Wayne-Dalton 3790-Z Mounting Disconnect, Handle Bracket, 6ft, 4 x 1-1/2 lag screws

Page 20

7	Mounting Disconnect
	Mounting Disconnect
	Handle Bracket

Tools Needed:

Pencil

Tape Measure

Power Drill

1/8" Drill Bit

7/16” Socket

Driver

Mark a location on the right jamb, 6 feet above the floor to mount the disconnect handle bracket.

Pilot drill lag screw location using 1/8" drill bit.

Align top of the bracket with the mark. Fasten bracket to the jamb with

(2) 1/4” x 1-1/2" lag screws.

6ft

1/4” x 1-1/2” Lag Screws

Disconnect

Handle Bracket

14Please Do Not Return This Product To The Store. Call Us Directly! Our Trained Technicians Will Answer Your Questions and/or Ship Any Parts You May Need.

You can reach us Toll Free at 1-888-827-3667 for Consumer Assistance or online at www.wayne-dalton.com

Image 20

Contents Copyright 2008 Wayne-Dalton Corp. Part No Rev 2 7/16/2008 YourNetwork ForPackage Contents When Installing a NEW Door with AN Idrive Look for this symbolEyes to Prevent Possible Severe or Fatal Injury Pre-InstallationInspection System Requirements Tools NeededWAYNE-DALTON Track Radius Photoelectric LOW Head Door Models below require the use of photo eyesTable of Contents Deﬁnition of key words used in this manualRetro-Fit Installation Drum Wrap & End BracketRemoval Spring Tension RemovalBracket and Gear End Bracket RemovalCenter Bracket & Cable Drum Retro-Fit Installation Powerful Spring Releasing ITSEven Fatal Injury IMPORTANT! Right and Left Hand isEnd Bracket Removal RemovalRe-Install If Necessary Vertical Track Height AdjustmentTop Bracket 8000/8100/8200 TrackTracks to the Support Before Opening Door can Cause Door Top Roller AdjustmentFailure to RE-ATTACH Horizontal Installation Assembling OpenerCable Drums Tools Needed Power Drill Socket Driver Wrench Step Ladder Secure end bracket to the flag angle usingEnd Brackets Repeat for other end bracketInstallation Cable Drum/ Drive GearCounterbalance Springs End Bracket InstallationBrackets Support Bracket Positioning Support BracketAttaching Opener To Attaching Disconnect Cable PliersBracket Slack between opener and right endPilot drill lag screw location using 1/8 drill bit Mounting DisconnectHandle Bracket 6ftAttaching Disconnect Handle Disconnect Handle UsageCable Adjustments SpringsTools Needed Vice Clamps Securing DoorFor Spring Winding Winding Springs HandsDrum Wrap Installation Recommended Spring TurnsTools Needed IMPORTANT! do not Overwind SpringsSetting Spring Tension ProblemsIMPORTANT! do not Overwind SCREWS. for Detailed Information onDrum Wrap Installation Mounting Wall StationInstalling Battery Installing the Light Fixture Disconnect Power toInstall hole plug into the screw hole in the light fixture If IncludedConnecting Opener Power CordAttaching Diffuser If IncludedFor Proper Alignment Sensor UnitSensor Wire Installation View of the Opener from the FrontSafety Sensor Alignment Checking for ObstructionsOn when program button is pushed Programming Light FixtureProfile Routine Standard Upper Limit On and remain on for 30 secondsWork Properly Adjusting DetentProfile Routine Custom Upper Limit Lock Arm Installation Confirm adjustmentTurn increments Tools Needed Tape Measure Step LadderLock Arm Installation Contact Obstruction TestTesting the Safety Sensors Fatal Injury MAY ResultRead and Follow ALL Instructions Door activationEmergency Disconnect Never GO Under a STOPPED, Partially Open DoorOperating the Wireless Wall Station Programming/Training HomeLink Unit Teaching HomeLink to the idrive openerProgramming/Training HomeLink Unit Customizing the Settings Custom pet positionMulti-Door Programming For more profile options go to page 28Maintenance Power Connection Permanent Wiring Option Reconnect PowerConfirm pot nut position* shown below Potentiometer GearStations or Transmitters to OpenerProgramming Wireless Wall Handle In Manual Door Operated Position Motor Up PositionRed Program Button Light Button Large ButtonTroubleshooting Symptom Probable Cause Corrective ActionLock Arm Troubleshooting Dalton dealer or distributor Cut-Out Template to Aid Installation Pre-drill 3/32 pilot holePre-drill 5/64 pilot hole Thank you for your purchasePatent Information Models 3790/3790-Z