Wayne-Dalton 3790-Z Power Connection Permanent Wiring Option, Reconnect Power, Potentiometer Gear

Page 45

❉

Power Connection — Permanent Wiring Option

 

If required by local codes, the opener can be permanently wired. Services of a licensed electrician should be obtained, to permanently wire the Unit. Disconnect electrical power at fuse/breaker box.

WARNING

TO AVOID ELECTRICAL SHOCK, DISCONNECT POWER AT FUSE/ BREAKER BOX BEFORE PROCEEDING.

a. Using a phillips head screwdriver, remove the two screws from the right hand cover and unplug motor power cable. Remove right hand cover from the opener to expose electronics and wiring.

b. Remove potentiometer gear. Unsnap the circuit board from the chassis stand-offs and lower the circuit board as shown.

NOTE: Do not disconnect the two ground wires (A & B) from the circuit board or the chassis.

c. Using pliers, compress 3 snaps of the strain relief fitting inside the chassis and push fitting out of the chassis. Cut opener power cord to a length that will leave 6” inside of the junction box.

d. Route opener power cable through the conduit. Strip 2 to 3 inches of outer jacket off power cable, insuring individual wire insulation is not nicked or cut. Strip approximately 3/4” of insulation off each individual wire. Using wire nuts, splice each conduit wire with the corresponding wire inside the opener as follows: opener black (line), opener white (neutral), and opener yellow and green (ground).

NOTE: Select 1/2” conduit fitting/ J-box that will not interfere with the opener disconnect cable fittings when disconnect is pulled.

e. Reinstall the circuit board back into the opener chassis and snap the board back into the chassis stand-offs.

NOTE: Make sure antenna wire is routed through the chassis grommet and angled 45 degrees to right when board is installed.

f.Confirm pot nut position* shown below.

g.Reinstall the potentiometer gear, right hand cover, and screws.

h.Reconnect Power

OPERATION

Potentiometer Gear

 

Junction

Antenna

Box

 

Grommet

Chassis

StandoffStrain

Relief Fitting

Green and Yellow

Chassis

(Ground)

“A”

“B”

*Potentiometer

Gear Clip

1/8” – 3/16” *Position Pot Nut

Gap 1/8” - 3/16” Away from Left Stop

Standoff

Black (Line)

White

(Neutral)

No Interference

Between Conduit

And Disconnect

View Of Right Hand Side

Please Do Not Return This Product To The Store. Call Us Directly! Our Trained Technicians Will Answer Your Questions and/or Ship Any Parts You May Need. 39 You can reach us Toll Free at 1-888-827-3667 for Consumer Assistance or online at www.wayne-dalton.com

Page 44 Page 46
Image 45
Page 44 Page 46
Contents Your Copyright 2008 Wayne-Dalton Corp. Part No Rev 2 7/16/2008Network ForPackage Contents Look for this symbol When Installing a NEW Door with AN IdrivePre-Installation InspectionEyes to Prevent Possible Severe or Fatal Injury Tools Needed System RequirementsWAYNE-DALTON Track Radius Photoelectric LOW Head Door Models below require the use of photo eyesDefinition of key words used in this manual Table of ContentsDrum Wrap & End Bracket Retro-Fit InstallationRemoval Spring Tension RemovalEnd Bracket Removal Center Bracket & Cable DrumBracket and Gear Powerful Spring Releasing ITS Retro-Fit InstallationEven Fatal Injury IMPORTANT! Right and Left Hand isRemoval End Bracket RemovalVertical Track Height Adjustment Re-Install If NecessaryTop Bracket 8000/8100/8200 TrackTop Roller Adjustment Failure to RE-ATTACH HorizontalTracks to the Support Before Opening Door can Cause Door Assembling Opener InstallationCable Drums Secure end bracket to the flag angle using Tools Needed Power Drill Socket Driver Wrench Step LadderEnd Brackets Repeat for other end bracketCable Drum/ Drive Gear InstallationEnd Bracket Installation BracketsCounterbalance Springs Positioning Support Bracket Attaching Opener ToSupport Bracket Pliers Attaching Disconnect CableBracket Slack between opener and right endMounting Disconnect Pilot drill lag screw location using 1/8 drill bitHandle Bracket 6ftDisconnect Handle Usage Attaching Disconnect HandleSprings Cable AdjustmentsSecuring Door For Spring WindingTools Needed Vice Clamps Hands Winding SpringsRecommended Spring Turns Drum Wrap InstallationTools Needed IMPORTANT! do not Overwind SpringsProblems Setting Spring TensionIMPORTANT! do not Overwind SCREWS. for Detailed Information onMounting Wall Station Drum Wrap InstallationInstalling Battery Disconnect Power to Installing the Light FixtureInstall hole plug into the screw hole in the light fixture If IncludedPower Cord Connecting OpenerAttaching Diffuser If IncludedSensor Unit For Proper AlignmentView of the Opener from the Front Sensor Wire InstallationChecking for Obstructions Safety Sensor AlignmentProgramming Light Fixture On when program button is pushedProfile Routine Standard Upper Limit On and remain on for 30 secondsAdjusting Detent Profile Routine Custom Upper LimitWork Properly Confirm adjustment Lock Arm InstallationTurn increments Tools Needed Tape Measure Step LadderContact Obstruction Test Lock Arm InstallationFatal Injury MAY Result Testing the Safety SensorsDoor activation Read and Follow ALL InstructionsEmergency Disconnect Never GO Under a STOPPED, Partially Open DoorOperating the Wireless Wall Station Teaching HomeLink to the idrive opener Programming/Training HomeLink UnitProgramming/Training HomeLink Unit Custom pet position Customizing the SettingsMulti-Door Programming For more profile options go to page 28Maintenance Reconnect Power Power Connection Permanent Wiring OptionConfirm pot nut position* shown below Potentiometer GearHandle In Manual Door Operated Position Motor Up Position Stations or Transmitters to OpenerProgramming Wireless WallRed Program Button Light Button Large ButtonSymptom Probable Cause Corrective Action TroubleshootingLock Arm Troubleshooting Dalton dealer or distributor Pre-drill 3/32 pilot hole Cut-Out Template to Aid InstallationPre-drill 5/64 pilot hole Thank you for your purchaseModels 3790/3790-Z Patent Information
Top Page Image Contents