DeWalt DS200, DS100 instruction manual Auto ARM ON/OFF, Auto ARM Time SET, Review Account

Page 22

English

7.The system will request one final check before clearing the settings. All registered sen- sors, sirens, Key Chain Remotes, and users will be deleted from the system. To sim- ply change sensor descriptions, user names or user codes use the System Settings menu instead. To confirm a clearing of the settings, select YES.

See Programming for Initial Setup for instructions on adding sensors and users. Be sure to contact the monitoring service to notify them of the changes.

AUTO ARM ON/OFF

The system can be set to arm at a particular time each day. This feature can be useful to ensure the system can be properly armed if arming cannot be initiated by the master user or other users of the system.

CAUTION: LOUD NOISE. Enabling the auto arm feature will cause a brief, loud noise while arming that may startle any persons near the Base Unit.

1.Start at the main screen.

2.Select MENU or press MAIN MENU on the keypad.

3.Using the keypad, enter the master code.

4.Use the up and down arrows to scroll through the menu until the System Settings screen is displayed. Select OK.

5.Use the up and down arrows to scroll through the menu until the Auto Arm ON/OFF screen is displayed. Select OK.

6.When the Autoarm OFF screen appears, select CHANGE. The CHANGE button toggles between off and on.

7.When the automatic arming is enabled, the Autoarm ON screen will appear. Select EXIT.

IMPORTANT: If a user disarms the system after the auto arm time and still requires protection, the user will need to re-arm the system using the Key Chain Remote or key- pad. The following day, the auto arm will continue to auto arm at the pre-set time.

AUTO ARM TIME SET

The system can be set to arm at a particular time each day. To set or change the time of automatic arming, follow these steps.

1.Start at the main screen.

2.Select MENU or press MAIN MENU on the keypad.

3.Using the keypad, enter the master code.

4.Use the up and down arrows to scroll through the menu until the System Settings screen is displayed. Select OK.

5.Use the up and down arrows to scroll through the menu until the Set Auto Arm Time screen is displayed. To set the time, select OK.

6.Using the numbers on the keypad, choose the time the system is to be automatically armed, changing hours first and then minutes. The character that is being changed will be underlined. To move back a character, use the down arrow. To move forward a char- acter, use the up arrow. Select SET.

7.Choose AM or PM. Use the up and down arrows to toggle between AM and PM. Select SET.

REVIEW ACCOUNT

The user is able to view the account information directly from the Base Unit. This includes contact numbers, the account number, and the mobile identification number.

•Customer Service Information

•Account Number

•MIN – Mobile Identification Number

1.Start at the main screen.

2.Select MENU or press MAIN MENU on the keypad.

3.Using the keypad, enter the master code.

4.Use the up and down arrows to scroll through the menu until the System Settings screen is displayed. Select OK.

