Wayne-Dalton 3790-Z installation instructions Attaching Disconnect Handle, Disconnect Handle Usage

Page 21

8Attaching Disconnect Handle

Tools Needed:

NOTE: The motor must be in the fully down

position before setting handle position on

 

Phillips

cable. Bring motor to the down position by

Head

pulling the disconnect cable while pushing

the motor down. Insure opener disconnect

Screwdriver

teeth are engaged before installing

Wire Cutters

disconnect handle. If motor is not fully down

when teeth are engaged, turn motor shaft

 

Flat Blade

with screwdriver at back of motor counter

clockwise until motor is fully down.

Screwdriver

NOTE: Do not use power drill to assemble set

 

 

screw to handle.

 

Start the #6-20 x 1/2" screw into the

 

disconnect handle. Thread the disconnect

 

cable through the top of the disconnect

 

handle bracket and then the disconnect

 

handle.

 

Locate the disconnect handle in full upper

 

position of disconnect handle bracket.

 

Remove all disconnect cable slack between

 

the opener and the top of the disconnect

 

handle bracket. Tighten #6-20 x 1/2" screw

 

into the disconnect handle until snug, and

 

then tighten screw an additional 1 to 1-1/2

 

turns to secure disconnect cable to the

 

disconnect handle. Trim off excess cable

 

from bottom of the disconnect handle.

 

CAUTION: PULL CABLE ONLY TAUT ENOUGH

 

TO REMOVE THE CABLE SLACK. PULLING

 

THE CABLE MORE COULD CAUSE OPENER

 

TO DISCONNECT FROM THE TORQUE TUBE

 

AND CAUSE FAILURE OF THE DISCONNECT.

Upper

Position

#6-20 x 1/2”

Screw

Disconnect

Handle

Disconnect

Cable Disconnect

Handle

Bracket

®INSTALLATION TORQUEMASTER

9

Tools Needed:

None

Disconnect Handle Usage

Apply emergency disconnect label next to the mounted bracket. Use mechanical fasteners if adhesive will not adhere.

Using the emergency disconnect, pull down on disconnect handle and place it in the manual door operated position (use disconnect label for reference). Motor will be rotated 90° from its packaged position.

If motor does not pivot 90°, see troubleshooting section in this manual.

Manual operated position

Motor operated position

Emergency

Disconnect

Label

®FOR IDRIVE

Please Do Not Return This Product To The Store. Call Us Directly! Our Trained Technicians Will Answer Your Questions and/or Ship Any Parts You May Need. 15 You can reach us Toll Free at 1-888-827-3667 for Consumer Assistance or online at www.wayne-dalton.com

Page 20 Page 22
Image 21
Page 20 Page 22
Contents Your Copyright 2008 Wayne-Dalton Corp. Part No Rev 2 7/16/2008Network ForPackage Contents Look for this symbol When Installing a NEW Door with AN IdrivePre-Installation InspectionEyes to Prevent Possible Severe or Fatal Injury Tools Needed System RequirementsWAYNE-DALTON Track Radius Photoelectric LOW Head Door Models below require the use of photo eyesDefinition of key words used in this manual Table of ContentsDrum Wrap & End Bracket Retro-Fit InstallationRemoval Spring Tension RemovalEnd Bracket Removal Center Bracket & Cable DrumBracket and Gear Powerful Spring Releasing ITS Retro-Fit InstallationEven Fatal Injury IMPORTANT! Right and Left Hand isRemoval End Bracket RemovalVertical Track Height Adjustment Re-Install If NecessaryTop Bracket 8000/8100/8200 TrackTop Roller Adjustment Failure to RE-ATTACH HorizontalTracks to the Support Before Opening Door can Cause Door Assembling Opener InstallationCable Drums Secure end bracket to the flag angle using Tools Needed Power Drill Socket Driver Wrench Step LadderEnd Brackets Repeat for other end bracketCable Drum/ Drive Gear InstallationEnd Bracket Installation BracketsCounterbalance Springs Positioning Support Bracket Attaching Opener ToSupport Bracket Pliers Attaching Disconnect CableBracket Slack between opener and right endMounting Disconnect Pilot drill lag screw location using 1/8 drill bitHandle Bracket 6ftDisconnect Handle Usage Attaching Disconnect HandleSprings Cable AdjustmentsSecuring Door For Spring WindingTools Needed Vice Clamps Hands Winding SpringsRecommended Spring Turns Drum Wrap InstallationTools Needed IMPORTANT! do not Overwind SpringsProblems Setting Spring TensionIMPORTANT! do not Overwind SCREWS. for Detailed Information onMounting Wall Station Drum Wrap InstallationInstalling Battery Disconnect Power to Installing the Light FixtureInstall hole plug into the screw hole in the light fixture If IncludedPower Cord Connecting OpenerAttaching Diffuser If IncludedSensor Unit For Proper AlignmentView of the Opener from the Front Sensor Wire InstallationChecking for Obstructions Safety Sensor AlignmentProgramming Light Fixture On when program button is pushedProfile Routine Standard Upper Limit On and remain on for 30 secondsAdjusting Detent Profile Routine Custom Upper LimitWork Properly Confirm adjustment Lock Arm InstallationTurn increments Tools Needed Tape Measure Step LadderContact Obstruction Test Lock Arm InstallationFatal Injury MAY Result Testing the Safety SensorsDoor activation Read and Follow ALL InstructionsEmergency Disconnect Never GO Under a STOPPED, Partially Open DoorOperating the Wireless Wall Station Teaching HomeLink to the idrive opener Programming/Training HomeLink UnitProgramming/Training HomeLink Unit Custom pet position Customizing the SettingsMulti-Door Programming For more profile options go to page 28Maintenance Reconnect Power Power Connection Permanent Wiring OptionConfirm pot nut position* shown below Potentiometer GearHandle In Manual Door Operated Position Motor Up Position Stations or Transmitters to OpenerProgramming Wireless WallRed Program Button Light Button Large ButtonSymptom Probable Cause Corrective Action TroubleshootingLock Arm Troubleshooting Dalton dealer or distributor Pre-drill 3/32 pilot hole Cut-Out Template to Aid InstallationPre-drill 5/64 pilot hole Thank you for your purchaseModels 3790/3790-Z Patent Information
Top Page Image Contents