Wayne-Dalton 3790-Z installation instructions Drum Wrap Installation, Mounting Wall Station

Page 27

13

Drum Wrap Installation

Drum

 

 

Tools Needed:

Drum wraps (supplied with Torquemaster®

Wrap

 

Step Ladder

counterbalance systems) are identified as

Outside

right and left.

 

Flange

 

To install, place the drum wrap over the

 

 

cable drum and under the idrive®

 

 

disconnect cable. Align the outside flange

 

 

over the outside edge of the cable drum

 

 

and push the drum wrap down onto the

Cable

 

cable drum.

Drum

 

 

Drum

 

 

Wrap

 

 

®INSTALLATION

 

 

Cable

 

 

Drum

14

Mounting Wall Station

TORQUEMASTER

 

 

 

Tools Needed:

WARNING

FOR

Tape Measure

TO PREVENT POSSIBLE INJURY, INSTALL

Power Drill

WALL STATION OUT OF THE REACH OF

®

CHILDREN AND IN A LOCATION WHERE

IDRIVE

3/16” or

 

THE DOOR CAN BE SEEN WHEN THE

 

3/32" Drill Bit

OPENER IS ACTIVATED. DO NOT MOUNT

 

Phillips Head

WALL STATION NEAR OR NEXT TO

 

GARAGE DOOR.

 

Screwdriver

 

 

 

NOTE: For proper operation, mount the wall station on a flat surface.

The wall station can be mounted to a NEMA

 

standard electrical device box or directly to

5’ Min

any wall surface. No wiring is required.

 

Select appropriate place to mount wall station. To keep wall station out of the reach of children, locate it at least five feet up from the floor.

Please Do Not Return This Product To The Store. Call Us Directly! Our Trained Technicians Will Answer Your Questions and/or Ship Any Parts You May Need. 21 You can reach us Toll Free at 1-888-827-3667 for Consumer Assistance or online at www.wayne-dalton.com

Page 26 Page 28
Image 27
Page 26 Page 28
Contents For Copyright 2008 Wayne-Dalton Corp. Part No Rev 2 7/16/2008Your NetworkPackage Contents Look for this symbol When Installing a NEW Door with AN IdrivePre-Installation InspectionEyes to Prevent Possible Severe or Fatal Injury Door Models below require the use of photo eyes System RequirementsTools Needed WAYNE-DALTON Track Radius Photoelectric LOW HeadDefinition of key words used in this manual Table of ContentsSpring Tension Removal Retro-Fit InstallationDrum Wrap & End Bracket RemovalEnd Bracket Removal Center Bracket & Cable DrumBracket and Gear IMPORTANT! Right and Left Hand is Retro-Fit InstallationPowerful Spring Releasing ITS Even Fatal InjuryRemoval End Bracket Removal8000/8100/8200 Track Re-Install If NecessaryVertical Track Height Adjustment Top BracketTop Roller Adjustment Failure to RE-ATTACH HorizontalTracks to the Support Before Opening Door can Cause Door Assembling Opener InstallationCable Drums Repeat for other end bracket Tools Needed Power Drill Socket Driver Wrench Step LadderSecure end bracket to the flag angle using End BracketsCable Drum/ Drive Gear InstallationEnd Bracket Installation BracketsCounterbalance Springs Positioning Support Bracket Attaching Opener ToSupport Bracket Slack between opener and right end Attaching Disconnect CablePliers Bracket6ft Pilot drill lag screw location using 1/8 drill bitMounting Disconnect Handle BracketDisconnect Handle Usage Attaching Disconnect HandleSprings Cable AdjustmentsSecuring Door For Spring WindingTools Needed Vice Clamps Hands Winding SpringsIMPORTANT! do not Overwind Springs Drum Wrap InstallationRecommended Spring Turns Tools NeededSCREWS. for Detailed Information on Setting Spring TensionProblems IMPORTANT! do not OverwindMounting Wall Station Drum Wrap InstallationInstalling Battery If Included Installing the Light FixtureDisconnect Power to Install hole plug into the screw hole in the light fixtureIf Included Connecting OpenerPower Cord Attaching DiffuserSensor Unit For Proper AlignmentView of the Opener from the Front Sensor Wire InstallationChecking for Obstructions Safety Sensor AlignmentOn and remain on for 30 seconds On when program button is pushedProgramming Light Fixture Profile Routine Standard Upper LimitAdjusting Detent Profile Routine Custom Upper LimitWork Properly Tools Needed Tape Measure Step Ladder Lock Arm InstallationConfirm adjustment Turn incrementsContact Obstruction Test Lock Arm InstallationFatal Injury MAY Result Testing the Safety SensorsNever GO Under a STOPPED, Partially Open Door Read and Follow ALL InstructionsDoor activation Emergency DisconnectOperating the Wireless Wall Station Teaching HomeLink to the idrive opener Programming/Training HomeLink UnitProgramming/Training HomeLink Unit For more profile options go to page 28 Customizing the SettingsCustom pet position Multi-Door ProgrammingMaintenance Potentiometer Gear Power Connection Permanent Wiring OptionReconnect Power Confirm pot nut position* shown belowLight Button Large Button Stations or Transmitters to OpenerProgramming Wireless WallHandle In Manual Door Operated Position Motor Up Position Red Program ButtonSymptom Probable Cause Corrective Action TroubleshootingLock Arm Troubleshooting Dalton dealer or distributor Thank you for your purchase Cut-Out Template to Aid InstallationPre-drill 3/32 pilot hole Pre-drill 5/64 pilot holeModels 3790/3790-Z Patent Information
Top Page Image Contents