Husqvarna RG 2112 E  Features, Assembly, Check Before Operating, All Models, Electric Models

Page 24

•Mandatory

•Prohibition

•Indication

•Warning Triangle

These signs will give advice for your safety.

Before leaving our factory every machine is thoroughly tested.

Follow our instructions strictly and your machine will give you long service in normal operating conditions.

1.  Features

Use: Surface grinding of concrete or other types of flooring. For repairing horizontal surfaces that have been damaged by the weather, or by improper finishing methods, or that require removal of deteriorated coatings, overlays, or buildups.

Tools:

1)2 x 2 x 4” (50 x 50 x 100 mm) size, Six (6) per unit. In any of the types shown below:

a)Grinding Stones [FIG. 14]

b)Tungsten Carbide Segment Block [FIG. 16].

c)Tungsten Carbide Impregnated Grinding Block (Not Shown)

d)Scarifier Blocks (Star, Beam, TC wheels) [FIG. 27 & FIG. 28].

e)Wire Brushes [FIG. 26].

f)Diamond Blocks [FIG. 15].

2)Multi-Segmented Diamond Disks: Two (2) disks per unit, 10” (250 mm) diameter, 10 or 20 diamond segments on each disk [FIG. 24 & FIG. 25].

3)Tool Holding Pad, with “hook-and-loop” type of tool attachment, holds the following [FIG. 19]:

a)Scrubbing Pad [JJ] [FIG. 19]: Two (2) pads per unit, 10” (250 mm) diameter, Nylon mesh Impregnated with Silicon Carbide.

(For information contact your Dealer)

Depth of Cut (Maximum):

See Section 4 (Tool Installation & Application).

Maximum material Size: N/A

Nominal & Operating Weight: See “Specifications”.

Dimensions, Grinding Width, Spindle Shaft RPM: See “Saw Dimensions”.

Before starting up machine make sure you read these instructions and are familiar with the operation of this machine.

The working area must be completely clear, well lit and all safety hazards removed (no water or dangerous objects in the vicinity).

The operator must wear protective clothing appropriate to the work he is doing.

We recommend hearing, respiratory and eye protection.

Any persons not involved in the work, should leave the area.

Only work on flat horizontal areas. Working on steep slopes or hills could cause the operator to lose control of the machine. This could result in injury or death to the operator or other persons in or near the work area!

2.Assembly

•When unpacked, this unit is fully assembled, except for installation of the grinding “tools”. For tool installation See Section 4 of this document.

•The dealer or end user must do the installation of optional or accessory items, such as a water tank kit.

3. Check Before Operating

All Models:

•Take into account the working conditions from a health and safety point of view.

•For start up refer to the engine, or motor manual.

Electric Models:

The applicable national and local electrical codes and enforcement bodies will be the determining authority on the proper connec- tions and use of this machine. In all cases it

is the operator/owner’s responsibility to ensure that this equipment is in full compliance with these codes.

24

Page 23 Page 25
Image 24
Page 23 Page 25
Contents Operator’s manual Page Page Table DES Matières Página InstructionsPage Page California Prop 65 Warning Proposition 65 de Californie AvertissementAdvertencia Sobre EL Polvo Advertencia Prop 65 de CaliforniaPage Figures / Figures / Figuras Figures / Figures / Figuras Figures / Figures / Figuras Figures / Figures / Figuras Parts Identification Identification des pièces Identificación de las piezas DOs and DO NOTs Do not USE the ToolDOs and DO NOTs Feature Model OptionsDimensions Note Length cm DescriptionTool Application Guide AttachmentMaterial With Machine Cold and Setting Level Service DailyService Every 50 Hours Hour Operation Check List Features AssemblyCheck Before Operating All ModelsElectric Motor Plugs & Connectors Extension Cord Size MinimumTool Installation Rear Axle Positions See FIGTool Height for Axle Positions See FIG Gasoline ModelGrinding Stones See FIG Diamond Segment Blocks FIGTungsten Carbide Blocks See FIG Wire Brushes See FIG Tool Holding Pad HH InstallationOperating Instructions Multi-Segmented Diamond Disks Q See & FIGMaintenance Incidents During Operation Stopping the Unit Electric ModelsStart / Stop of Gasoline Models & FIG Stopping the Unit Gasoline ModelsEngine Oil Change Procedure When RequiredBelt Tension Lubrication PointsAccessories Installation of Kit Also See Parts ListItems included in kit See Diagram Important AdviseRepairs Spare PartsModel Serial No Date Remarques Notas Mises EN Garde Mises EN Garde Caractéristiques Modèle Article Longueur po Description RemarquesGuide d’application d’outil OutilApplication Matériau Montage Entretiens Quotidiens Entretiens Toutes LES 50 Heures Caractéristiques AssemblageVérifier avant utilisation Tous les modèlesTableau Fiches et connecteurs de moteurs électriques Du sélecteur de tensionInstallation d’outil Modèles à essenceTableau Relever la protection avant a Desserrer les troisBlocs diamant segmentés FIG Bloc au carbure de tungstène voir la FIGDisques scarificateurs , FIG Installation du patin porte-outil HH UtilisationBrosses métalliques voir la FIG Disque diamant à segments multiples Q voir , FIGProblèmes en cours d’utilisation Arrêt DE LA Machine modèles électriquesDémarrage et arrêt des modèles à essence Arrêt DE LA Machine modèles à essenceEntretien Points de lubrificationContenance en huile moteur Honda GXV340 Vidange d’huileAccessoires Installation du kit voir également la liste des piècesConseils importants Articles compris dans le kit11. Réparations 12. Pièces détachéesModèle No. de série Date d’achat Remarques Notas Advertencias Advertencias Modelo OpcionesLongitud cm Descripción NotasGuía de aplicación de la herramienta Fijación a la MaterialServicio Diario Servicio Cada 50 HorasCaracterísticas MontajeRevisión antes de manejar Todos los modelosTabla TablaTamaño DEL Cordón DE Extensión mínimo Instalación de la herramienta Modelo de gasolinaPosiciones del eje trasero ver FIG Altura mínima de la herramientaPiedras de pulido ver FIG Bloques de segmentos a diamantados FIGBloques de carburo de tungsteno ver FIG Muelas escarificadoras , FIG Cepillos de alambre FIGDiscos diamantados de segmentos múltiples , FIG Instalación del portaherramienta HH Ver , , , , FIGInstrucciones de operación Incidentes durante la operaciónParo DE LA Máquina modelos eléctricos Paro DE LA Máquina modelos de gasolinaMantenimiento Puntos de lubricaciónCapacidad de aceite del motor Honda GXV340 Procedimiento para cambiar el aceite del motorConsejo importante AccesoriosPiezas incluidas en el kit vea el diagrama Piezas incluidas en el kitInstalación del kit ver también la lista de piezas Reparaciones Piezas de repuestoModelo No. de serie Fecha Remarques Notas Husqvarna South Carolina 542 20 11
Top Page Image Contents