Wayne-Dalton 3790-Z installation instructions Package Contents

Page 2

Package Contents

NOTE: Depending on the opener model purchased, some accessories listed will not be supplied.

Controls

Opener

Key chain/Visor
Transmitter (2)
per
O	at
o	e
T	D
Press
	o
	o
	Here	r
		r

Disconnect Cable

1 2

3 4

5 6

7 8

9 0

Mounting Bracket

5 Button Wireless

Keyless Entry

Disconnect Handle

“S” Hook

Disconnect

Handle Bracket

Cable Clips (4)

Jumper

(Optional for Safety Sensors)

INSTALLATION INSTRUCTIONS AND OWNER’S MANUAL

for TORQUEMASTER /

TORQUEMASTER PLUS

Models: 3790/3790-Z

Installation Instructions

and Owner’s Manual

CAUTION!!

Only for use without Photo Eyes on Wayne-Dalton 9000 series, 5120 & 5140 doors. All others Must use Photo Eyes.

USE OF THIS MANUAL

WHEN INSTALLING A NEW DOOR WITH AN IDRIVE :

If you just ﬁ nished installing a new garage door along with an idrive opener, then proceed with these instructions beginning with Step 15 on page 21. If you were referred to these instructions as part of a new door installation, then proceed with these instructions beginning with Step 1 on page 7.

IMPORTANT NOTICE!
To avoid possible injury, read the enclosed instructions carefully
before installing/operating this garage door opener. Pay close
attention to all warnings and notes. This manual MUST be attached
to the wall in close proximity to the garage door opener.	GARAGE DOORS & OPENERS

Deluxe Multi-function

Wireless Wall Station

Emergency

Disconnect Label

Security Light with Diffuser

(Not available with model #3790-Z)

1/4” x 2" Hex Head Lag

Screws (2)

1/4” x 1-1/2" Hex Head

Lag Screws (4)

Entrapment Label

Lock Arm Assembly

#6 x 7/8" Phillips Pan

Head Screws (4)

#6-20 x 1/2" Phillips Pan Head Screw (1)

Copyright 2007 Wayne-Dalton Corp. Part No. 334101 Rev 1 1/15/2008

	Owner’s Manual	Installation DVD	#6-32 x 3/4" Phillips Pan Head	5mm x .8mm x 12mm
		Installation DVD	Screw (1)	Phillips Pan Head Screw (1)
			Screw (1)	Phillips Pan Head Screw (1)
			(For Light Fixture)	(For Lock Arm)

IPlease Do Not Return This Product To The Store. Call Us Directly! Our Trained Technicians Will Answer Your Questions and/or Ship Any Parts You May Need.

You can reach us Toll Free at 1-888-827-3667 for Consumer Assistance or online at www.wayne-dalton.com

Image 2

Contents Network Copyright 2008 Wayne-Dalton Corp. Part No Rev 2 7/16/2008Your ForPackage Contents When Installing a NEW Door with AN Idrive Look for this symbolEyes to Prevent Possible Severe or Fatal Injury Pre-InstallationInspection WAYNE-DALTON Track Radius Photoelectric LOW Head System RequirementsTools Needed Door Models below require the use of photo eyesTable of Contents Deﬁnition of key words used in this manualRemoval Retro-Fit InstallationDrum Wrap & End Bracket Spring Tension RemovalBracket and Gear End Bracket RemovalCenter Bracket & Cable Drum Even Fatal Injury Retro-Fit InstallationPowerful Spring Releasing ITS IMPORTANT! Right and Left Hand isEnd Bracket Removal RemovalTop Bracket Re-Install If NecessaryVertical Track Height Adjustment 8000/8100/8200 TrackTracks to the Support Before Opening Door can Cause Door Top Roller AdjustmentFailure to RE-ATTACH Horizontal Installation Assembling OpenerCable Drums End Brackets Tools Needed Power Drill Socket Driver Wrench Step LadderSecure end bracket to the flag angle using Repeat for other end bracketInstallation Cable Drum/ Drive GearCounterbalance Springs End Bracket InstallationBrackets Support Bracket Positioning Support BracketAttaching Opener To Bracket Attaching Disconnect CablePliers Slack between opener and right endHandle Bracket Pilot drill lag screw location using 1/8 drill bitMounting Disconnect 6ftAttaching Disconnect Handle Disconnect Handle UsageCable Adjustments SpringsTools Needed Vice Clamps Securing DoorFor Spring Winding Winding Springs HandsTools Needed Drum Wrap InstallationRecommended Spring Turns IMPORTANT! do not Overwind SpringsIMPORTANT! do not Overwind Setting Spring TensionProblems SCREWS. for Detailed Information onDrum Wrap Installation Mounting Wall StationInstalling Battery Install hole plug into the screw hole in the light fixture Installing the Light FixtureDisconnect Power to If IncludedAttaching Diffuser Connecting OpenerPower Cord If IncludedFor Proper Alignment Sensor UnitSensor Wire Installation View of the Opener from the FrontSafety Sensor Alignment Checking for ObstructionsProfile Routine Standard Upper Limit On when program button is pushedProgramming Light Fixture On and remain on for 30 secondsWork Properly Adjusting DetentProfile Routine Custom Upper Limit Turn increments Lock Arm InstallationConfirm adjustment Tools Needed Tape Measure Step LadderLock Arm Installation Contact Obstruction TestTesting the Safety Sensors Fatal Injury MAY ResultEmergency Disconnect Read and Follow ALL InstructionsDoor activation Never GO Under a STOPPED, Partially Open DoorOperating the Wireless Wall Station Programming/Training HomeLink Unit Teaching HomeLink to the idrive openerProgramming/Training HomeLink Unit Multi-Door Programming Customizing the SettingsCustom pet position For more profile options go to page 28Maintenance Confirm pot nut position* shown below Power Connection Permanent Wiring OptionReconnect Power Potentiometer GearRed Program Button Stations or Transmitters to OpenerProgramming Wireless WallHandle In Manual Door Operated Position Motor Up Position Light Button Large ButtonTroubleshooting Symptom Probable Cause Corrective ActionLock Arm Troubleshooting Dalton dealer or distributor Pre-drill 5/64 pilot hole Cut-Out Template to Aid InstallationPre-drill 3/32 pilot hole Thank you for your purchasePatent Information Models 3790/3790-Z