Wayne-Dalton 3790-Z Programming/Training HomeLink Unit, Teaching HomeLink to the idrive opener

Page 41

❉

Programming HomeLink® System to the Torquemaster® idrive® (Primary)

 

NOTE: This step can only be done on automobiles equipped with the HomeLink® system.

NOTE: Programming HomeLink® requires a Wayne-Dalton Transmitter that is programmed to the opener (the wallstation and transmitter(s) supplied with the opener, come pre-programmed from the factory). Any additional wallstation(s) or transmitter(s) will need to be programmed to the opener, see page 40.

IMPORTANT! Use the programming instructions provided with your vehicle first. Follow these instructions if the HomeLink® unit does not learn the transmitter, when using the vehicle’s instructions.

NOTE: If Primary programming does not work then use the Alternate procedure on next page.

NOTE: Vehicle may need to be in accessory position when programming. Check car owner’s manual.

NOTE: HomeLink® is a registered trademark of Johnson Controls.

Programming/Training HomeLink® Unit

WARNING

GARAGE DOOR MAY OPERATE DURING PROGRAMMING. TO AVOID POSSIBLE SEVERE OR FATAL INJURY, PLACE THE EMERGENCY DISCONNECT HANDLE IN THE MANUAL OPERATED POSITION.

1.Pull the manual disconnect to put the opener in the disengaged position.

2.Verify the HomeLink® unit has an empty channel – press the desired HomeLink® button and observe the LED – if it flashes slowly, the channel is empty and ready for programming. If pressing the desired channel/button causes the LED to blink rapidly, or come on without blinking this channel is already programmed. You either need to choose a different channel/ button on the HomeLink®, or perform Step 3 below.

3.OPTIONAL – To completely clear all channels on the HomeLink® unit, press and hold the two outside buttons on the HomeLink® unit until the HomeLink® LED light begins to flash rapidly (approx. 20 seconds), then release both buttons. (Do not perform this step to train additional hand-held transmitters.) NOTE: This operation erases all previously learned transmitters and you will need to re-teach any other transmitters to your HomeLink® unit.

4.Hold the end of the Wayne Dalton hand-held transmitter approximately 1 to 3 inches away from the HomeLink® surface – keeping the HomeLink® indicator light in view.

5.Simultaneously press and hold the Wayne Dalton transmitter large button and desired button on the HomeLink® module, continue to hold both buttons. In less than 10 seconds the LED on the HomeLink® module will either go solid or give a single quick flash, release both buttons when either occur.

NOTE: If this procedure is unsuccessful, perform Alternate procedure on next page.

Teaching HomeLink® to the idrive® opener

6.Press and release the red program button on the idrive® opener. The idrive® unit will beep once, indicating that it is ready to learn.

NOTE: The idrive® will remain in the learn mode for 30 seconds.

7.Press the HomeLink® button used in Step 5 above for 1 to 3 seconds. The idrive® will beep indicating a successful learn.

8.Return the manual disconnect to the engaged position.

9.Press the HomeLink® button once more to operate the door.

NOTE: The first transmitter command after programming will only move the door through a six inch up/down cycle. Normal door operations will occur on the second use of the transmitter.

OPERATION

Please Do Not Return This Product To The Store. Call Us Directly! Our Trained Technicians Will Answer Your Questions and/or Ship Any Parts You May Need. 35 You can reach us Toll Free at 1-888-827-3667 for Consumer Assistance or online at www.wayne-dalton.com

Page 40 Page 42
Image 41
Page 40 Page 42
Contents Your Copyright 2008 Wayne-Dalton Corp. Part No Rev 2 7/16/2008Network ForPackage Contents Look for this symbol When Installing a NEW Door with AN IdriveEyes to Prevent Possible Severe or Fatal Injury Pre-InstallationInspection Tools Needed System RequirementsWAYNE-DALTON Track Radius Photoelectric LOW Head Door Models below require the use of photo eyesDefinition of key words used in this manual Table of ContentsDrum Wrap & End Bracket Retro-Fit InstallationRemoval Spring Tension RemovalBracket and Gear End Bracket RemovalCenter Bracket & Cable Drum Powerful Spring Releasing ITS Retro-Fit InstallationEven Fatal Injury IMPORTANT! Right and Left Hand isRemoval End Bracket RemovalVertical Track Height Adjustment Re-Install If NecessaryTop Bracket 8000/8100/8200 TrackTracks to the Support Before Opening Door can Cause Door Top Roller AdjustmentFailure to RE-ATTACH Horizontal Assembling Opener InstallationCable Drums Secure end bracket to the flag angle using Tools Needed Power Drill Socket Driver Wrench Step LadderEnd Brackets Repeat for other end bracketCable Drum/ Drive Gear InstallationCounterbalance Springs End Bracket InstallationBrackets Support Bracket Positioning Support BracketAttaching Opener To Pliers Attaching Disconnect CableBracket Slack between opener and right endMounting Disconnect Pilot drill lag screw location using 1/8 drill bitHandle Bracket 6ftDisconnect Handle Usage Attaching Disconnect HandleSprings Cable AdjustmentsTools Needed Vice Clamps Securing DoorFor Spring Winding Hands Winding SpringsRecommended Spring Turns Drum Wrap InstallationTools Needed IMPORTANT! do not Overwind SpringsProblems Setting Spring TensionIMPORTANT! do not Overwind SCREWS. for Detailed Information onMounting Wall Station Drum Wrap InstallationInstalling Battery Disconnect Power to Installing the Light FixtureInstall hole plug into the screw hole in the light fixture If IncludedPower Cord Connecting OpenerAttaching Diffuser If IncludedSensor Unit For Proper AlignmentView of the Opener from the Front Sensor Wire InstallationChecking for Obstructions Safety Sensor AlignmentProgramming Light Fixture On when program button is pushedProfile Routine Standard Upper Limit On and remain on for 30 secondsWork Properly Adjusting DetentProfile Routine Custom Upper Limit Confirm adjustment Lock Arm InstallationTurn increments Tools Needed Tape Measure Step LadderContact Obstruction Test Lock Arm InstallationFatal Injury MAY Result Testing the Safety SensorsDoor activation Read and Follow ALL InstructionsEmergency Disconnect Never GO Under a STOPPED, Partially Open DoorOperating the Wireless Wall Station Teaching HomeLink to the idrive opener Programming/Training HomeLink UnitProgramming/Training HomeLink Unit Custom pet position Customizing the SettingsMulti-Door Programming For more profile options go to page 28Maintenance Reconnect Power Power Connection Permanent Wiring OptionConfirm pot nut position* shown below Potentiometer GearHandle In Manual Door Operated Position Motor Up Position Stations or Transmitters to OpenerProgramming Wireless WallRed Program Button Light Button Large ButtonSymptom Probable Cause Corrective Action TroubleshootingLock Arm Troubleshooting Dalton dealer or distributor Pre-drill 3/32 pilot hole Cut-Out Template to Aid InstallationPre-drill 5/64 pilot hole Thank you for your purchaseModels 3790/3790-Z Patent Information
Top Page Image Contents