ENGLISH
USER MANUAL
BATTERY FLUID LEVEL CHECK
WARNING!
Protect body parts (eyes, hair, hands, etc.) properly, when performing battery check and cleaning procedures.
1.Engage the parking brake (21, Fig.
2.Turn off the engine, by turning the ignition key (17, Fig.
3.Open the driver's seat hood (8, Fig. F).
4.Check the electrolyte level in the battery (43, Fig. E) and, if necessary, top up with distilled water.
5.If necessary, clean the battery.
6.Check the battery terminal connections for oxidation.
7.Close the driver's seat hood (8, Fig. F).
BRAKE FLUID LEVEL CHECK
1.Engage the parking brake (21, Fig.
2.Turn off the engine, by turning the ignition key (17, Fig.
3.Lift the hopper completely according to the procedure shown in the relevant paragraph.
4.Install the support rods (4, Fig. F).
5.Check that the fuel level in the tank (12, Fig. F) is between the minimum and maximum marks. If necessary, top up using the same type of fl uid that is in the line.
6.Type of fl uid used: DOT4.
7.Remove the support rods (4, Fig. F) and lower the hopper.
REVERSE GEAR BUZZER OPERATION CHECK (OPTIONAL)
1.Check that, when the machine moves in reverse, the relevant buzzer sounds.
2.If necessary, adjust the relevant sensor according to the instructions in the Service Manual.
TYRE PRESSURE CHECK
1.Engage the parking brake (21, Fig.
2.Turn off the engine, by turning the ignition key (17, Fig.
3.The tyre pressure should be as follows:
• | Front tyres: | 7.0 Bar |
• | Rear tyres: | 7.0 Bar |
WARNING!
Please respect the recommended tyre pressure as stated in the relevant decals.
The manufacturer rating is based on standard drive speed and standard load rating, different from the actual machine application.
SIDE BROOM HEIGHT CHECK AND
ADJUSTMENT
1.Check the side broom print according to the following procedure:
2.Drive the machine on a level ground.
3.While keeping the machine stationary, lower the side brooms and allow them to turn for a few seconds.
4.Stop and lift the side broom, then move the machine.
5.Check that the side broom print is as shown in the fi gure (Fig. M) according to the machine direction (3, Fig. M).
•The right side broom must touch the ground along a circle arc ranging from "9 o'clock" position to "4 o'clock" position (1, Fig. M).
•The left side broom must touch the ground along a circle arc ranging from "8 o'clock" position to "3 o'clock" position (2, Fig. M).
6.If the print is not within specifi cations, adjust the side broom height by using the screw (1, Fig. N).
NOTE
When the side brooms are too worn out, the adjustment is not possible; replace the brooms according to the instructions in the relevant paragraph.
SIDE BROOM REPLACEMENT
NOTE
Brooms of various hardness are available. This procedure is applicable to all types of brooms.
CAUTION!
It is advisable to wear protective gloves when replacing the side brooms because there can be sharp debris between the bristles.
1.Prepare the machine as shown in After Using the Machine paragraph.
2.Start the engine as shown in the relevant paragraph.
3.Turn the engine throttle lever (19, Fig. B - 29, Fig. C) to “MAX”.
4.Push and hold the right distributor lever (12, Fig. B - 31, Fig. C) to lift the hopper (2, Fig. F) as necessary in order to reach the area under the side broom.
5.Turn off the engine, by turning the ignition key (17, Fig.
6.Remove the locking screw (1, Fig. P), then remove the side broom and replace it.
7.Fasten the side broom with the screw (1, Fig. P).
8.Lower the hopper (2, Fig. F) by pulling and holding the right distributor lever (12, Fig. B - 31, Fig. C).
20
SR 1800S D 2WD