Wayne-Dalton 3790 Pre-drill 3/32 pilot hole, Pre-drill 5/64 pilot hole, Wall Station Template

Page 50

✁	Cut-Out Template to Aid Installation

Pre-drill 3/32” pilot hole

Pre-drill 5/64” pilot hole

Wall Station Template

Keyless Entry Template

Please Do Not Return This Product To The Store

Call Us Directly! Our Trained Technicians Will Answer Your Questions and /or Ship Any Parts You May Need

Call Us Toll-Free: (888) 827-3667

Thank you for your purchase

www.wayne-dalton.com

44Please Do Not Return This Product To The Store. Call Us Directly! Our Trained Technicians Will Answer Your Questions and/or Ship Any Parts You May Need.

You can reach us Toll Free at 1-888-827-3667 for Consumer Assistance or online at www.wayne-dalton.com

Image 50

Contents Network Copyright 2008 Wayne-Dalton Corp. Part No Rev 2 7/16/2008Your ForPackage Contents When Installing a NEW Door with AN Idrive Look for this symbolEyes to Prevent Possible Severe or Fatal Injury Pre-InstallationInspection WAYNE-DALTON Track Radius Photoelectric LOW Head System RequirementsTools Needed Door Models below require the use of photo eyesTable of Contents Deﬁnition of key words used in this manualRemoval Retro-Fit InstallationDrum Wrap & End Bracket Spring Tension RemovalBracket and Gear End Bracket RemovalCenter Bracket & Cable Drum Even Fatal Injury Retro-Fit InstallationPowerful Spring Releasing ITS IMPORTANT! Right and Left Hand isEnd Bracket Removal RemovalTop Bracket Re-Install If NecessaryVertical Track Height Adjustment 8000/8100/8200 TrackTracks to the Support Before Opening Door can Cause Door Top Roller AdjustmentFailure to RE-ATTACH Horizontal Installation Assembling OpenerCable Drums End Brackets Tools Needed Power Drill Socket Driver Wrench Step LadderSecure end bracket to the flag angle using Repeat for other end bracketInstallation Cable Drum/ Drive GearCounterbalance Springs End Bracket InstallationBrackets Support Bracket Positioning Support BracketAttaching Opener To Bracket Attaching Disconnect CablePliers Slack between opener and right endHandle Bracket Pilot drill lag screw location using 1/8 drill bitMounting Disconnect 6ftAttaching Disconnect Handle Disconnect Handle UsageCable Adjustments SpringsTools Needed Vice Clamps Securing DoorFor Spring Winding Winding Springs HandsTools Needed Drum Wrap InstallationRecommended Spring Turns IMPORTANT! do not Overwind SpringsIMPORTANT! do not Overwind Setting Spring TensionProblems SCREWS. for Detailed Information onDrum Wrap Installation Mounting Wall StationInstalling Battery Install hole plug into the screw hole in the light fixture Installing the Light FixtureDisconnect Power to If IncludedAttaching Diffuser Connecting OpenerPower Cord If IncludedFor Proper Alignment Sensor UnitSensor Wire Installation View of the Opener from the FrontSafety Sensor Alignment Checking for ObstructionsProfile Routine Standard Upper Limit On when program button is pushedProgramming Light Fixture On and remain on for 30 secondsWork Properly Adjusting DetentProfile Routine Custom Upper Limit Turn increments Lock Arm InstallationConfirm adjustment Tools Needed Tape Measure Step LadderLock Arm Installation Contact Obstruction TestTesting the Safety Sensors Fatal Injury MAY ResultEmergency Disconnect Read and Follow ALL InstructionsDoor activation Never GO Under a STOPPED, Partially Open DoorOperating the Wireless Wall Station Programming/Training HomeLink Unit Teaching HomeLink to the idrive openerProgramming/Training HomeLink Unit Multi-Door Programming Customizing the SettingsCustom pet position For more profile options go to page 28Maintenance Confirm pot nut position* shown below Power Connection Permanent Wiring OptionReconnect Power Potentiometer GearRed Program Button Stations or Transmitters to OpenerProgramming Wireless WallHandle In Manual Door Operated Position Motor Up Position Light Button Large ButtonTroubleshooting Symptom Probable Cause Corrective ActionLock Arm Troubleshooting Dalton dealer or distributor Pre-drill 5/64 pilot hole Cut-Out Template to Aid InstallationPre-drill 3/32 pilot hole Thank you for your purchasePatent Information Models 3790/3790-Z