Wayne-Dalton 3790-Z Profile Routine Custom Upper Limit, Adjusting Detent, Work Properly

Page 35

25

Tools Needed:

None

Profile Routine

(Custom Upper Limit)

WARNING

TO AVOID INJURY, NO ONE SHOULD CROSS THE PATH OF A MOVING DOOR!

NOTE: If no obstruction interferes with a standard upper limit, skip this step.

NOTE: The door must be in its fully closed position and the disconnect handle must be in the motor operated position (upper position) to initiate the profile routine.

NOTE: Install profile will not run if safety sensors are not aligned (Only if required for your door).

Press and hold the profile button for five (5) seconds. The opener will beep twice, release the profile button, indicating the activation of the profile routine.

When the door moves to the desired upper limit, press and hold the Up/Down button on the wall station until the door stops. Next, the door will close completely. The Up/Down button (when door is closed) can be activated by pressing center of flip cover.

Next, the door will go through one more Up/ Down cycle. Once this is complete, the door limits are set and the profile is complete.

Alternately, once an profile routine has been successfully completed, disconnect door and manually move to desired upper limit. Re-connect door and press and hold the profile button for five (5) seconds. The door will close, open and close to complete the profile routine with the new custom upper limit.

NOTE: For a more precise location of the custom upper limit, see “Customizing the Settings” on page 37.

Up/Down

Button

Profile Button

26

Adjusting Detent

 

 

 

Tools Needed:

The amount of pressure the opener

uses to pivot the motor downward is

 

Flat Tip

preset at the factory via the detent pin

Screwdriver

adjustment screw.

 

Step Ladder

Due to variations in door installations,

a detent pin adjustment may need to

 

 

be made in order to insure proper pivoting

 

of the motor.

 

IMPORTANT! FOR SYSTEM SECURITY:

 

THE MOTOR IS DESIGNED TO PIVOT DOWN

 

AFTER THE DOOR CLOSES COMPLETELY. IF

 

THE MOTOR DOES NOT PIVOT OR PIVOTS

 

TOO SOON, THE DETENT PIN ADJUSTMENT

 

SCREW MAY NEED TO BE ADJUSTED IN

 

ORDER FOR THE DOOR LOCK FEATURE TO

 

WORK PROPERLY.

 

 

Detent Pin

Adjustment Screw

Z-

Wave

®

enabled

 

 

 

 

 

 

 

what’s

 

OPENING

 

your world?

 

With Z-

®

 

 

 

technology

Wave

 

 

you can

 

control

 

 

 

 

 

 

your l

 

 

thermostat

ights,

 

 

your

andstart

 

 

mor

 

 

 

 

ning coffee,

 

 

all withthe

single

 

 

t

 

 

 

ouch

 

 

 

 

of a b

 

 

 

 

utton.

 

www.

Find out more:

 

 

Wayne-

 

 

 

 

Dalton.co

 

 

 

 

m/access

 

 

 

P/N 335982

 

 

 

PRE-OPERATION

Please Do Not Return This Product To The Store. Call Us Directly! Our Trained Technicians Will Answer Your Questions and/or Ship Any Parts You May Need. 29 You can reach us Toll Free at 1-888-827-3667 for Consumer Assistance or online at www.wayne-dalton.com

Page 34 Page 36
Image 35
Page 34 Page 36
Contents For Copyright 2008 Wayne-Dalton Corp. Part No Rev 2 7/16/2008Your NetworkPackage Contents Look for this symbol When Installing a NEW Door with AN IdriveEyes to Prevent Possible Severe or Fatal Injury Pre-InstallationInspection Door Models below require the use of photo eyes System RequirementsTools Needed WAYNE-DALTON Track Radius Photoelectric LOW HeadDefinition of key words used in this manual Table of ContentsSpring Tension Removal Retro-Fit InstallationDrum Wrap & End Bracket RemovalBracket and Gear End Bracket RemovalCenter Bracket & Cable Drum IMPORTANT! Right and Left Hand is Retro-Fit InstallationPowerful Spring Releasing ITS Even Fatal InjuryRemoval End Bracket Removal8000/8100/8200 Track Re-Install If NecessaryVertical Track Height Adjustment Top BracketTracks to the Support Before Opening Door can Cause Door Top Roller AdjustmentFailure to RE-ATTACH Horizontal Assembling Opener InstallationCable Drums Repeat for other end bracket Tools Needed Power Drill Socket Driver Wrench Step LadderSecure end bracket to the flag angle using End BracketsCable Drum/ Drive Gear InstallationCounterbalance Springs End Bracket InstallationBrackets Support Bracket Positioning Support BracketAttaching Opener To Slack between opener and right end Attaching Disconnect CablePliers Bracket6ft Pilot drill lag screw location using 1/8 drill bitMounting Disconnect Handle BracketDisconnect Handle Usage Attaching Disconnect HandleSprings Cable AdjustmentsTools Needed Vice Clamps Securing DoorFor Spring Winding Hands Winding SpringsIMPORTANT! do not Overwind Springs Drum Wrap InstallationRecommended Spring Turns Tools NeededSCREWS. for Detailed Information on Setting Spring TensionProblems IMPORTANT! do not OverwindMounting Wall Station Drum Wrap InstallationInstalling Battery If Included Installing the Light FixtureDisconnect Power to Install hole plug into the screw hole in the light fixtureIf Included Connecting OpenerPower Cord Attaching DiffuserSensor Unit For Proper AlignmentView of the Opener from the Front Sensor Wire InstallationChecking for Obstructions Safety Sensor AlignmentOn and remain on for 30 seconds On when program button is pushedProgramming Light Fixture Profile Routine Standard Upper LimitWork Properly Adjusting DetentProfile Routine Custom Upper Limit Tools Needed Tape Measure Step Ladder Lock Arm InstallationConfirm adjustment Turn incrementsContact Obstruction Test Lock Arm InstallationFatal Injury MAY Result Testing the Safety SensorsNever GO Under a STOPPED, Partially Open Door Read and Follow ALL InstructionsDoor activation Emergency DisconnectOperating the Wireless Wall Station Teaching HomeLink to the idrive opener Programming/Training HomeLink UnitProgramming/Training HomeLink Unit For more profile options go to page 28 Customizing the SettingsCustom pet position Multi-Door ProgrammingMaintenance Potentiometer Gear Power Connection Permanent Wiring OptionReconnect Power Confirm pot nut position* shown belowLight Button Large Button Stations or Transmitters to OpenerProgramming Wireless WallHandle In Manual Door Operated Position Motor Up Position Red Program ButtonSymptom Probable Cause Corrective Action TroubleshootingLock Arm Troubleshooting Dalton dealer or distributor Thank you for your purchase Cut-Out Template to Aid InstallationPre-drill 3/32 pilot hole Pre-drill 5/64 pilot holeModels 3790/3790-Z Patent Information
Top Page Image Contents