Wayne-Dalton 3790-Z installation instructions Programming/Training HomeLink Unit

Page 42

❉

Programming HomeLink® System to the Torquemaster® idrive® (Alternate)

 

NOTE: This Step can only be done on automobiles equipped with the HomeLink® system.

NOTE: Programming HomeLink® requires a Wayne-Dalton Transmitter that is programmed to the opener (the wallstation and transmitter(s) supplied with the opener, come pre-programmed from the factory). Any additional wallstation(s) or transmitter(s) will need to be programmed to the opener, see page 40.

IMPORTANT! Use the programming instructions provided with your vehicle first. Follow these instructions if the HomeLink® unit does not learn the transmitter, when using the vehicle’s instructions.

NOTE: Vehicle may need to be in accessory position when programming. Check car owner’s manual.

NOTE: HomeLink® is a registered trademark of Johnson Controls.

Programming/Training HomeLink® Unit

WARNING

GARAGE DOOR MAY OPERATE DURING PROGRAMMING. TO AVOID POSSIBLE SEVERE OR FATAL INJURY, PLACE THE EMERGENCY DISCONNECT HANDLE IN THE MANUAL OPERATED POSITION.

1.Pull the manual disconnect to put the opener in the disengaged position.

2.Press and hold the two outside buttons on the HomeLink®

unit until the HomeLink® light begins to flash rapidly (approx. 20 seconds), then release both buttons. (Do not perform this step to train additional hand-held transmitters.) NOTE: This operation erases all previously learned transmitters and that you need to re-teach any other transmitters to your HomeLink® unit by repeating steps 3 - 6 below.

3.Hold the end of the Wayne®Dalton hand-held transmitter approximately 1 to 3 inches away from the HomeLink® surface – keeping the HomeLink® indicator light in view.

4.Use the large button on the Wayne Dalton transmitter. Simultaneously press and hold desired Homelink® button and the Wayne Dalton transmitter large button. Continue to press both buttons counting LED flashes on the HomeLink® module; between 50 to 60 LED flashes the LED will either come on solid or do one “quick flash”; when either of these occur release both Wayne Dalton transmitter and HomeLink® buttons.

Teaching HomeLink® to the idrive® Opener

5.Press and release the red program button on the idrive® opener. The idrive® unit will beep, indicating that it is ready to learn.

NOTE: The idrive® will remain in the learn mode for 30 seconds.

6.Press the HomeLink® button used in Step 4 above for 1 to 3 seconds. The idrive® will beep indicating a successful learn.

7.Return the manual disconnect to the engaged position.

8.Press the HomeLink® button once more to operate the door.

NOTE: The first transmitter command after programming will only move the door through a six inch up/down cycle. Normal door operations will occur on the second use of the transmitter.

36Please Do Not Return This Product To The Store. Call Us Directly! Our Trained Technicians Will Answer Your Questions and/or Ship Any Parts You May Need.

You can reach us Toll Free at 1-888-827-3667 for Consumer Assistance or online at www.wayne-dalton.com

Page 41 Page 43
Image 42
Page 41 Page 43
Contents Network Copyright 2008 Wayne-Dalton Corp. Part No Rev 2 7/16/2008Your ForPackage Contents When Installing a NEW Door with AN Idrive Look for this symbolPre-Installation InspectionEyes to Prevent Possible Severe or Fatal Injury WAYNE-DALTON Track Radius Photoelectric LOW Head System RequirementsTools Needed Door Models below require the use of photo eyesTable of Contents Definition of key words used in this manualRemoval Retro-Fit InstallationDrum Wrap & End Bracket Spring Tension RemovalEnd Bracket Removal Center Bracket & Cable DrumBracket and Gear Even Fatal Injury Retro-Fit InstallationPowerful Spring Releasing ITS IMPORTANT! Right and Left Hand isEnd Bracket Removal RemovalTop Bracket Re-Install If NecessaryVertical Track Height Adjustment 8000/8100/8200 TrackTop Roller Adjustment Failure to RE-ATTACH HorizontalTracks to the Support Before Opening Door can Cause Door Installation Assembling OpenerCable Drums End Brackets Tools Needed Power Drill Socket Driver Wrench Step LadderSecure end bracket to the flag angle using Repeat for other end bracketInstallation Cable Drum/ Drive GearEnd Bracket Installation BracketsCounterbalance Springs Positioning Support Bracket Attaching Opener ToSupport Bracket Bracket Attaching Disconnect CablePliers Slack between opener and right endHandle Bracket Pilot drill lag screw location using 1/8 drill bitMounting Disconnect 6ftAttaching Disconnect Handle Disconnect Handle UsageCable Adjustments SpringsSecuring Door For Spring WindingTools Needed Vice Clamps Winding Springs HandsTools Needed Drum Wrap InstallationRecommended Spring Turns IMPORTANT! do not Overwind SpringsIMPORTANT! do not Overwind Setting Spring TensionProblems SCREWS. for Detailed Information onDrum Wrap Installation Mounting Wall StationInstalling Battery Install hole plug into the screw hole in the light fixture Installing the Light FixtureDisconnect Power to If IncludedAttaching Diffuser Connecting OpenerPower Cord If IncludedFor Proper Alignment Sensor UnitSensor Wire Installation View of the Opener from the FrontSafety Sensor Alignment Checking for ObstructionsProfile Routine Standard Upper Limit On when program button is pushedProgramming Light Fixture On and remain on for 30 secondsAdjusting Detent Profile Routine Custom Upper LimitWork Properly Turn increments Lock Arm InstallationConfirm adjustment Tools Needed Tape Measure Step LadderLock Arm Installation Contact Obstruction TestTesting the Safety Sensors Fatal Injury MAY ResultEmergency Disconnect Read and Follow ALL InstructionsDoor activation Never GO Under a STOPPED, Partially Open DoorOperating the Wireless Wall Station Programming/Training HomeLink Unit Teaching HomeLink to the idrive openerProgramming/Training HomeLink Unit Multi-Door Programming Customizing the SettingsCustom pet position For more profile options go to page 28Maintenance Confirm pot nut position* shown below Power Connection Permanent Wiring OptionReconnect Power Potentiometer GearRed Program Button Stations or Transmitters to OpenerProgramming Wireless WallHandle In Manual Door Operated Position Motor Up Position Light Button Large ButtonTroubleshooting Symptom Probable Cause Corrective ActionLock Arm Troubleshooting Dalton dealer or distributor Pre-drill 5/64 pilot hole Cut-Out Template to Aid InstallationPre-drill 3/32 pilot hole Thank you for your purchasePatent Information Models 3790/3790-Z
Top Page Image Contents