15

Page 21 Page 23
Image 22
Page 21 Page 23
Contents Dewalt Page DS100 DS200Table of Contents EnglishImportant Notices General Safety RulesLimitations of System Federal Communications Commission FCC Part Statement Federal Communications Commission FCC Part 68 StatementDS100 Base Unit Industry CanadaDS200 KEY Chain Remote Unique Features DS100 Jobsite Security Portable Alarm System Base UnitPrevention of False Alarms AccessoriesDuring an Alarm Connecting the Equipment Step ONE Choosing a Language Programming for Initial SetupTelephone Connection Step TWO SET Time and DateStep Four Assign Devices To Access the Reset Button on the KEY Chain RemoteIf Master Codes Do Not Match List of Devices CodePAD ALPHA/NUMERIC Chart KEY# of presses Step Five Test RangeUsing the Keypad Step Seven Monitoring ServiceDelays Arming the SystemUsing the KEY Chain Remote Arming AutomaticallyHOW to View Faults FaultsEntry Delays Disarming the SystemTo Clear a Tamper Fault System SettingsClearing a Fault Description of Fault CodesTo Add a Device To Edit a DeviceTo Remove a Device User Code MaintenanceChange Master Code To Remove a User To Add a UserTo Edit a User SET Console DevicesSET DELAY/INSTANT Clear SettingsAuto ARM Time SET Auto ARM ON/OFFReview Account To View the Mobile Identification Number MIN Customer Service information To View Account NumberSet Date/Time Choose LanguageReview Event Log TestConsole Devices To verify, follow these stepsPhone Line StrobeMotion Detector Wireless DevicesExternal Sirens If You Lose Your Master Code Battery MaintenanceBase Unit Battery Turn System OffContact Full One Year Warranty Patent NotificationCoverage Map Cell Phone Text Message Codes Alarm CodesDefault E-mail Meaning Action RequiredDescription of Event Codes Event Code Description ActionTroubleshooting Guide Problem SolutionGlossary of Terms PIRFrançais Table des matières Consignes importantes Règles de sécurité GénéralitésCalibre AWG Limites du système NormesAvertissement Télécommande PORTE-CLÉS DS200Industrie Canada Base DS100Caractéristiques uniques Accessoires Prévention des fausses alertesPendant une alerte Connexion de l’équipementÉtape UN Choix DE LA Langue Programmation de la configuration initialeConnexion téléphonique Étape Deux Réglage DE L’HEURE ET DE LA DateÉtape Quatre Assignation DES Dispositifs Étape Trois Configuration DU Code MaîtreSi les codes maître ne cadrent pas Appuyer Diagramme ALPHA/NUMÉRIQUE ClavierListe des dispositifs Code Étape Cinq Test DE PortéeArmement du système Étape Sept Service DE SurveillanceÉtape SIX Addition D’UTILISATEURS Délais Utilisation DE LA Télécommande PORTE-CLÉSUtilisation DU Clavier Désarmement du système Configuration DES DélaisArmement Automatique Effacer UNE Erreur ErreursComment Afficher LES Erreurs Pour éliminer une erreur due à une altérationDescription DES Codes Derreurs Options du systèmeDescription DES Codes D’ERREURS Entretien DES Dispositifs Sans FilsPour modifier un dispositif Pour supprimer un dispositifMise À Jour DU Code Utilisateur Changer LE Code MaîtrePour ajouter un utilisateur Pour modifier un utilisateur Configuration DES Dispositifs DE ConsolePour supprimer un utilisateur Option DÉLAI/INSTANT Configuration DE L’ARMEMENT AutomatiqueRéinitialisation DES Options Mise À L’HEURE DE L’ARMEMENT Automatique Revue DU ComptePour afficher le numéro d’identification mobile NIM Réglage heure/datePour afficher le numéro de compte Choisir LE LangageDescription DES Évènements Revue du rapport dactivitésSituation DU Rapport D’ACTIVITÉS Exécution D’UN TestDispositifs DE Console Pour le vérifier, suivre les étapes ci-aprèsLigne Téléphonique StroboscopeDétecteur de mouvements SirèneDispositifs Sans FIL Arrêt du système En cas de perte du code maîtreEntretien des piles Contact Garantie complète dun an Déclaration de brevetCarte de la zone de couverture cellulaire analogique AppendiceCodes DES Voyants DEL Continu Clignotant Éteint MauvPileBseCodes DES Messages Textuels DU Telephone Cellulaire Diagramme ALPHA/NUMÉRIQUEAppuyer Description DES Codes Dévènement Code dévènement Description ActionRadio Cell NON Validé Problème Solution Guide de dépannageGlossaire Español Índice Notificaciones importantes Instrucciones de seguridad generalRestricciones del sistema Notificaciones Reglamentarias Unidad Base DS100 Ministerio de Industria de Canadá Industry CanadaAdvertencias Control Remoto DE Llavero DS200Características exclusivas Prevención de falsas alarmas AccesoriosQue hacer durante una alarma Primer Paso Elección DEL Idioma Programación de la configuración inicialConexión telefónica Segundo Paso Programación DE Hora Y FechaSi los códigos maestros no corresponden Tercer Paso Fijación DEL Código MaestroCuarto Paso Asignación DE LOS Dispositivos # de veces presionado Lista de dispositivos CódigoCuadro Alfanumérico Quinto Paso Prueba DE AlcanceSexto Paso Agregar Usuarios Séptimo Paso Monitoreo DEL ServicioUSO DEL Teclado Armado del sistemaRetrasos USO DEL Control Remoto DE LlaveroArmado Automático Desarmado del sistemaRetrasos DE Entrada Cómo Despejar UNA Falla FallasCómo VER Fallas Para despejar una falla por alteraciónPara agregar un dispositivo Configuraciones del sistemaMantenimiento DE Dispositivos Inalámbricos Código de falla Falla en pantalla Descripción AcciónPara editar un dispositivo Para borrar un dispositivoMantenimiento DE LOS Códigos DE Usuario Cómo Cambiar EL Código MaestroPara agregar un usuario Para borrar un usuario Para editar un usuarioCómo Fijar LOS Dispositivos EN LA Consola Cómo Despejar LAS Configuraciones Cómo Fijar LA Modalidad DE Activación RETRASADA/INSTANTÁNEAFijación DE LA Hora DE Armado Automático Encendido Y Apagado DEL Armado AutomáticoRevisión DE LA Cuenta Para ver el Número de Identificación Móvil MIN Programación de fecha/horaElección DEL Idioma Ubicación DEL Registro DE Eventos Revisión del registro de eventosPrueba Descripción DE EventosLínea Telefónica Radio CelularPara verificar, siga estos pasos Dispositivos DE LA ConsolaDetector de movimiento SirenaDispositivos Inalámbricos Mantenimiento de pilas Si pierde su código maestroApagado del sistema Sirenas ExterioresPila DE LA Unidad Base Contacto Garantía completa por un añoNotificación de la patente Pilas DE DispositivosApéndice Códigos DE Luces LED LUZ LED Sólida Destellante Apagada Notificación por Códigos DE Mensajes DE Texto DEL Teléfono CelularSignificado Acción Descripción DE Códigos DE Eventos Código de evento Descripción AcciónBorrado Problema Solución Guía de resolución de problmasGlosario Page

