Husqvarna RG 2112 With Machine Cold and Setting Level, Hour Operation Check List, Service Daily

Page 23

PRE-OPERATION CHECKLIST

Before leaving our factory, every machine is thoroughly tested. Follow our instructions strictly and your machine will give you long service in normal operating conditions.

Before starting the machine, make sure that you read this entire Operations Manual and are familiar with the operation of the machine.

WITH MACHINE COLD AND SETTING LEVEL:

Gasoline Models: Check engine oil. Fill to the full mark on dipstick with 10W30 oil, class MS, SD, SE or better.

Electric Models: Verify that all electrical connections are intact.

1-2 HOUR OPERATION CHECK LIST:

ALWAYS place the machine on a level surface with the engine/motor “OFF”, the ignition switch set in the “OFF” position and disconnected from the power source before performing any maintenance. Let the machine cool down!!

1. Check the engine air cleaner hose clamps. Tighten as required. 2. Tension the drive V-belts. DO NOT over tension!

SCHEDULED MAINTENANCE QUICK REFERENCE

Before performing any maintenance, ALWAYS place the machine on a level surface with the engine/motor “OFF”, the ignition switch set in the “OFF” position and disconnected from the power source!

SERVICE DAILY:

1. Check engine oil level.

2. Check all guards for damage.

3. Check hoses and clamps for damage or looseness. Tighten or replace as necessary.

4. Check air cleaner. Clean or replace as required. 5. Clean the machine at the end of the day.

SERVICE EVERY 50 HOURS:

1. Replace engine oil and oil filter. 2. Clean engine air fins.

3. Check V-belt tension. DO NOT over tension! 4. Clean Engine fuel bowl.

23

Image 23

Contents Operator’s manual Page Page Table DES Matières Instructions PáginaPage Page Proposition 65 de Californie Avertissement California Prop 65 WarningAdvertencia Prop 65 de California Advertencia Sobre EL PolvoPage Figures / Figures / Figuras Figures / Figures / Figuras Figures / Figures / Figuras Figures / Figures / Figuras Parts Identification Identification des pièces Identificación de las piezas Do not USE the Tool DOs and DO NOTsDOs and DO NOTs Options Feature ModelLength cm Description Dimensions NoteMaterial Tool Application GuideAttachment Hour Operation Check List With Machine Cold and Setting LevelService Daily Service Every 50 HoursAll Models FeaturesAssembly Check Before OperatingExtension Cord Size Minimum Electric Motor Plugs & ConnectorsGasoline Model Tool InstallationRear Axle Positions See FIG Tool Height for Axle Positions See FIGTungsten Carbide Blocks See FIG Grinding Stones See FIGDiamond Segment Blocks FIG Multi-Segmented Diamond Disks Q See & FIG Wire Brushes See FIGTool Holding Pad HH Installation Operating InstructionsStopping the Unit Gasoline Models Maintenance Incidents During OperationStopping the Unit Electric Models Start / Stop of Gasoline Models & FIGLubrication Points Engine Oil Change ProcedureWhen Required Belt TensionImportant Advise AccessoriesInstallation of Kit Also See Parts List Items included in kit See DiagramModel Serial No Date RepairsSpare Parts Remarques Notas Mises EN Garde Mises EN Garde Caractéristiques Modèle Remarques Article Longueur po DescriptionApplication Matériau Montage Guide d’application d’outilOutil Entretiens Toutes LES 50 Heures Entretiens QuotidiensTous les modèles CaractéristiquesAssemblage Vérifier avant utilisationDu sélecteur de tension Tableau Fiches et connecteurs de moteurs électriquesRelever la protection avant a Desserrer les trois Installation d’outilModèles à essence TableauDisques scarificateurs , FIG Blocs diamant segmentés FIGBloc au carbure de tungstène voir la FIG Disque diamant à segments multiples Q voir , FIG Installation du patin porte-outil HHUtilisation Brosses métalliques voir la FIGArrêt DE LA Machine modèles à essence Problèmes en cours d’utilisationArrêt DE LA Machine modèles électriques Démarrage et arrêt des modèles à essenceVidange d’huile EntretienPoints de lubrification Contenance en huile moteur Honda GXV340Articles compris dans le kit AccessoiresInstallation du kit voir également la liste des pièces Conseils importantsModèle No. de série Date d’achat 11. Réparations12. Pièces détachées Remarques Notas Advertencias Advertencias Opciones ModeloNotas Longitud cm DescripciónFijación a la Material Guía de aplicación de la herramientaServicio Cada 50 Horas Servicio DiarioTodos los modelos CaracterísticasMontaje Revisión antes de manejarTamaño DEL Cordón DE Extensión mínimo TablaTabla Altura mínima de la herramienta Instalación de la herramientaModelo de gasolina Posiciones del eje trasero ver FIGBloques de carburo de tungsteno ver FIG Piedras de pulido ver FIGBloques de segmentos a diamantados FIG Instalación del portaherramienta HH Ver , , , , FIG Muelas escarificadoras , FIGCepillos de alambre FIG Discos diamantados de segmentos múltiples , FIGParo DE LA Máquina modelos de gasolina Instrucciones de operaciónIncidentes durante la operación Paro DE LA Máquina modelos eléctricosProcedimiento para cambiar el aceite del motor MantenimientoPuntos de lubricación Capacidad de aceite del motor Honda GXV340Accesorios Consejo importanteInstalación del kit ver también la lista de piezas Piezas incluidas en el kit vea el diagramaPiezas incluidas en el kit Modelo No. de serie Fecha ReparacionesPiezas de repuesto Remarques Notas Husqvarna South Carolina 542 20 11