Wayne-Dalton 3790-Z Attaching Diffuser, If Included, Connecting Opener, Power Cord

Page 30

17

Attaching Diffuser

Power Outlet

(If Included)

Light Fixture

 

Tools Needed:

Screw a 75W (maximum) light bulb into

Mating Slots

Step Ladder

light socket and snap diffuser into light

fixture.

 

 

 

 

When assembling diffuser, make sure all

 

 

three snap tabs are aligned and fully

Light Socket

 

snapped into the three mating slots of the

 

 

light fixture.

 

 

Turn receptacle power back on at fuse/

75W (MAX)

 

Light Bulb

 

breaker box. The light should blink one

(Not Included)

 

time when the power is turned back on.

Snap Tabs

NOTE: An accessory power outlet receptacle (600 Watt Maximum) is provided as part of the light fixture.

 

 

 

 

 

Diffuser

18

Connecting Opener

(Ceiling)

 

 

Cable Clips

 

 

 

 

 

 

 

 

Power Cord

 

 

 

 

 

 

 

 

Tools Needed:

WARNING

 

 

 

 

Phillips Head

TO REDUCE THE RISK OF ELECTRICAL

 

 

 

 

Screwdriver

SHOCK, DO NOT CHANGE THE POWER

 

 

 

#6 x 7/8

Step Ladder

CORD PLUG IN ANYWAY.

Plug Into Nearest

 

 

Wood Screws

Power Outlet

 

 

 

 

 

 

 

 

The opener can be permanently wired. To

 

 

 

 

 

permanently wire the unit, see Permanent

 

 

Controls

 

 

Wiring option on page 39.

Z-Wave enabled

 

 

 

 

 

Learn S1

S2

S3 S4

Delete

 

 

what’s

 

 

 

 

 

OPENING

 

 

 

 

Plug the end of the power cord into the

your world?

 

 

 

 

thermostatandstart

 

 

 

 

 

®

 

 

 

 

 

WithZ-Wave

 

 

 

 

 

technology you can

 

 

 

 

 

controlyourlights,

 

 

 

 

closest grounding type receptacle

yourmorning coffee,

 

 

 

 

allwiththe single

 

 

 

 

touch ofabutton.

 

 

 

 

Otherwise, contact a service person for

 

 

 

 

 

further options. Excess power cord length

 

 

 

 

 

must be routed and contained safely away

 

 

 

 

 

from any moving parts.

 

 

 

 

 

As soon as power is applied to the opener,

 

 

 

Disconnect

 

 

 

 

Cable

 

it should beep two times.

 

 

 

 

 

 

 

 

 

NOTE: Do not permanently attach power

 

 

 

 

 

cord to building!

 

 

 

 

 

NOTE: Use only the flexible cable clips

 

 

 

 

 

supplied with the opener.

 

 

 

 

 

 

 

 

 

Power Cord

 

 

 

 

 

No Interference

 

 

 

 

 

Between Power

 

 

 

 

 

Cord and

 

 

 

 

 

Disconnect Cable

24Please Do Not Return This Product To The Store. Call Us Directly! Our Trained Technicians Will Answer Your Questions and/or Ship Any Parts You May Need.

You can reach us Toll Free at 1-888-827-3667 for Consumer Assistance or online at www.wayne-dalton.com

Image 30
Contents Network Copyright 2008 Wayne-Dalton Corp. Part No Rev 2 7/16/2008Your ForPackage Contents When Installing a NEW Door with AN Idrive Look for this symbolPre-Installation InspectionEyes to Prevent Possible Severe or Fatal Injury WAYNE-DALTON Track Radius Photoelectric LOW Head System RequirementsTools Needed Door Models below require the use of photo eyesTable of Contents Definition of key words used in this manualRemoval Retro-Fit InstallationDrum Wrap & End Bracket Spring Tension RemovalEnd Bracket Removal Center Bracket & Cable DrumBracket and Gear Even Fatal Injury Retro-Fit InstallationPowerful Spring Releasing ITS IMPORTANT! Right and Left Hand isEnd Bracket Removal RemovalTop Bracket Re-Install If NecessaryVertical Track Height Adjustment 8000/8100/8200 TrackTop Roller Adjustment Failure to RE-ATTACH HorizontalTracks to the Support Before Opening Door can Cause Door Installation Assembling OpenerCable Drums End Brackets Tools Needed Power Drill Socket Driver Wrench Step LadderSecure end bracket to the flag angle using Repeat for other end bracketInstallation Cable Drum/ Drive GearEnd Bracket Installation BracketsCounterbalance Springs Positioning Support Bracket Attaching Opener ToSupport Bracket Bracket Attaching Disconnect CablePliers Slack between opener and right endHandle Bracket Pilot drill lag screw location using 1/8 drill bitMounting Disconnect 6ftAttaching Disconnect Handle Disconnect Handle UsageCable Adjustments SpringsSecuring Door For Spring WindingTools Needed Vice Clamps Winding Springs HandsTools Needed Drum Wrap InstallationRecommended Spring Turns IMPORTANT! do not Overwind SpringsIMPORTANT! do not Overwind Setting Spring TensionProblems SCREWS. for Detailed Information onDrum Wrap Installation Mounting Wall StationInstalling Battery Install hole plug into the screw hole in the light fixture Installing the Light FixtureDisconnect Power to If IncludedAttaching Diffuser Connecting OpenerPower Cord If IncludedFor Proper Alignment Sensor UnitSensor Wire Installation View of the Opener from the FrontSafety Sensor Alignment Checking for ObstructionsProfile Routine Standard Upper Limit On when program button is pushedProgramming Light Fixture On and remain on for 30 secondsAdjusting Detent Profile Routine Custom Upper LimitWork Properly Turn increments Lock Arm InstallationConfirm adjustment Tools Needed Tape Measure Step LadderLock Arm Installation Contact Obstruction TestTesting the Safety Sensors Fatal Injury MAY ResultEmergency Disconnect Read and Follow ALL InstructionsDoor activation Never GO Under a STOPPED, Partially Open DoorOperating the Wireless Wall Station Programming/Training HomeLink Unit Teaching HomeLink to the idrive openerProgramming/Training HomeLink Unit Multi-Door Programming Customizing the SettingsCustom pet position For more profile options go to page 28Maintenance Confirm pot nut position* shown below Power Connection Permanent Wiring OptionReconnect Power Potentiometer GearRed Program Button Stations or Transmitters to OpenerProgramming Wireless WallHandle In Manual Door Operated Position Motor Up Position Light Button Large ButtonTroubleshooting Symptom Probable Cause Corrective ActionLock Arm Troubleshooting Dalton dealer or distributor Pre-drill 5/64 pilot hole Cut-Out Template to Aid InstallationPre-drill 3/32 pilot hole Thank you for your purchasePatent Information Models 3790/3790-Z