DS100, DS200 specifications

DeWalt has long been recognized as a leader in the power tool industry, and its DS200 and DS100 models continue this tradition by offering innovative features and reliable performance. Both models are designed with contractors and DIY enthusiasts in mind, providing durability and efficiency in various applications.

The DeWalt DS200 is a dual-speed, heavy-duty job site radio designed to withstand the rigors of construction environments. It boasts an impressive 20V MAX lithium-ion battery compatibility, allowing for extended battery life and convenience on the job site. One of the main features of the DS200 is its Bluetooth connectivity, enabling users to stream music directly from their smartphones or tablets. This added functionality allows for a more enjoyable work environment, fostering motivation and focus.

The sound quality of the DS200 is exceptional, featuring high-performance speakers and a digital sound processing system. Its rugged exterior is designed to protect it against dust and moisture, making it highly suitable for outdoor use. The DS200 also features a built-in USB port, allowing users to charge their devices while on the go. Additionally, its integrated hooks and available carrying handle offer enhanced portability, enabling easy transportation from one job site to another.

On the other hand, the DeWalt DS100 is a more compact and lightweight option, perfect for those seeking a portable audio solution without compromising on sound quality. The DS100 also supports 20V MAX lithium-ion batteries, ensuring compatibility and extending battery runtime. With its integrated Bluetooth technology, users can easily connect their devices and enjoy crisp audio performance.

The DS100's design prioritizes convenience, featuring a durable carry strap and a compact size that allows it to fit comfortably in small spaces. Despite its smaller stature, the DS100 does not sacrifice sound quality, providing rich audio capable of filling a room.

Both models exemplify DeWalt's commitment to quality and innovation. With their robust designs and advanced technologies, the DS200 and DS100 cater to the needs of modern users, making them essential tools for both professional contractors and home improvement enthusiasts. Whether in the workshop or on the job site, these audio solutions enhance productivity and elevate the working experience.
Top Page Image Contents