Wayne-Dalton 3790-Z Installing the Light Fixture, If Included, To Avoid Electrical Shock

Page 29

	16		Installing the Light Fixture
			Installing the Light Fixture
				(If Included)

	Tools Needed:
	Tools Needed:			WARNING
	Phillips Head			WARNING
	Phillips Head	TO AVOID ELECTRICAL SHOCK
	Screwdriver	TO AVOID ELECTRICAL SHOCK
	Screwdriver	DISCONNECT POWER TO THE
		DISCONNECT POWER TO THE
	Flat Tip	RECEPTACLE AT THE FUSE/BREAKER
	Screwdriver	BOX, BEFORE PROCEEDING WITH THE
	Step Ladder	INSTALLATION OF THE LIGHT FIXTURE.
	Step Ladder

IMPORTANT! THIS LIGHT FIXTURE HAS A GROUNDING TYPE PLUG WITH A THIRD (GROUNDING) PIN. THIS PLUG WILL ONLY FIT INTO A GROUNDING-TYPE OUTLET. IF THE PLUG DOES NOT FIT INTO YOUR OUTLET, CONTACT A QUALIFIED ELECTRICIAN TO INSTALL THE PROPER GROUNDING TYPE OUTLET. DO NOT ALTER THE PLUG IN ANY WAY.

WARNING

TO AVOID ELECTRICAL SHOCK/FIRE, DO

NOT MOUNT THE LIGHT FIXTURE TO A

RECEPTACLE WITH A METAL FACE

PLATE.

IMPORTANT! GARAGE DOOR MUST

CLEAR LIGHT FIXTURE WHEN THE DOOR IS

IN THE OPEN POSITION.

The light fixture is designed to mount directly to a standard 120V duplex receptacle.

Remove the screw in the receptacle cover. Holding receptacle cover in place, insert light fixture into the receptacle that has the ground hole farthest from screw hole.

Secure light fixture to receptacle with a #6-32 x 3/4” phillips pan head screw.

Install hole plug into the screw hole in the light fixture.

NOTE: For temperature protection, the hole plug must be in place prior to using the light fixture.

Receptacle Cover

Remove Screw

#6-32 x 3/4”

Phillips Pan Head

Screw

Hole Plug

PRE-OPERATION

Please Do Not Return This Product To The Store. Call Us Directly! Our Trained Technicians Will Answer Your Questions and/or Ship Any Parts You May Need. 23 You can reach us Toll Free at 1-888-827-3667 for Consumer Assistance or online at www.wayne-dalton.com

Image 29

Contents Your Copyright 2008 Wayne-Dalton Corp. Part No Rev 2 7/16/2008Network ForPackage Contents Look for this symbol When Installing a NEW Door with AN IdriveEyes to Prevent Possible Severe or Fatal Injury Pre-InstallationInspection Tools Needed System RequirementsWAYNE-DALTON Track Radius Photoelectric LOW Head Door Models below require the use of photo eyesDeﬁnition of key words used in this manual Table of ContentsDrum Wrap & End Bracket Retro-Fit InstallationRemoval Spring Tension RemovalBracket and Gear End Bracket RemovalCenter Bracket & Cable Drum Powerful Spring Releasing ITS Retro-Fit InstallationEven Fatal Injury IMPORTANT! Right and Left Hand isRemoval End Bracket RemovalVertical Track Height Adjustment Re-Install If NecessaryTop Bracket 8000/8100/8200 TrackTracks to the Support Before Opening Door can Cause Door Top Roller AdjustmentFailure to RE-ATTACH Horizontal Assembling Opener InstallationCable Drums Secure end bracket to the flag angle using Tools Needed Power Drill Socket Driver Wrench Step LadderEnd Brackets Repeat for other end bracketCable Drum/ Drive Gear InstallationCounterbalance Springs End Bracket InstallationBrackets Support Bracket Positioning Support BracketAttaching Opener To Pliers Attaching Disconnect CableBracket Slack between opener and right endMounting Disconnect Pilot drill lag screw location using 1/8 drill bitHandle Bracket 6ftDisconnect Handle Usage Attaching Disconnect HandleSprings Cable AdjustmentsTools Needed Vice Clamps Securing DoorFor Spring Winding Hands Winding SpringsRecommended Spring Turns Drum Wrap InstallationTools Needed IMPORTANT! do not Overwind SpringsProblems Setting Spring TensionIMPORTANT! do not Overwind SCREWS. for Detailed Information onMounting Wall Station Drum Wrap InstallationInstalling Battery Disconnect Power to Installing the Light FixtureInstall hole plug into the screw hole in the light fixture If IncludedPower Cord Connecting OpenerAttaching Diffuser If IncludedSensor Unit For Proper AlignmentView of the Opener from the Front Sensor Wire InstallationChecking for Obstructions Safety Sensor AlignmentProgramming Light Fixture On when program button is pushedProfile Routine Standard Upper Limit On and remain on for 30 secondsWork Properly Adjusting DetentProfile Routine Custom Upper Limit Confirm adjustment Lock Arm InstallationTurn increments Tools Needed Tape Measure Step LadderContact Obstruction Test Lock Arm InstallationFatal Injury MAY Result Testing the Safety SensorsDoor activation Read and Follow ALL InstructionsEmergency Disconnect Never GO Under a STOPPED, Partially Open DoorOperating the Wireless Wall Station Teaching HomeLink to the idrive opener Programming/Training HomeLink UnitProgramming/Training HomeLink Unit Custom pet position Customizing the SettingsMulti-Door Programming For more profile options go to page 28Maintenance Reconnect Power Power Connection Permanent Wiring OptionConfirm pot nut position* shown below Potentiometer GearHandle In Manual Door Operated Position Motor Up Position Stations or Transmitters to OpenerProgramming Wireless WallRed Program Button Light Button Large ButtonSymptom Probable Cause Corrective Action TroubleshootingLock Arm Troubleshooting Dalton dealer or distributor Pre-drill 3/32 pilot hole Cut-Out Template to Aid InstallationPre-drill 5/64 pilot hole Thank you for your purchaseModels 3790/3790-Z Patent Information