GE C11, AF-300 manual

Page 85

	Item		Specifications	Remarks
	Installation	∙ Indoor use only. Do not install a dusty location(Degree of pollution: 2) or
	location	expose to direct sunlight, corrosive gases, flammable gases.
	Ambient	∙ -10 to +50°C (+14 to +122°F )
	temperature
	Ambient	∙ 5 to 95%RH ( No condensation )
Environment	humidity
	Altitude	∙ 3300 Feet (1000 m) or less

	Vibration	∙ 3 mm:	2 to less than 9 Hz
		∙ 9.8m/s2:	9 to less than 20 Hz
		∙ 2m/s2:	20 to less than 55 Hz
		∙ 2m/s2:	20 to less than 55 Hz
		∙ 1m/s2:	55 to less than 200 Hz
	Storage tem-	∙ -25 to +65°C
	perature
	Storage humid-	∙ 5 to 95% RH (No condensation)
	ity
	Higher	∙ Terminal for connecting power-factor correcting DC reactor (DCR) is pro-		P1, P(+) terminal
	harmonics	vided as standard.
	current
Others	suppression
	Charging sup-	∙ Charging suppression resistor is built-in for all drive unit.
	pression resis-
	tor
	Cooling fan	∙ Cooling fan can be automatically stopped when drive is stopped.
	ON/OFF con-
	trol

- 83-

Image 85

Contents AF-300 C11 TM Table of Contents Safety Instructions Page Compliance with low voltage directive in EU Instructions on use Drive may be dropped causing injuryThere is a risk of fire Otherwise fire could occurOtherwise, fire could occur Instructions on wiringOtherwise electric shock or fire could occur Otherwise electric shock could occurOtherwise accident could occur Instructions on operationThere is a risk of accidents Otherwise burns could occurOtherwise electric shock or injury could occur Instruction on maintenance/inspection, and replacementGeneral instructions Preface Horsepower Input PhasesFactory Installed Options GE Product Code AF-300 Drive Family Input Voltage230VAC, Single phase, 50/60Hz Input 230VAC, 3 phase, 50/60Hz InputReceiving Inspections Before Using This ProductAppearance Handling the Product Carrying Storage precautionsStorage and transportation 1 Storage and transportation environment10 cm Installation and ConnectionAF-300C11 1 Operating environmentConnection 1Basic connectionOtherwise electric shock and fire could occur 1 Functions of main circuit and ground terminals Connecting the main circuit and ground terminalsConnection diagram Connecting the control terminalsCutting of barrier -3-2 Connection of DC reactor 4 Surge absorber connection diagram 7 Control terminal block arrangement FWD 2 Functions of control circuit terminalsDX+ Connection examples 200 to 50/60Hz Mccb Fuse Connection to PLC when analog signal is input from PLC Noise Harmonic componentLeakage current OthersInspection and Preparation before Operation OperationOperation Method 1 General operation methodTrial Run 1 Running commandNames and Functions Keypad PanelIs pressed at the same time as Operating Keypad PanelProcedure Display Press Fundamental functions Selecting FunctionFunction Selection List 1 Table of Function Selection List Voltage adjust Carrier freq 75kHz is set when 0 is specified Sound tone30Ry operation mode Excited when tripped Normally excited To 10.0minControl Functions of Frequency Extension Terminal FunctionsX3 terminal function Tions Jump frequencyHigh Performance Functions Motor ParametersSerial communication option Optional FunctionsF01 F00 Data protectionDetails of Each Function Otherwise injuries could occurMotor runs when F02 Operation methodKey is pressed and decelerates-to-stop when GE Start Software Selection During Terminal Operation This function sets the maximum output frequency F03 Maximum output frequencyF05 F04 Base frequencyF06 F07F10 F11 Electronic thermal O/L relay Select F09 Torque boostElectronic thermal O/L relayLevel F12 Electronic thermal O/L relay thermal time constant Set with F12 Operating time? ì? ? ŒcharacteristicsÀ ÁPhase input Single Phase Input F14 Restart mode after momentary power failureF15 Frequency limiter High F16 Frequency limiter LowF18 Bias frequency F17 Gain For frequency setting signalBias positive Bias negative 20mAdcF21 F20 DC injection brake Starting frequencyF22 DC injection brakeBraking time F25 Stop frequency F23 Starting frequencyF24 F26 Motor sound carrier freqF27 Motor sound sound tone F30 FM terminal voltage adjustF31 FM terminal Function Normal Tripped Operation F36 30Ry operation modeX1 terminal function E01 E02 E03X2 terminal function X3 terminal functionFrom previous P00 Motor characteristics C07 Multistep frequency settingC01 C02 C03 Jump frequency 1, 2 C04 Jump frequency HysteresisH02 Trip history H01 Operation timeH20 PID control Mode select H04 Auto ResetData initialization H03H22 PID control P-gain H21 PID control Feedback signalH23 PID control I-gain H25 PID control Feedback filterRS485 RTU communication O00 Option selectionOptional RS485 serial communication unit List of protective functions Protective Function1 List of Protective Functions Keypad panel Normal display Alarm display Display Alarm ResetAlarm output Trip Otherwise fire could occurCase of tripping TroubleshootingLoad excessive? Does OU activate when load is removed Power supply voltage within specified value?Consider using DC OvervoltageOUHeat sink overheat- ing OH1 Drive overload OLU or motor overload OL Is electronic thermal O/L relay setting correct?Noise source nearby? Probable faulty drive. Contact GE Fuji Set o00 toConnect the input wires correctly Input phase failure Lin and imbalanceMotor does not start Setting too low? When motor rotates but the speed does not changeMotor generates ab Function change is disabled Normal heat When motor stalls during accelerationTo 0? Set F00 toDaily Inspection Maintenance and InspectionPeriodic Inspection There is danger of electric shockDiscoloration and distortion Visual Not abnormal 1 Periodic inspection listElectrolyte leakage Visual Not abnormal More Overheating? Is off 2Tighten more 3Visual inspection Single -phase Three-phaseElectrical measurements in the Main Circuit 1 Meter for measuring the main circuitInput series Case of 3-phase input series+ + Motor SupplyInquiries about Products and Product Warranty Warranty Coverage 6Warranty ServiceIN-WARRANTY Failure Checklist Standard Specifications SpecificationsDrive output capacity kVA at RUN Stop Common specificationsPage Page Page Dimensions 00.2 2 68 17.2 D 00.2 Terminal Terminal 1 M2.5 00.2 2 Built-in Options OptionsExternal Options 1 External Options Connection method Applicable DC reactorsCompliance with standards PrecautionsGeneral L1/L L2/N L1/R L2/S L3/T P1 + N- U THR CMGeneral General Electromagnetic Compatibility EMCRFI Filters Ferrite Ring Dimensions 1 RFI filters DimensionsPage 1 Recommended Installation 2 Recommended installation detail inside the enclosure GE Fuji Drives USA, Inc Roanoke Blvd. Suite