Wayne-Dalton 3790-Z Definition of key words used in this manual, Table of Contents

Page 6

Table of Contents

Package Contents

I.

Pre-Installation Inspection

II, III

Tools Needed

IV.

Important Safety Instructions

V.

Retro-Fit Installations

1-6.

idrive® for Torquemaster® Installation

7-21.

Pre-Operation

21-32.

Operation

33-38.

Maintenance

38.

Power Connection- Permanent Wiring Option

39.

Programming Wireless Wall Station(s) or Transmitter(s) to Opener

40.

Troubleshooting

41-42.

Warranty

43.

Customer Service Number

44.

Drill Template

44.

Definition of key words used in this manual:

WARNING

INDICATES A POTENTIALLY HAZARDOUS SITUATION WHICH, IF NOT AVOIDED, COULD RESULT IN SEVERE OR FATAL INJURY.

CAUTION: PROPERTY DAMAGE OR INJURY CAN RESULT FROM FAILURE TO FOLLOW INSTRUCTIONS.

IMPORTANT: REQUIRED STEP FOR SAFE AND PROPER DOOR OPERATION.

NOTE: Information assuring proper installation of the door.

WARNING

INCORRECT INSTALLATION CAN LEAD TO SEVERE OR FATAL INJURY. FOLLOW THESE INSTRUCTIONS CAREFULLY.

IMPORTANT SAFETY INSTRUCTIONS

1.READ AND FOLLOW ALL INSTALLATION INSTRUCTIONS.

2.Do not connect the opener to electrical power until instructed to do so.

3.Install the entrapment warning label next to the wall station in a prominent location. Install the emergency disconnect label next to the emergency disconnect.

4.Remove all ropes and remove, or make inoperative in the unlocked position, all locks connected to the garage door before installing the opener.

5.Do not wear rings, watches or loose clothing when installing or servicing a garage door system.

6.It is important that you install all the components supplied with the idrive® opener, i.e., wall stations, safety sensors, etc. Use

of parts not supplied by Wayne-Dalton Corp. may cause the opener to malfunction and create unsafe conditions.

7.Wear safety glasses for eye protection when installing or servicing the opener or door.

8.Install opener on a properly balanced and operating garage door. Have a qualified service person make adjustments/repairs to cables, spring assemblies, and other hardware before installing the opener. An improperly balanced door could cause severe injury.

9.Where possible, install the opener seven feet or more above the floor. Mount the emergency disconnect six feet above the floor.

10.Locate the wall station: (a) within sight of door, (b) at a minimum height of five feet, so small children cannot reach it, and (c) away from all moving parts of the door.

11.After installing the opener, the door must reverse when it contacts a 1-1/2” high object (or 2 x 4 board laid flat) on the floor.

12.Installation and wiring must comply with local building and electrical codes. Connect the power cord to a properly grounded outlet. Do not remove the ground pin from power cord.

AFTER INSTALLATION IS COMPLETE, FASTEN THIS MANUAL NEAR GARAGE DOOR. PERFORM MONTHLY OBSTRUCTION TEST AND MAINTENANCE AS RECOMMENDED. SEE

PAGES 31, 32 AND 38.

VPlease Do Not Return This Product To The Store. Call Us Directly! Our Trained Technicians Will Answer Your Questions and/or Ship Any Parts You May Need.

You can reach us Toll Free at 1-888-827-3667 for Consumer Assistance or online at www.wayne-dalton.com

Image 6
Contents Network Copyright 2008 Wayne-Dalton Corp. Part No Rev 2 7/16/2008Your ForPackage Contents When Installing a NEW Door with AN Idrive Look for this symbolPre-Installation InspectionEyes to Prevent Possible Severe or Fatal Injury WAYNE-DALTON Track Radius Photoelectric LOW Head System RequirementsTools Needed Door Models below require the use of photo eyesTable of Contents Definition of key words used in this manualRemoval Retro-Fit InstallationDrum Wrap & End Bracket Spring Tension RemovalEnd Bracket Removal Center Bracket & Cable DrumBracket and Gear Even Fatal Injury Retro-Fit InstallationPowerful Spring Releasing ITS IMPORTANT! Right and Left Hand isEnd Bracket Removal RemovalTop Bracket Re-Install If NecessaryVertical Track Height Adjustment 8000/8100/8200 TrackTop Roller Adjustment Failure to RE-ATTACH HorizontalTracks to the Support Before Opening Door can Cause Door Installation Assembling OpenerCable Drums End Brackets Tools Needed Power Drill Socket Driver Wrench Step LadderSecure end bracket to the flag angle using Repeat for other end bracketInstallation Cable Drum/ Drive GearEnd Bracket Installation BracketsCounterbalance Springs Positioning Support Bracket Attaching Opener ToSupport Bracket Bracket Attaching Disconnect CablePliers Slack between opener and right endHandle Bracket Pilot drill lag screw location using 1/8 drill bitMounting Disconnect 6ftAttaching Disconnect Handle Disconnect Handle UsageCable Adjustments SpringsSecuring Door For Spring WindingTools Needed Vice Clamps Winding Springs HandsTools Needed Drum Wrap InstallationRecommended Spring Turns IMPORTANT! do not Overwind SpringsIMPORTANT! do not Overwind Setting Spring TensionProblems SCREWS. for Detailed Information onDrum Wrap Installation Mounting Wall StationInstalling Battery Install hole plug into the screw hole in the light fixture Installing the Light FixtureDisconnect Power to If IncludedAttaching Diffuser Connecting OpenerPower Cord If IncludedFor Proper Alignment Sensor UnitSensor Wire Installation View of the Opener from the FrontSafety Sensor Alignment Checking for ObstructionsProfile Routine Standard Upper Limit On when program button is pushedProgramming Light Fixture On and remain on for 30 secondsAdjusting Detent Profile Routine Custom Upper LimitWork Properly Turn increments Lock Arm InstallationConfirm adjustment Tools Needed Tape Measure Step LadderLock Arm Installation Contact Obstruction TestTesting the Safety Sensors Fatal Injury MAY ResultEmergency Disconnect Read and Follow ALL InstructionsDoor activation Never GO Under a STOPPED, Partially Open DoorOperating the Wireless Wall Station Programming/Training HomeLink Unit Teaching HomeLink to the idrive openerProgramming/Training HomeLink Unit Multi-Door Programming Customizing the SettingsCustom pet position For more profile options go to page 28Maintenance Confirm pot nut position* shown below Power Connection Permanent Wiring OptionReconnect Power Potentiometer GearRed Program Button Stations or Transmitters to OpenerProgramming Wireless WallHandle In Manual Door Operated Position Motor Up Position Light Button Large ButtonTroubleshooting Symptom Probable Cause Corrective ActionLock Arm Troubleshooting Dalton dealer or distributor Pre-drill 5/64 pilot hole Cut-Out Template to Aid InstallationPre-drill 3/32 pilot hole Thank you for your purchasePatent Information Models 3790/3790-Z