DeWalt DS100, DS200 instruction manual System Settings, Clearing a Fault, To Clear a Tamper Fault

2.The fault code will be displayed. Use the up and down arrows to scroll through the faults. Resolve the issue with the action listed in Description of Fault Codes chart and the Fault screen will disappear. To remove a tamper fault, select CLEAR.

IMPORTANT: See the Description of Fault Codes for more details regarding a fault and resolution actions. All faults, except a tamper, will automatically be cleared when the issue has been resolved. An event will be recorded in the event log indicating the date and time that the event occurred and was resolved.

NOTE: A tamper fault will not be automatically cleared. After the device has been inspected, checked for damage, and the cover closed, the fault will need to be cleared. See Clearing a Fault. This process was designed to create awareness of the tamper with the master user and require verification that the problem has been resolved.

CLEARING A FAULT

To clear any fault other than a tamper fault, correct the condition at the sensor. For example: replace the battery, relocate to an area with a better signal, etc.

To Clear a Tamper Fault:

IMPORTANT: Before clearing a tamper fault, be sure that the issue has been resolved. Only the master user can clear tamper faults.

1.When the Fault Code screen is displayed; select CLEAR.

2.Use the keypad to enter the master code.

3.Select OK.

DESCRIPTION OF FAULT CODES

NOTE: See the Troubleshooting Guide for more detailed information.

DESCRIPTION OF FAULT CODES

Fault Code	Fault Display	Description	Action
Power	Primary Power	No power to	Check power supply
	Lost Base	Base Unit
DevPower	Primary Power Lost	No battery power	Change battery, reset
	Device #	in device
BaseLowBatt	Base	Base Unit	Plug in power supply
	Low Battery	battery low	to recharge battery
DevLowBatt	Low Battery	Device battery	Change battery, reset
	Device #	low
WeakSig	Weak Signal	Transmission signal	Check for interference;
	Device #	from device is weak	move device
Unsecured	Unsecured	Device has	Check for intrusion;
	Device #	been tripped	re-secure device
NoCheckIn	No Check In	Device check-in	Check for interference;
	Device #	messages have not	move device
		been received

DESCRIPTION OF FAULT CODES cont.

Fault Code	Fault Display	Description	Action
Tamper	Tamper	Device has been	Close device or
		opened or damaged	replace if damaged
BaseBadBatt	Bad Battery	Base Unit battery has	Needs to be repaired
	Base	dropped below the	at DEWALT authorized
		voltage limit	service center
CellRadio	Cell Radio	Cellular radio	Move Base Unit to
	Fault	signal is lost	a location where
		or scrambled	CELL light is solid;
			call Customer Service
			if problem persists
Receiver	Receiver Fault	2-way transmission	Call customer service
	Device #	of device is lost	to test system for issues
NetControl	Base Network	Base RF processor	Internal check; will clear
	Control	communications	itself; call Customer Service
			if problem persists

NOTE: The battery will take up to 24 hours to charge completely. To avoid draining the battery, do not use an outlet that is controlled by a wall switch. The battery is designed to be a back-up source of power for up to 8 hours. If the monitoring service has been activated, the Base Unit will send a low battery message to the monitoring servce approximately 1 hour before the battery is drained. If power is not restored within that remaining hour, the Base Unit will disarm and shut down.

IMPORTANT: After power has been restored, the Base Unit will not be armed.

FEATURES & OPTIONS

System Settings

The systems settings menu allows for changes in user codes, wireless devices, automatic arming, delays and account information.

•	Wireless Device Maintenance	•	Clear Settings
•	Change Master Code	•	Auto Arm ON/OFF
•	User Code Maintenance	•	Auto Arm Time Set
•	Set Console Devices	•	Review Account
•	Set Delay/Instant	•	Choose Language

WIRELESS DEVICE MAINTENANCE

After the initial setup, a device such as a sensor or Key Chain Remote can be added, edited or removed.

•Adding or Replacing a Device

•Editing a Device

•Removing a Device

1.Start at the main screen.

2.Select MENU or press MAIN MENU on the keypad.

3.Using the keypad, enter the master code.

Features & Options

10