Wayne-Dalton 3790-Z installation instructions Lock Arm Installation, Contact Obstruction Test

Page 37

Lock Arm Installation

(Continued)

Once track radius has been determined, secure the lock arm to the motor with

(1) 5mm x .8mm phillips pan head screw.

NOTE: If unsure of track radius, begin with lock arm in position 1.

After assembly of the lock arm, manually raise and lower the door and verify that the lock arm does not interfere with the door. If there is interference between the door and the lock arm, see Page 42 for lock arm troubleshooting.

NOTE: Do not operate the door or opener if there is interference between the lock arm and the door.

Reconnect the door to the motor operated position. Activate a motor operated up/down cycle to confirm clearance.

P/N 335982

Lock Arm

Motor

		Z-Wave	enabled
		what’s
		OPENING
	t	your world?
		With Z-Wave
	echnology		®
			you can
	control

	t	your lights,
	hermostat
		andstart
	your mor
		ning coffee,
	allwiththe single
	touch
		of a button.
		Find out more:
	www.Wayne-
		Dalton.com/access

5mm x 8mm

Phillips

Pan Screw

	28	Contact Obstruction Test
		Contact Obstruction Test

	Tools Needed:	After installing the opener, the door must
	2 x 4 Board	reverse when it contacts a 1-1/2” high
	2 x 4 Board	object (or a 2 x 4 board laid flat) on the
		object (or a 2 x 4 board laid flat) on the
		garage floor.
		Using the wall station, activate the door
		to the fully open position.
		Place a 2 x 4 board flat on the garage
		floor, under the door path.
		Activate the door to the closed position
		with the wall station. Upon contacting the
		2 x 4 board, the door should stop, then
		reverse direction within two seconds and
		travel to the full open position.
		If the door does not respond to the
		required tests, repeat profile routine Step
		24 or 25, making sure the door is in the
		fully closed position prior to activation.

Center Of Door

2 x 4 Laid Flat

On Floor

WARNING

IF OPENER DOES NOT RESPOND PROPERLY TO THESE TESTS (STEPS

28 AND 29), DO NOT USE DOOR UNTIL A QUALIFIED SERVICE PERSON HAS MADE NECESSARY ADJUSTMENTS/REPAIRS, OR SEVERE OR FATAL INJURY COULD RESULT FROM OPERATING THE DOOR/OPENER.

PRE-OPERATION

Please Do Not Return This Product To The Store. Call Us Directly! Our Trained Technicians Will Answer Your Questions and/or Ship Any Parts You May Need. 31 You can reach us Toll Free at 1-888-827-3667 for Consumer Assistance or online at www.wayne-dalton.com

Image 37

Contents Your Copyright 2008 Wayne-Dalton Corp. Part No Rev 2 7/16/2008Network ForPackage Contents Look for this symbol When Installing a NEW Door with AN IdriveInspection Pre-InstallationEyes to Prevent Possible Severe or Fatal Injury Tools Needed System RequirementsWAYNE-DALTON Track Radius Photoelectric LOW Head Door Models below require the use of photo eyesDeﬁnition of key words used in this manual Table of ContentsDrum Wrap & End Bracket Retro-Fit InstallationRemoval Spring Tension RemovalCenter Bracket & Cable Drum End Bracket RemovalBracket and Gear Powerful Spring Releasing ITS Retro-Fit InstallationEven Fatal Injury IMPORTANT! Right and Left Hand isRemoval End Bracket RemovalVertical Track Height Adjustment Re-Install If NecessaryTop Bracket 8000/8100/8200 TrackFailure to RE-ATTACH Horizontal Top Roller AdjustmentTracks to the Support Before Opening Door can Cause Door Assembling Opener InstallationCable Drums Secure end bracket to the flag angle using Tools Needed Power Drill Socket Driver Wrench Step LadderEnd Brackets Repeat for other end bracketCable Drum/ Drive Gear InstallationBrackets End Bracket InstallationCounterbalance Springs Attaching Opener To Positioning Support BracketSupport Bracket Pliers Attaching Disconnect CableBracket Slack between opener and right endMounting Disconnect Pilot drill lag screw location using 1/8 drill bitHandle Bracket 6ftDisconnect Handle Usage Attaching Disconnect HandleSprings Cable AdjustmentsFor Spring Winding Securing DoorTools Needed Vice Clamps Hands Winding SpringsRecommended Spring Turns Drum Wrap InstallationTools Needed IMPORTANT! do not Overwind SpringsProblems Setting Spring TensionIMPORTANT! do not Overwind SCREWS. for Detailed Information onMounting Wall Station Drum Wrap InstallationInstalling Battery Disconnect Power to Installing the Light FixtureInstall hole plug into the screw hole in the light fixture If IncludedPower Cord Connecting OpenerAttaching Diffuser If IncludedSensor Unit For Proper AlignmentView of the Opener from the Front Sensor Wire InstallationChecking for Obstructions Safety Sensor AlignmentProgramming Light Fixture On when program button is pushedProfile Routine Standard Upper Limit On and remain on for 30 secondsProfile Routine Custom Upper Limit Adjusting DetentWork Properly Confirm adjustment Lock Arm InstallationTurn increments Tools Needed Tape Measure Step LadderContact Obstruction Test Lock Arm InstallationFatal Injury MAY Result Testing the Safety SensorsDoor activation Read and Follow ALL InstructionsEmergency Disconnect Never GO Under a STOPPED, Partially Open DoorOperating the Wireless Wall Station Teaching HomeLink to the idrive opener Programming/Training HomeLink UnitProgramming/Training HomeLink Unit Custom pet position Customizing the SettingsMulti-Door Programming For more profile options go to page 28Maintenance Reconnect Power Power Connection Permanent Wiring OptionConfirm pot nut position* shown below Potentiometer GearHandle In Manual Door Operated Position Motor Up Position Stations or Transmitters to OpenerProgramming Wireless WallRed Program Button Light Button Large ButtonSymptom Probable Cause Corrective Action TroubleshootingLock Arm Troubleshooting Dalton dealer or distributor Pre-drill 3/32 pilot hole Cut-Out Template to Aid InstallationPre-drill 5/64 pilot hole Thank you for your purchaseModels 3790/3790-Z Patent Information