Wayne-Dalton 3790-Z Customizing the Settings, Custom pet position, Multi-Door Programming

Page 43

❉

Customizing the Settings

 

Custom pet position:

Normal install routine sets the pet position to approximately 8 inches above the ground. The pet opening height may be changed to open anywhere between 8” and 30” above the ground. To change the automatic pet opening height refer to the following procedure:

a. After completion of the normal install routine, with the door in the closed position, place the disconnect handle in the manual operated position.

Manually position the door to the desired pet opening height (between 8” and 30” above ground) and return disconnect handle to the motor operated position.

b. Move the slide switch from the NORMAL (Unlock) position to the DOOR LOCK (Lock) position and then back to the NORMAL (Unlock) position. The opener will beep once. The pet button is now programmed to automatically open the door to this custom height.

NOTE: The opener will NOT accept programmed pet lock position if door is below 8” or higher than 30”.

NOTE: Activation of the normal install routine will reset the pet position to the default 8” target height. For use of the pet button see operation section.

Multi-Door Programming:

Momentarily pressing the button programmed in the transmitter programming step activates the door. Other buttons can also be programmed to activate different doors, for multi-door installations. Each button or a combination of two buttons pressed simultaneously can be programmed to activate a different door. Only one button at a time can be programmed to activate a specific opener.

Custom Upper Limits

Disconnect door and manually move it to the desired upper limit. NOTE: The door must be positioned more than halfway open. Reconnect door.

Press and hold the profile button for 5 seconds. The opener will beep twice, indicating the activation of the profile routine. The door will now move to the closed position. Then, the door will open to the new upper limit.

Next, the door will go down to the closed position. Once this is complete, the door limits are set and the installation is complete.

For more profile options go to page 28 and 29.

NOTE: Before performing custom upper limit, first profile must be done from closed position.

NORMAL

 

DOOR LOCK

 

Up/Down Button

 

Pet Button

 

Up/Down Button

Profile Button

 

OPERATION

Please Do Not Return This Product To The Store. Call Us Directly! Our Trained Technicians Will Answer Your Questions and/or Ship Any Parts You May Need. 37 You can reach us Toll Free at 1-888-827-3667 for Consumer Assistance or online at www.wayne-dalton.com

Page 42 Page 44
Image 43
Page 42 Page 44
Contents For Copyright 2008 Wayne-Dalton Corp. Part No Rev 2 7/16/2008Your NetworkPackage Contents Look for this symbol When Installing a NEW Door with AN IdriveInspection Pre-InstallationEyes to Prevent Possible Severe or Fatal Injury Door Models below require the use of photo eyes System RequirementsTools Needed WAYNE-DALTON Track Radius Photoelectric LOW HeadDefinition of key words used in this manual Table of ContentsSpring Tension Removal Retro-Fit InstallationDrum Wrap & End Bracket RemovalCenter Bracket & Cable Drum End Bracket RemovalBracket and Gear IMPORTANT! Right and Left Hand is Retro-Fit InstallationPowerful Spring Releasing ITS Even Fatal InjuryRemoval End Bracket Removal8000/8100/8200 Track Re-Install If NecessaryVertical Track Height Adjustment Top BracketFailure to RE-ATTACH Horizontal Top Roller AdjustmentTracks to the Support Before Opening Door can Cause Door Assembling Opener InstallationCable Drums Repeat for other end bracket Tools Needed Power Drill Socket Driver Wrench Step LadderSecure end bracket to the flag angle using End BracketsCable Drum/ Drive Gear InstallationBrackets End Bracket InstallationCounterbalance Springs Attaching Opener To Positioning Support BracketSupport Bracket Slack between opener and right end Attaching Disconnect CablePliers Bracket6ft Pilot drill lag screw location using 1/8 drill bitMounting Disconnect Handle BracketDisconnect Handle Usage Attaching Disconnect HandleSprings Cable AdjustmentsFor Spring Winding Securing DoorTools Needed Vice Clamps Hands Winding SpringsIMPORTANT! do not Overwind Springs Drum Wrap InstallationRecommended Spring Turns Tools NeededSCREWS. for Detailed Information on Setting Spring TensionProblems IMPORTANT! do not OverwindMounting Wall Station Drum Wrap InstallationInstalling Battery If Included Installing the Light FixtureDisconnect Power to Install hole plug into the screw hole in the light fixtureIf Included Connecting OpenerPower Cord Attaching DiffuserSensor Unit For Proper AlignmentView of the Opener from the Front Sensor Wire InstallationChecking for Obstructions Safety Sensor AlignmentOn and remain on for 30 seconds On when program button is pushedProgramming Light Fixture Profile Routine Standard Upper LimitProfile Routine Custom Upper Limit Adjusting DetentWork Properly Tools Needed Tape Measure Step Ladder Lock Arm InstallationConfirm adjustment Turn incrementsContact Obstruction Test Lock Arm InstallationFatal Injury MAY Result Testing the Safety SensorsNever GO Under a STOPPED, Partially Open Door Read and Follow ALL InstructionsDoor activation Emergency DisconnectOperating the Wireless Wall Station Teaching HomeLink to the idrive opener Programming/Training HomeLink UnitProgramming/Training HomeLink Unit For more profile options go to page 28 Customizing the SettingsCustom pet position Multi-Door ProgrammingMaintenance Potentiometer Gear Power Connection Permanent Wiring OptionReconnect Power Confirm pot nut position* shown belowLight Button Large Button Stations or Transmitters to OpenerProgramming Wireless WallHandle In Manual Door Operated Position Motor Up Position Red Program ButtonSymptom Probable Cause Corrective Action TroubleshootingLock Arm Troubleshooting Dalton dealer or distributor Thank you for your purchase Cut-Out Template to Aid InstallationPre-drill 3/32 pilot hole Pre-drill 5/64 pilot holeModels 3790/3790-Z Patent Information
Top Page Image Contents