is on the Hose Barb fitting at the Nozzle Bracket. Tighten the M6 Capscrew, and Lockwasher that hold the Hose Clamp [QQ4].

9)Install two (2) more Hose Clamps [QQ4] along the frame [See FIG. 1].

10)Make sure the Water Valve [QQ1] is closed before adding any water to the water tank.

WARNING: DO NOT lift the machine into the air if the Water Tank is filled with water. This added weight will cause the balance point to be shifted so that the machine will not lift in a horizontal position.

11. Repairs

We carry out all repairs in the shortest possible time and at the most economical prices. See front cover for our address and telephone numbers.

12. Spare Parts

For a quick supply of spare parts it is essential to quote the data shown on the Serial Number Plate [VV] [See FIG. 13] fixed to the machine. Make note of this infor- mation & the purchase date below, and on the front cover of this document for quick reference:

Model:	Serial No:	Date:
________________	________________	________________

32

Image 32

Contents Operator’s manual Page Page Table DES Matières Página InstructionsPage Page California Prop 65 Warning Proposition 65 de Californie AvertissementAdvertencia Sobre EL Polvo Advertencia Prop 65 de CaliforniaPage Figures / Figures / Figuras Figures / Figures / Figuras Figures / Figures / Figuras Figures / Figures / Figuras Parts Identification Identification des pièces Identificación de las piezas DOs and DO NOTs Do not USE the ToolDOs and DO NOTs Feature Model OptionsDimensions Note Length cm DescriptionMaterial Tool Application GuideAttachment With Machine Cold and Setting Level Service DailyService Every 50 Hours Hour Operation Check List Features AssemblyCheck Before Operating All ModelsElectric Motor Plugs & Connectors Extension Cord Size MinimumTool Installation Rear Axle Positions See FIGTool Height for Axle Positions See FIG Gasoline ModelTungsten Carbide Blocks See FIG Grinding Stones See FIGDiamond Segment Blocks FIG Wire Brushes See FIG Tool Holding Pad HH InstallationOperating Instructions Multi-Segmented Diamond Disks Q See & FIGMaintenance Incidents During Operation Stopping the Unit Electric ModelsStart / Stop of Gasoline Models & FIG Stopping the Unit Gasoline ModelsEngine Oil Change Procedure When RequiredBelt Tension Lubrication PointsAccessories Installation of Kit Also See Parts ListItems included in kit See Diagram Important AdviseModel Serial No Date RepairsSpare Parts Remarques Notas Mises EN Garde Mises EN Garde Caractéristiques Modèle Article Longueur po Description RemarquesApplication Matériau Montage Guide d’application d’outilOutil Entretiens Quotidiens Entretiens Toutes LES 50 Heures Caractéristiques AssemblageVérifier avant utilisation Tous les modèlesTableau Fiches et connecteurs de moteurs électriques Du sélecteur de tensionInstallation d’outil Modèles à essenceTableau Relever la protection avant a Desserrer les troisDisques scarificateurs , FIG Blocs diamant segmentés FIGBloc au carbure de tungstène voir la FIG Installation du patin porte-outil HH UtilisationBrosses métalliques voir la FIG Disque diamant à segments multiples Q voir , FIGProblèmes en cours d’utilisation Arrêt DE LA Machine modèles électriquesDémarrage et arrêt des modèles à essence Arrêt DE LA Machine modèles à essenceEntretien Points de lubrificationContenance en huile moteur Honda GXV340 Vidange d’huileAccessoires Installation du kit voir également la liste des piècesConseils importants Articles compris dans le kitModèle No. de série Date d’achat 11. Réparations12. Pièces détachées Remarques Notas Advertencias Advertencias Modelo OpcionesLongitud cm Descripción NotasGuía de aplicación de la herramienta Fijación a la MaterialServicio Diario Servicio Cada 50 HorasCaracterísticas MontajeRevisión antes de manejar Todos los modelosTamaño DEL Cordón DE Extensión mínimo TablaTabla Instalación de la herramienta Modelo de gasolinaPosiciones del eje trasero ver FIG Altura mínima de la herramientaBloques de carburo de tungsteno ver FIG Piedras de pulido ver FIGBloques de segmentos a diamantados FIG Muelas escarificadoras , FIG Cepillos de alambre FIGDiscos diamantados de segmentos múltiples , FIG Instalación del portaherramienta HH Ver , , , , FIGInstrucciones de operación Incidentes durante la operaciónParo DE LA Máquina modelos eléctricos Paro DE LA Máquina modelos de gasolinaMantenimiento Puntos de lubricaciónCapacidad de aceite del motor Honda GXV340 Procedimiento para cambiar el aceite del motorConsejo importante AccesoriosInstalación del kit ver también la lista de piezas Piezas incluidas en el kit vea el diagramaPiezas incluidas en el kit Modelo No. de serie Fecha ReparacionesPiezas de repuesto Remarques Notas Husqvarna South Carolina 542 20 11