Wayne-Dalton 3790-Z When Installing a NEW Door with AN Idrive, Look for this symbol

Page 3

PRE-INSTALLATION INSPECTION OF YOUR GARAGE DOOR

PRIOR TO TORQUEMASTER® IDRIVE® INSTALLATION

Congratulations, you have just purchased one of the world’s safest garage door openers! By design, this opener will detect obstructions and reverse rather than force the door through

obstructions. To ensure your new idrive® opener works as intended, your garage door must be installed and balanced properly.

WHEN INSTALLING A NEW DOOR WITH AN IDRIVE®:

If you just finished installing a new garage door along with an idrive® opener, then proceed with these instructions beginning with Step 14 on page 21. If you were referred to these instructions as part of a new door installation, then proceed with these instructions beginning with Step 1 on page 7.

WHEN INSTALLING AN IDRIVE® ON AN EXISTING DOOR WITH TORQUEMASTER® OR

TORQUEMASTER® PLUS:

Before installing the idrive® opener, open and close you door manually to ensure that it operates smoothly from top to bottom. A properly balanced door should not take a lot of effort to open or close by hand. The door should stay in the open and in the closed position without drifting down or creeping up. If a door opens fast going up, the door may need spring tension reduced. If the door drops fast going down, the door may need spring tension increased.

If the operation of the door does not meet these criteria, you need to adjust the spring balance per your door’s Installation Instructions and Owner’s Manual or call a professional installer to make adjustments before installing idrive®.

If the door operates properly, check and record your Torquemaster® counterbalance spring settings (for Torquemaster Plus spring settings, see warning tag(s) attached to the end brackets or refer to your door Installation Instructions and Owner’s manual). Then proceed with unwinding of the spring(s) for installation of your idrive®, carefully following the instructions in the appropriate STEP R1 of your idrive® Installation Instructions and Owner’s Manual. After the idrive® is installed on the Torquemaster® tube, rewind the Torquemaster® or Torquemaster® Plus to the previously recorded settings.

Instruction manuals are available for download on www.wayne-dalton.com.Use the web site to also find the location of your nearest professional dealer.

Check out the new idrive® installation video at www.wayne-dalton.com

idrive® for Torquemaster®

 

®

http://www.wayne-dalton.com/idrive_TorqueMaster.asp

 

 

 

 

 

 

Look for this symbol.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Please Do Not Return This Product To The Store. Call Us Directly! Our Trained Technicians Will Answer Your Questions and/or Ship Any Parts You May Need.

II

You can reach us Toll Free at 1-888-827-3667 for Consumer Assistance or online at www.wayne-dalton.com

 

Page 2 Page 4
Image 3
Page 2 Page 4
Contents For Copyright 2008 Wayne-Dalton Corp. Part No Rev 2 7/16/2008Your NetworkPackage Contents Look for this symbol When Installing a NEW Door with AN IdrivePre-Installation InspectionEyes to Prevent Possible Severe or Fatal Injury Door Models below require the use of photo eyes System RequirementsTools Needed WAYNE-DALTON Track Radius Photoelectric LOW HeadDefinition of key words used in this manual Table of ContentsSpring Tension Removal Retro-Fit InstallationDrum Wrap & End Bracket RemovalEnd Bracket Removal Center Bracket & Cable DrumBracket and Gear IMPORTANT! Right and Left Hand is Retro-Fit InstallationPowerful Spring Releasing ITS Even Fatal InjuryRemoval End Bracket Removal8000/8100/8200 Track Re-Install If NecessaryVertical Track Height Adjustment Top BracketTop Roller Adjustment Failure to RE-ATTACH HorizontalTracks to the Support Before Opening Door can Cause Door Assembling Opener InstallationCable Drums Repeat for other end bracket Tools Needed Power Drill Socket Driver Wrench Step LadderSecure end bracket to the flag angle using End BracketsCable Drum/ Drive Gear InstallationEnd Bracket Installation BracketsCounterbalance Springs Positioning Support Bracket Attaching Opener ToSupport Bracket Slack between opener and right end Attaching Disconnect CablePliers Bracket6ft Pilot drill lag screw location using 1/8 drill bitMounting Disconnect Handle BracketDisconnect Handle Usage Attaching Disconnect HandleSprings Cable AdjustmentsSecuring Door For Spring WindingTools Needed Vice Clamps Hands Winding SpringsIMPORTANT! do not Overwind Springs Drum Wrap InstallationRecommended Spring Turns Tools NeededSCREWS. for Detailed Information on Setting Spring TensionProblems IMPORTANT! do not OverwindMounting Wall Station Drum Wrap InstallationInstalling Battery If Included Installing the Light FixtureDisconnect Power to Install hole plug into the screw hole in the light fixtureIf Included Connecting OpenerPower Cord Attaching DiffuserSensor Unit For Proper AlignmentView of the Opener from the Front Sensor Wire InstallationChecking for Obstructions Safety Sensor AlignmentOn and remain on for 30 seconds On when program button is pushedProgramming Light Fixture Profile Routine Standard Upper LimitAdjusting Detent Profile Routine Custom Upper LimitWork Properly Tools Needed Tape Measure Step Ladder Lock Arm InstallationConfirm adjustment Turn incrementsContact Obstruction Test Lock Arm InstallationFatal Injury MAY Result Testing the Safety SensorsNever GO Under a STOPPED, Partially Open Door Read and Follow ALL InstructionsDoor activation Emergency DisconnectOperating the Wireless Wall Station Teaching HomeLink to the idrive opener Programming/Training HomeLink UnitProgramming/Training HomeLink Unit For more profile options go to page 28 Customizing the SettingsCustom pet position Multi-Door ProgrammingMaintenance Potentiometer Gear Power Connection Permanent Wiring OptionReconnect Power Confirm pot nut position* shown belowLight Button Large Button Stations or Transmitters to OpenerProgramming Wireless WallHandle In Manual Door Operated Position Motor Up Position Red Program ButtonSymptom Probable Cause Corrective Action TroubleshootingLock Arm Troubleshooting Dalton dealer or distributor Thank you for your purchase Cut-Out Template to Aid InstallationPre-drill 3/32 pilot hole Pre-drill 5/64 pilot holeModels 3790/3790-Z Patent Information
Top Page Image Contents