Wayne-Dalton 3790-Z installation instructions System Requirements, Tools Needed

Page 5

System Requirements

CAUTION TO REDUCE THE RISK OF INJURY, USE THIS OPENER ONLY WITH THE FOLLOWING DOOR MODELS:

	WAYNE-DALTON	WAYNE-DALTON	TRACK (RADIUS)	PHOTOELECTRIC	LOW HEAD
	DOOR MODEL	SPRING SYSTEM		SAFETY SENSORS	ROOM KIT


	9000 SERIES,	Torquemaster®	10",12",14",15"	Not Required	Not Required
	5120 & 5140	Torquemaster® Plus

	9000 SERIES,	Torquemaster®	6" Low Head Room	Not Required	P/N 302883
	5120 & 5140	Torquemaster® Plus			Required

Door Models below require the use of photo eyes.

	8000 SERIES or			Torquemaster®	10",12",14",15"	P/N’s 252118 or	Not Required
	other doors			Torquemaster® Plus	10",12",14",15"	301674 Required	Not Required
	other doors			Torquemaster® Plus		301674 Required
	8000 SERIES or			Torquemaster®	6" Low Head Room	P/N’s 252118 or	P/N 302883
	other doors			Torquemaster® Plus	6" Low Head Room	301674 Required	Required
	other doors			Torquemaster® Plus		301674 Required	Required
			Tools Needed

Power Drill	Ratchet Wrench	Pliers/Wire	3/32” Drill Bit	3/16” Drill Bit
		Cutters

Phillips Head	7/16” Socket	Pencil	7/16” Wrench	1/8” Drill Bit	5/64” Drill Bit
Screwdriver

Flat Tip	7/16” Socket Driver	Level	Needle Nose Pliers
Screwdriver

Tape Measure

Safety Glasses

Locking Pliers

Vice Clamps

Step Ladder

Please Do Not Return This Product To The Store. Call Us Directly! Our Trained Technicians Will Answer Your Questions and/or Ship Any Parts You May Need. IV You can reach us Toll Free at 1-888-827-3667 for Consumer Assistance or online at www.wayne-dalton.com

Image 5

Contents Your Copyright 2008 Wayne-Dalton Corp. Part No Rev 2 7/16/2008Network ForPackage Contents Look for this symbol When Installing a NEW Door with AN IdriveEyes to Prevent Possible Severe or Fatal Injury Pre-InstallationInspection Tools Needed System RequirementsWAYNE-DALTON Track Radius Photoelectric LOW Head Door Models below require the use of photo eyesDeﬁnition of key words used in this manual Table of ContentsDrum Wrap & End Bracket Retro-Fit InstallationRemoval Spring Tension RemovalBracket and Gear End Bracket RemovalCenter Bracket & Cable Drum Powerful Spring Releasing ITS Retro-Fit InstallationEven Fatal Injury IMPORTANT! Right and Left Hand isRemoval End Bracket RemovalVertical Track Height Adjustment Re-Install If NecessaryTop Bracket 8000/8100/8200 TrackTracks to the Support Before Opening Door can Cause Door Top Roller AdjustmentFailure to RE-ATTACH Horizontal Assembling Opener InstallationCable Drums Secure end bracket to the flag angle using Tools Needed Power Drill Socket Driver Wrench Step LadderEnd Brackets Repeat for other end bracketCable Drum/ Drive Gear InstallationCounterbalance Springs End Bracket InstallationBrackets Support Bracket Positioning Support BracketAttaching Opener To Pliers Attaching Disconnect CableBracket Slack between opener and right endMounting Disconnect Pilot drill lag screw location using 1/8 drill bitHandle Bracket 6ftDisconnect Handle Usage Attaching Disconnect HandleSprings Cable AdjustmentsTools Needed Vice Clamps Securing DoorFor Spring Winding Hands Winding SpringsRecommended Spring Turns Drum Wrap InstallationTools Needed IMPORTANT! do not Overwind SpringsProblems Setting Spring TensionIMPORTANT! do not Overwind SCREWS. for Detailed Information onMounting Wall Station Drum Wrap InstallationInstalling Battery Disconnect Power to Installing the Light FixtureInstall hole plug into the screw hole in the light fixture If IncludedPower Cord Connecting OpenerAttaching Diffuser If IncludedSensor Unit For Proper AlignmentView of the Opener from the Front Sensor Wire InstallationChecking for Obstructions Safety Sensor AlignmentProgramming Light Fixture On when program button is pushedProfile Routine Standard Upper Limit On and remain on for 30 secondsWork Properly Adjusting DetentProfile Routine Custom Upper Limit Confirm adjustment Lock Arm InstallationTurn increments Tools Needed Tape Measure Step LadderContact Obstruction Test Lock Arm InstallationFatal Injury MAY Result Testing the Safety SensorsDoor activation Read and Follow ALL InstructionsEmergency Disconnect Never GO Under a STOPPED, Partially Open DoorOperating the Wireless Wall Station Teaching HomeLink to the idrive opener Programming/Training HomeLink UnitProgramming/Training HomeLink Unit Custom pet position Customizing the SettingsMulti-Door Programming For more profile options go to page 28Maintenance Reconnect Power Power Connection Permanent Wiring OptionConfirm pot nut position* shown below Potentiometer GearHandle In Manual Door Operated Position Motor Up Position Stations or Transmitters to OpenerProgramming Wireless WallRed Program Button Light Button Large ButtonSymptom Probable Cause Corrective Action TroubleshootingLock Arm Troubleshooting Dalton dealer or distributor Pre-drill 3/32 pilot hole Cut-Out Template to Aid InstallationPre-drill 5/64 pilot hole Thank you for your purchaseModels 3790/3790-Z Patent Information