•Signals sent by wireless devices may be blocked or reflected by metal before they reach the receiver. Even if the signal path has been recently checked during a routine test, blockage can occur if a metal object is moved into the path.
•A telephone line, either cellular or landline, is needed to transmit alarm signals to the monitoring system. If reception is not available, telephone lines are out of service, or the telephone company makes changes to its facilities, the outgoing call cannot be placed.
•This equipment uses an RJ-11 jack to connect to the telephone network. If another device, such as a telephone, fax or modem, is utilizing the connected phone line, this equipment will not interrupt the device currently in use.
•If utilizing a landline, high-speed data formats such as DSL could affect the ability to reach the monitoring system. You may need to install a filter provided by your DSL company. Even with a filter, there is still a possibility the equipment will not be able to communicate with the monitoring system.
•Wireless devices have a limited range. If they are placed out-of-range, they will not be able to send or receive signals with the Base Unit.
•Passive Infrared Motion Detectors can only detect intrusion within the designated ranges as diagrammed in their instruction manual. Passive Infrared Motion Detectors do not provide volumetric area protection. They do create multiple beams of protection and intrusion can only be detected in unobstructed areas covered by those beams. They cannot detect motion or intrusion that takes place behind walls, ceilings, floors, closed doors, glass partitions, glass doors or windows. Mechanical tampering, masking, painting or spraying of any material on the mirrors, windows or any part of the optical system can reduce their detection ability. Passive Infrared Motion Detectors sense changes in temperature; thus, as the ambient temperature of protected area approaches the temperature range of 90º to 105ºF (32º to 40ºC), the detection performance can decrease.
•This system is a self-installed security system. Carefully follow all instructions. Improper installation may compromise the operation of this equipment.
•This alarm system should be tested regularly to make sure all sensors and transmit- ters are working properly.
•Even if the system responds to an intrusion as intended, the users may have insufficient time to protect their assets and property. To provide the best support, customer service must be notified of any change of site and device additions or deletions. Even with mon- itoring, the authorities may not respond appropriately.
•Warning devices, such as sirens and strobe lights, may not alert people if no one is in range or not on the premises. Persons may not hear the warning if the alarm is muffled from a radio, operating equipment, appliances or by passing traffic. Alarm warning devices, however loud, may not warn hearing-impaired people. Similarly, the strobe light may not be seen by vision-impaired people.
•In the event of an intrusion, the system is designed to contact the monitoring system. Even if a call is placed, the user may not be able to respond quickly enough.
•Despite advanced design and regular testing, this equipment, like other electrical devices, is subject to component failure.
•Installing this system with a monitoring service may make one eligible for lower insurance rates, but a security system is not a substitute for insurance.
REGULATORY NOTICES
Federal Communications Commission (FCC) Part 15
Statement
•This equipment (Base Unit and Key Chain Remote) has been tested and complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and (2) the device must accept any interference received, including interference that may cause undesired operation.
•If this equipment does cause harmful interference to radio or television reception, which can be determined by placing the equipment in standby mode, try to correct the interference by one or more of the following measures:
1.Reorient the antenna of the radio/TV experiencing the interference.
2.Relocate the Base Unit with respect to the radio/TV.
3.Move the antenna leads away from any wire that runs to the Base Unit.
4.Plug the Base Unit into an outlet on a different electrical circuit from the radio/TV experiencing the interference.
5.If necessary, consult DEWALT or an experienced radio/TV technician for help.
6.Additional suggestions can be found in the following booklet prepared by the Federal Communications Commission “Interference Handbook” This book is available from the U.S. Government Printing Office, Washington, DC 20402.
•Any changes or modifications to the equipment, not specifically approved by DEWALT, can void the user’s authority to operate the equipment.
FCC ID: HCQ3B6ECNCA (Base Unit) and
FCC ID: HCQ3B6ETRT2M (Key Chain Remote)
Federal Communications Commission (FCC) Part 68 Statement
•This equipment (DS100) complies with Part 68 of the FCC Rules and the requirements adopted by the ACTA. Located on the equipment (DS100) is a label that contains, among other information, a product identifier that has the format US: AAAEQ##TXXXX. If requested, this information must be provided to the telephone company.
•The REN is used to determine the number of devices which may be connected to a telephone line. Excessive RENs on a telephone line may result in devices not ringing in response to a call. In most, but not all areas, the sum of all REN devices should not exceed an REN of five (5.0). To determine the REN for your calling area, contact the telephone company. The REN is part of the product identifier that has the format US: AAAEQ##TXXXX. The digits represented by ## are the REN without a decimal point (e.g., 03 is a REN of 0.3).
•This equipment (DS100) uses an RJ-11 jack to connect to the telephone network. If another device, such as a telephone, fax or modem, is utilizing the connected phone line, this equipment will not interrupt the device previously in use.
•If this equipment (DS100) causes harm to the telephone network, the telephone com- pany will notify you in advance that temporary discontinuance of service may be required. If advance notice is not practical, they will notify you as soon as possible. You will be advised of your right to file a complaint with the FCC if you deem necessary.
•The telephone company may make changes in its facilities, equipment, operations or procedures that could affect the operation of the equipment (DS100). You will be given advance notice in order to maintain uninterrupted service.
•If trouble is experienced with this equipment (DS100), please call 1-800-4-DEWALT (1-800-433-9258) for repair and warranty information. If the trouble is causing harm to the telephone network, the telephone company may request you remove the equip- ment from the network until the problem is resolved.
•There are no user serviceable components in this equipment (DS100). All necessary repairs must be made by a DEWALT authorized service center.
•This equipment (DS100) may not be used on coin service provided by the telephone company.
•Connection to party lines is subject to state tariffs. Contact the state public utility com- mission, public service commission, or corporation commission for information.
US: HCQAL00B6263-BDK
