GE AF-300, C11 manual Input phase failure Lin and imbalance, Connect the input wires correctly

Page 68

(9) Input phase failure (Lin) and imbalance

Lin

Are all the three phases of the

input voltage supplied?

Yes

Is the inter-phase imbalance ratio

within 2%?

Yes

Probable faulty drive. Contact

GE Fuji.

No

No

Connect the input wires correctly.

Examine the power supply system to satisfy the specification value.

-66-

Image 68

Contents AF-300 C11 TM Table of Contents Safety Instructions Page Compliance with low voltage directive in EU Drive may be dropped causing injury Instructions on useThere is a risk of fire Otherwise fire could occurInstructions on wiring Otherwise, fire could occurOtherwise electric shock or fire could occur Otherwise electric shock could occurInstructions on operation Otherwise accident could occurThere is a risk of accidents Otherwise burns could occurGeneral instructions Instruction on maintenance/inspection, and replacementOtherwise electric shock or injury could occur Preface Input Phases HorsepowerFactory Installed Options GE Product Code AF-300 Drive Family Input Voltage230VAC, 3 phase, 50/60Hz Input 230VAC, Single phase, 50/60Hz InputBefore Using This Product Receiving InspectionsAppearance Handling the Product Storage precautions CarryingStorage and transportation 1 Storage and transportation environmentInstallation and Connection 10 cmAF-300C11 1 Operating environmentOtherwise electric shock and fire could occur 1Basic connectionConnection Connecting the main circuit and ground terminals 1 Functions of main circuit and ground terminalsCutting of barrier -3-2 Connection of DC reactor Connecting the control terminalsConnection diagram 4 Surge absorber connection diagram 7 Control terminal block arrangement 2 Functions of control circuit terminals FWDDX+ Connection examples 200 to 50/60Hz Mccb Fuse Connection to PLC when analog signal is input from PLC Harmonic component NoiseLeakage current OthersOperation Inspection and Preparation before OperationOperation Method 1 General operation method1 Running command Trial RunKeypad Panel Names and FunctionsOperating Keypad Panel Is pressed at the same time asProcedure Display Press Function Selection List 1 Table of Function Selection List Selecting FunctionFundamental functions Carrier freq 75kHz is set when 0 is specified Sound tone Voltage adjust30Ry operation mode Excited when tripped Normally excited To 10.0minExtension Terminal Functions Control Functions of FrequencyX3 terminal function Tions Jump frequencyMotor Parameters High Performance FunctionsOptional Functions Serial communication optionF00 Data protection F01Details of Each Function Otherwise injuries could occurKey is pressed and decelerates-to-stop when F02 Operation methodMotor runs when GE Start Software Selection During Terminal Operation F03 Maximum output frequency This function sets the maximum output frequencyF04 Base frequency F05F06 F07Electronic thermal O/L relayLevel F09 Torque boostF10 F11 Electronic thermal O/L relay Select F12 Electronic thermal O/L relay thermal time constant Operating time? ì? ? ŒcharacteristicsÀ Á Set with F12F14 Restart mode after momentary power failure Phase input Single Phase InputF15 Frequency limiter High F16 Frequency limiter LowF17 Gain For frequency setting signal F18 Bias frequencyBias positive Bias negative 20mAdcF22 DC injection brakeBraking time F20 DC injection brake Starting frequencyF21 F23 Starting frequency F25 Stop frequencyF24 F26 Motor sound carrier freqF31 FM terminal Function F30 FM terminal voltage adjustF27 Motor sound sound tone F36 30Ry operation mode Normal Tripped OperationE01 E02 E03 X1 terminal functionX2 terminal function X3 terminal functionFrom previous C07 Multistep frequency setting P00 Motor characteristicsC01 C02 C03 Jump frequency 1, 2 C04 Jump frequency HysteresisH01 Operation time H02 Trip historyH04 Auto Reset H20 PID control Mode selectData initialization H03H21 PID control Feedback signal H22 PID control P-gainH23 PID control I-gain H25 PID control Feedback filterOptional RS485 serial communication unit O00 Option selectionRS485 RTU communication 1 List of Protective Functions Protective FunctionList of protective functions Alarm Reset Keypad panel Normal display Alarm display DisplayAlarm output Trip Otherwise fire could occurLoad excessive? TroubleshootingCase of tripping Power supply voltage within specified value? Does OU activate when load is removedConsider using DC OvervoltageOUHeat sink overheat- ing OH1 Is electronic thermal O/L relay setting correct? Drive overload OLU or motor overload OLProbable faulty drive. Contact GE Fuji Set o00 to Noise source nearby?Input phase failure Lin and imbalance Connect the input wires correctlyMotor does not start When motor rotates but the speed does not change Setting too low?When motor stalls during acceleration Motor generates ab Function change is disabled Normal heatTo 0? Set F00 toMaintenance and Inspection Daily InspectionPeriodic Inspection There is danger of electric shockElectrolyte leakage Visual Not abnormal 1 Periodic inspection listDiscoloration and distortion Visual Not abnormal More Overheating? Is off 2Tighten more 3Visual inspection Three-phase Single -phaseElectrical measurements in the Main Circuit 1 Meter for measuring the main circuitCase of 3-phase input series Input series+ + Motor SupplyInquiries about Products and Product Warranty 6Warranty Service Warranty CoverageIN-WARRANTY Failure Checklist Specifications Standard SpecificationsDrive output capacity kVA at Common specifications RUN StopPage Page Page Dimensions 00.2 2 68 17.2 D 00.2 Terminal Terminal 1 M2.5 00.2 2 External Options 1 External Options OptionsBuilt-in Options Applicable DC reactors Connection methodPrecautions Compliance with standardsGeneral L1/L L2/N L1/R L2/S L3/T P1 + N- U THR CMGeneral RFI Filters Electromagnetic Compatibility EMCGeneral 1 RFI filters Dimensions Ferrite Ring DimensionsPage 1 Recommended Installation 2 Recommended installation detail inside the enclosure GE Fuji Drives USA, Inc Roanoke Blvd. Suite