Wayne-Dalton 3790-Z installation instructions Safety Sensor Alignment, Checking for Obstructions

Page 33

21

Top View

Safety Sensor Alignment

Tools Needed:

Align the safety sensors by moving the

In

In

Pliers

sending and receiving units in or out until

the alignment light on the receiving unit

comes on. The 1/4”-20 carriage bolt can be

loosened to move the safety sensor in or

out, as required. If you have difficulty

aligning the beams, check that both

Out

Out

mounting brackets are mounted at the

same height and remount if necessary.

Additional minor adjustments can be made

1/4”-20 Carriage

by slightly bending the mounting brackets.

Bolts

Once the alignment light comes on, tighten

all bolts and mounting screws. Finish

securing all wires making sure not to break

or open any of the conductors. Loop and

secure any excess wire.

For this adjustment, bend

Bracket at wall mount

Top View

22

Securing the Opener

and Checking for Obstructions

Tools Needed:

With the emergency disconnect still in the

7/16” Wrench

manual door operated position, manually

raise the door to the fully open position.

Step Ladder

Then, manually lower the door to the fully

Z-Wave®enabled

Controls

closed position verifying freedom of

what’s

Learn

S1

S2

OPENING

S3

S4

Delete

movement and good door balance.

®

your world?

With Z-Wave

technology you can

Tighten both 1/4”-20 flange nuts, securing

control your lights,

your

t

hermostat andstart

morning coffee,

the opener to the support bracket.

allwiththe single

touch of a

button.

www

Find out more:

.Wayne-Dalton.com/access

NOTE: Good door balance and freedom of

P/N 335982

movement are essential for proper opener

performance. If door is heavy to lift, hard to

close or if door sticks or binds in

the track, make proper adjustments now.

Support	1/4” - 20
Bracket	Flange Nuts

PRE-OPERATION

Please Do Not Return This Product To The Store. Call Us Directly! Our Trained Technicians Will Answer Your Questions and/or Ship Any Parts You May Need. 27 You can reach us Toll Free at 1-888-827-3667 for Consumer Assistance or online at www.wayne-dalton.com

Image 33

Contents Your Copyright 2008 Wayne-Dalton Corp. Part No Rev 2 7/16/2008Network ForPackage Contents Look for this symbol When Installing a NEW Door with AN IdrivePre-Installation InspectionEyes to Prevent Possible Severe or Fatal Injury Tools Needed System RequirementsWAYNE-DALTON Track Radius Photoelectric LOW Head Door Models below require the use of photo eyesDeﬁnition of key words used in this manual Table of ContentsDrum Wrap & End Bracket Retro-Fit InstallationRemoval Spring Tension RemovalEnd Bracket Removal Center Bracket & Cable DrumBracket and Gear Powerful Spring Releasing ITS Retro-Fit InstallationEven Fatal Injury IMPORTANT! Right and Left Hand isRemoval End Bracket RemovalVertical Track Height Adjustment Re-Install If NecessaryTop Bracket 8000/8100/8200 TrackTop Roller Adjustment Failure to RE-ATTACH HorizontalTracks to the Support Before Opening Door can Cause Door Assembling Opener InstallationCable Drums Secure end bracket to the flag angle using Tools Needed Power Drill Socket Driver Wrench Step LadderEnd Brackets Repeat for other end bracketCable Drum/ Drive Gear InstallationEnd Bracket Installation BracketsCounterbalance Springs Positioning Support Bracket Attaching Opener ToSupport Bracket Pliers Attaching Disconnect CableBracket Slack between opener and right endMounting Disconnect Pilot drill lag screw location using 1/8 drill bitHandle Bracket 6ftDisconnect Handle Usage Attaching Disconnect HandleSprings Cable AdjustmentsSecuring Door For Spring WindingTools Needed Vice Clamps Hands Winding SpringsRecommended Spring Turns Drum Wrap InstallationTools Needed IMPORTANT! do not Overwind SpringsProblems Setting Spring TensionIMPORTANT! do not Overwind SCREWS. for Detailed Information onMounting Wall Station Drum Wrap InstallationInstalling Battery Disconnect Power to Installing the Light FixtureInstall hole plug into the screw hole in the light fixture If IncludedPower Cord Connecting OpenerAttaching Diffuser If IncludedSensor Unit For Proper AlignmentView of the Opener from the Front Sensor Wire InstallationChecking for Obstructions Safety Sensor AlignmentProgramming Light Fixture On when program button is pushedProfile Routine Standard Upper Limit On and remain on for 30 secondsAdjusting Detent Profile Routine Custom Upper LimitWork Properly Confirm adjustment Lock Arm InstallationTurn increments Tools Needed Tape Measure Step LadderContact Obstruction Test Lock Arm InstallationFatal Injury MAY Result Testing the Safety SensorsDoor activation Read and Follow ALL InstructionsEmergency Disconnect Never GO Under a STOPPED, Partially Open DoorOperating the Wireless Wall Station Teaching HomeLink to the idrive opener Programming/Training HomeLink UnitProgramming/Training HomeLink Unit Custom pet position Customizing the SettingsMulti-Door Programming For more profile options go to page 28Maintenance Reconnect Power Power Connection Permanent Wiring OptionConfirm pot nut position* shown below Potentiometer GearHandle In Manual Door Operated Position Motor Up Position Stations or Transmitters to OpenerProgramming Wireless WallRed Program Button Light Button Large ButtonSymptom Probable Cause Corrective Action TroubleshootingLock Arm Troubleshooting Dalton dealer or distributor Pre-drill 3/32 pilot hole Cut-Out Template to Aid InstallationPre-drill 5/64 pilot hole Thank you for your purchaseModels 3790/3790-Z Patent Information