Wayne-Dalton 3790-Z Programming Light Fixture, Profile Routine Standard Upper Limit

Page 34

	23	Programming Light Fixture
		Programming Light Fixture
		(If Included)

	Tools Needed:	Press the red program button on the light
	Step Ladder	fixture. The LED on the light fixture will turn
	Step Ladder	on and remain on for 30 seconds
		on and remain on for 30 seconds
		or until a opener is learned to the light
		fixture. The incandescent lamp will also turn
		on when program button is pushed.
		Press the light button on the wall station.
		This must be done within 30 seconds of
		pressing the program button on the light
		fixture. The light fixture lamp and LED will
		blink three times to indicate successful
		programming. The light fixture can now be
		turned on and off from this wall station.
		NOTE: In order to program the opener to
		the light fixture, the installer must have the
		wall station already programmed to the
		opener.

Program Button LED

Light Button

per
O	at
o	e
T	D
Press
	o
	o
	Here	r
		r

24

Tools Needed:

None

Profile Routine

(Standard Upper Limit)

WARNING

TO AVOID INJURY, NO ONE SHOULD CROSS THE PATH OF A MOVING DOOR!

The profile routine automatically sets the door open and close limits and calibrates obstruction sensing. During the profile routine, the door will move up and down twice.

NOTE: If an object such as a ceiling beam obstructs the door from opening completely, skip this step. Set a Custom Upper Limit, see Step 25.

NOTE: The door must be in its fully closed position and the disconnect handle must be in the motor operated position (upper position) to initiate the profile routine.

NOTE: Profile routine will not run if safety sensors are not aligned (only if required installation).

Press and hold the profile button for five (5) seconds. The opener will beep twice, release the profile button, indicating the activation of the profile routine. The door will now move to the fully open position and stop, beep twice and then the door will close completely.

Next, the door will go through one more up/ down cycle. Once this is complete, the door limits are set and the profile is complete.

NOTE: Upon successful completion proceed to Step 26.

Profile Button

28Please Do Not Return This Product To The Store. Call Us Directly! Our Trained Technicians Will Answer Your Questions and/or Ship Any Parts You May Need.

You can reach us Toll Free at 1-888-827-3667 for Consumer Assistance or online at www.wayne-dalton.com

Image 34

Contents Network Copyright 2008 Wayne-Dalton Corp. Part No Rev 2 7/16/2008Your ForPackage Contents When Installing a NEW Door with AN Idrive Look for this symbolInspection Pre-InstallationEyes to Prevent Possible Severe or Fatal Injury WAYNE-DALTON Track Radius Photoelectric LOW Head System RequirementsTools Needed Door Models below require the use of photo eyesTable of Contents Deﬁnition of key words used in this manualRemoval Retro-Fit InstallationDrum Wrap & End Bracket Spring Tension RemovalCenter Bracket & Cable Drum End Bracket RemovalBracket and Gear Even Fatal Injury Retro-Fit InstallationPowerful Spring Releasing ITS IMPORTANT! Right and Left Hand isEnd Bracket Removal RemovalTop Bracket Re-Install If NecessaryVertical Track Height Adjustment 8000/8100/8200 TrackFailure to RE-ATTACH Horizontal Top Roller AdjustmentTracks to the Support Before Opening Door can Cause Door Installation Assembling OpenerCable Drums End Brackets Tools Needed Power Drill Socket Driver Wrench Step LadderSecure end bracket to the flag angle using Repeat for other end bracketInstallation Cable Drum/ Drive GearBrackets End Bracket InstallationCounterbalance Springs Attaching Opener To Positioning Support BracketSupport Bracket Bracket Attaching Disconnect CablePliers Slack between opener and right endHandle Bracket Pilot drill lag screw location using 1/8 drill bitMounting Disconnect 6ftAttaching Disconnect Handle Disconnect Handle UsageCable Adjustments SpringsFor Spring Winding Securing DoorTools Needed Vice Clamps Winding Springs HandsTools Needed Drum Wrap InstallationRecommended Spring Turns IMPORTANT! do not Overwind SpringsIMPORTANT! do not Overwind Setting Spring TensionProblems SCREWS. for Detailed Information onDrum Wrap Installation Mounting Wall StationInstalling Battery Install hole plug into the screw hole in the light fixture Installing the Light FixtureDisconnect Power to If IncludedAttaching Diffuser Connecting OpenerPower Cord If IncludedFor Proper Alignment Sensor UnitSensor Wire Installation View of the Opener from the FrontSafety Sensor Alignment Checking for ObstructionsProfile Routine Standard Upper Limit On when program button is pushedProgramming Light Fixture On and remain on for 30 secondsProfile Routine Custom Upper Limit Adjusting DetentWork Properly Turn increments Lock Arm InstallationConfirm adjustment Tools Needed Tape Measure Step LadderLock Arm Installation Contact Obstruction TestTesting the Safety Sensors Fatal Injury MAY ResultEmergency Disconnect Read and Follow ALL InstructionsDoor activation Never GO Under a STOPPED, Partially Open DoorOperating the Wireless Wall Station Programming/Training HomeLink Unit Teaching HomeLink to the idrive openerProgramming/Training HomeLink Unit Multi-Door Programming Customizing the SettingsCustom pet position For more profile options go to page 28Maintenance Confirm pot nut position* shown below Power Connection Permanent Wiring OptionReconnect Power Potentiometer GearRed Program Button Stations or Transmitters to OpenerProgramming Wireless WallHandle In Manual Door Operated Position Motor Up Position Light Button Large ButtonTroubleshooting Symptom Probable Cause Corrective ActionLock Arm Troubleshooting Dalton dealer or distributor Pre-drill 5/64 pilot hole Cut-Out Template to Aid InstallationPre-drill 3/32 pilot hole Thank you for your purchasePatent Information Models 3790/3790-Z