Wayne-Dalton 3790 Pre-Installation, Inspection, Eyes to Prevent Possible Severe or Fatal Injury

Page 4

PRE-INSTALLATION INSPECTION

CAUTION! Do not install this opener on your door unless the following requirements are met.

Electrical outlet on

Electrical outlet on the

A

the ceiling is for

wall is for opener

 

light/opener

 

 

Mounting Surface

C

 

 

Torquemaster® Plus

Torquemaster®

 

 

Controls

B 1” Clearance for Motor

Torque Tube

 

 

Learn

S1 S2 S3 S4 Delete

 

 

Z-Wave enabled

 

End Bracket

 

what’s

 

OPENING

your world?

With Z-Wave®technology you can control your lights, thermostat and start your morning coffee,

all withthe single touch of a button.

Find out more:

www.Wayne-Dalton.com/access

P/N 335982

Top of

Door

 

 

 

 

 

 

 

Pre-Installation

 

 

WARNING

PHOTOELECTRIC EYES ARE NOT REQUIRED ON WAYNE-DALTON

 

 

 

SERIES 9000 AND MODEL 5120 AND 5140 DOORS. ALL OTHER

 

Inspection

 

DOORS, WHICH DO NOT

HAVE PINCH-RESISTANT SECTION JOINTS, REQUIRE PHOTOELECTRIC

 

 

EYES TO PREVENT POSSIBLE SEVERE OR FATAL INJURY.

CAUTION: DO NOT INSTALL THIS OPENER ON YOUR DOOR UNLESS THE FOLLOWING REQUIREMENTS ARE MET. USE THE ILLUSTRATION ABOVE AS A VISUAL AID.

A. You must have a Wayne-Dalton Torquemaster® or Torquemaster®

D. Your door must not exceed 8' in height.

Plus counterbalance system to install this opener (see A above).

E. The idrive® opener will only work on sectional doors. Do not

B. The motor requires 1" of clearance above the top of the end

install on one-piece doors.

bracket for Torquemaster and 1-1/4” of clearance above the top

F. Your garage door must be properly balanced (door must not be

of the end bracket for Torquemaster plus.

heavy to lift, nor lift by itself).

 

C. Two electrical outlets are recommended for the idrive®

G. Horizontal tracks should be raised 1" above level at rear of Track.

installation. One of these outlets needs to be located less than 6'

 

from the opener. The second outlet, for the light, can be located

H. We do not recommend installing the idrive® opener on

at a position of your choice.

Model 9700 door widths of 16’ - 18’.

If, in the event that an electrical outlet is not located within 6' of

I. Maximum door weight (without spring tension) must not

the opener, contact a local electrician for further options. As a

exceed 304 lb.

convenience, an electrical outlet is provided on the light fixture.

 

The 6’ opener cord can be used with this outlet.

 

IIIPlease Do Not Return This Product To The Store. Call Us Directly! Our Trained Technicians Will Answer Your Questions and/or Ship Any Parts You May Need.

You can reach us Toll Free at 1-888-827-3667 for Consumer Assistance or online at www.wayne-dalton.com

Image 4
Contents Copyright 2008 Wayne-Dalton Corp. Part No Rev 2 7/16/2008 YourNetwork ForPackage Contents When Installing a NEW Door with AN Idrive Look for this symbolInspection Pre-InstallationEyes to Prevent Possible Severe or Fatal Injury System Requirements Tools NeededWAYNE-DALTON Track Radius Photoelectric LOW Head Door Models below require the use of photo eyesTable of Contents Definition of key words used in this manualRetro-Fit Installation Drum Wrap & End BracketRemoval Spring Tension RemovalCenter Bracket & Cable Drum End Bracket RemovalBracket and Gear Retro-Fit Installation Powerful Spring Releasing ITSEven Fatal Injury IMPORTANT! Right and Left Hand isEnd Bracket Removal RemovalRe-Install If Necessary Vertical Track Height AdjustmentTop Bracket 8000/8100/8200 TrackFailure to RE-ATTACH Horizontal Top Roller AdjustmentTracks to the Support Before Opening Door can Cause Door Installation Assembling OpenerCable Drums Tools Needed Power Drill Socket Driver Wrench Step Ladder Secure end bracket to the flag angle usingEnd Brackets Repeat for other end bracketInstallation Cable Drum/ Drive GearBrackets End Bracket InstallationCounterbalance Springs Attaching Opener To Positioning Support BracketSupport Bracket Attaching Disconnect Cable PliersBracket Slack between opener and right endPilot drill lag screw location using 1/8 drill bit Mounting DisconnectHandle Bracket 6ftAttaching Disconnect Handle Disconnect Handle UsageCable Adjustments SpringsFor Spring Winding Securing DoorTools Needed Vice Clamps Winding Springs HandsDrum Wrap Installation Recommended Spring TurnsTools Needed IMPORTANT! do not Overwind SpringsSetting Spring Tension ProblemsIMPORTANT! do not Overwind SCREWS. for Detailed Information onDrum Wrap Installation Mounting Wall StationInstalling Battery Installing the Light Fixture Disconnect Power toInstall hole plug into the screw hole in the light fixture If IncludedConnecting Opener Power CordAttaching Diffuser If IncludedFor Proper Alignment Sensor UnitSensor Wire Installation View of the Opener from the FrontSafety Sensor Alignment Checking for ObstructionsOn when program button is pushed Programming Light FixtureProfile Routine Standard Upper Limit On and remain on for 30 secondsProfile Routine Custom Upper Limit Adjusting DetentWork Properly Lock Arm Installation Confirm adjustmentTurn increments Tools Needed Tape Measure Step LadderLock Arm Installation Contact Obstruction TestTesting the Safety Sensors Fatal Injury MAY ResultRead and Follow ALL Instructions Door activationEmergency Disconnect Never GO Under a STOPPED, Partially Open DoorOperating the Wireless Wall Station Programming/Training HomeLink Unit Teaching HomeLink to the idrive openerProgramming/Training HomeLink Unit Customizing the Settings Custom pet positionMulti-Door Programming For more profile options go to page 28Maintenance Power Connection Permanent Wiring Option Reconnect PowerConfirm pot nut position* shown below Potentiometer GearStations or Transmitters to OpenerProgramming Wireless Wall Handle In Manual Door Operated Position Motor Up PositionRed Program Button Light Button Large ButtonTroubleshooting Symptom Probable Cause Corrective ActionLock Arm Troubleshooting Dalton dealer or distributor Cut-Out Template to Aid Installation Pre-drill 3/32 pilot holePre-drill 5/64 pilot hole Thank you for your purchasePatent Information Models 3790/3790-Z