Wayne-Dalton 3790-Z installation instructions Attaching Disconnect Cable, Pliers, Bracket

Page 19

6Attaching Disconnect Cable

	Tools Needed:	Attach the loose disconnect cable (located in
	Step Ladder	opener hardware bag) to the opener with the
	Step Ladder	“S” hook. Close both ends of the “S” hook
	Pliers	“S” hook. Close both ends of the “S” hook
	Pliers	with pliers, to lock assembly together with
		pliers.
		Thread the disconnect cable (behind the
		counterbalance cable) through the hole in
		the right hand end bracket, and remove all
		slack between opener and right end
		bracket.

Close “S” Hook

Torquemaster®	Right Side of
	End Bracket
	End Bracket

		Hole in
		End Bracket

S-Hook

Disconnect

Cable

Hole in Right

End Bracket

®INSTALLATION TORQUEMASTER

Torquemaster® Plus

Hole in

End Bracket

Right Side of End

S-HookBracket

Disconnect

Cable

Hole in Right

End Bracket

®FOR IDRIVE

Please Do Not Return This Product To The Store. Call Us Directly! Our Trained Technicians Will Answer Your Questions and/or Ship Any Parts You May Need. 13 You can reach us Toll Free at 1-888-827-3667 for Consumer Assistance or online at www.wayne-dalton.com

Image 19

Contents For Copyright 2008 Wayne-Dalton Corp. Part No Rev 2 7/16/2008Your NetworkPackage Contents Look for this symbol When Installing a NEW Door with AN IdriveInspection Pre-InstallationEyes to Prevent Possible Severe or Fatal Injury Door Models below require the use of photo eyes System RequirementsTools Needed WAYNE-DALTON Track Radius Photoelectric LOW HeadDeﬁnition of key words used in this manual Table of ContentsSpring Tension Removal Retro-Fit InstallationDrum Wrap & End Bracket RemovalCenter Bracket & Cable Drum End Bracket RemovalBracket and Gear IMPORTANT! Right and Left Hand is Retro-Fit InstallationPowerful Spring Releasing ITS Even Fatal InjuryRemoval End Bracket Removal8000/8100/8200 Track Re-Install If NecessaryVertical Track Height Adjustment Top BracketFailure to RE-ATTACH Horizontal Top Roller AdjustmentTracks to the Support Before Opening Door can Cause Door Assembling Opener InstallationCable Drums Repeat for other end bracket Tools Needed Power Drill Socket Driver Wrench Step LadderSecure end bracket to the flag angle using End BracketsCable Drum/ Drive Gear InstallationBrackets End Bracket InstallationCounterbalance Springs Attaching Opener To Positioning Support BracketSupport Bracket Slack between opener and right end Attaching Disconnect CablePliers Bracket6ft Pilot drill lag screw location using 1/8 drill bitMounting Disconnect Handle BracketDisconnect Handle Usage Attaching Disconnect HandleSprings Cable AdjustmentsFor Spring Winding Securing DoorTools Needed Vice Clamps Hands Winding SpringsIMPORTANT! do not Overwind Springs Drum Wrap InstallationRecommended Spring Turns Tools NeededSCREWS. for Detailed Information on Setting Spring TensionProblems IMPORTANT! do not OverwindMounting Wall Station Drum Wrap InstallationInstalling Battery If Included Installing the Light FixtureDisconnect Power to Install hole plug into the screw hole in the light fixtureIf Included Connecting OpenerPower Cord Attaching DiffuserSensor Unit For Proper AlignmentView of the Opener from the Front Sensor Wire InstallationChecking for Obstructions Safety Sensor AlignmentOn and remain on for 30 seconds On when program button is pushedProgramming Light Fixture Profile Routine Standard Upper LimitProfile Routine Custom Upper Limit Adjusting DetentWork Properly Tools Needed Tape Measure Step Ladder Lock Arm InstallationConfirm adjustment Turn incrementsContact Obstruction Test Lock Arm InstallationFatal Injury MAY Result Testing the Safety SensorsNever GO Under a STOPPED, Partially Open Door Read and Follow ALL InstructionsDoor activation Emergency DisconnectOperating the Wireless Wall Station Teaching HomeLink to the idrive opener Programming/Training HomeLink UnitProgramming/Training HomeLink Unit For more profile options go to page 28 Customizing the SettingsCustom pet position Multi-Door ProgrammingMaintenance Potentiometer Gear Power Connection Permanent Wiring OptionReconnect Power Confirm pot nut position* shown belowLight Button Large Button Stations or Transmitters to OpenerProgramming Wireless WallHandle In Manual Door Operated Position Motor Up Position Red Program ButtonSymptom Probable Cause Corrective Action TroubleshootingLock Arm Troubleshooting Dalton dealer or distributor Thank you for your purchase Cut-Out Template to Aid InstallationPre-drill 3/32 pilot hole Pre-drill 5/64 pilot holeModels 3790/3790-Z Patent Information

6Attaching Disconnect Cable

pliers.

slack between opener and right end

bracket.

Torquemaster®

End Bracket