Sterling 30RA010-055 manual Temp

Page 64

Table 33 — 5K Thermistor Temperatures (°F) vs. Resistance/Voltage Drop

(Voltage Drop for Entering, Leaving Water and Outside-Air Thermistors T1, T2, T9)

	TEMP	VOLTAGE	RESISTANCE
	TEMP	DROP	RESISTANCE
	(F)	DROP	(Ohms)
	(F)	(V)	(Ohms)
		(V)
	–25	3.699	98,010
	–24	3.689	94,707
	–23	3.679	91,522
	–22	3.668	88,449
	–21	3.658	85,486
	–20	3.647	82,627
	–19	3.636	79,871
	–18	3.624	77,212
	–17	3.613	74,648
	–16	3.601	72,175
	–15	3.588	69,790
	–14	3.576	67,490
	–13	3.563	65,272
	–12	3.550	63,133
	–11	3.536	61,070
	–10	3.523	59,081
	–9	3.509	57,162
	–8	3.494	55,311
	–7	3.480	53,526
	–6	3.465	51,804
	–5	3.450	50,143
	–4	3.434	48,541
	–3	3.418	46,996
	–2	3.402	45,505
	–1	3.386	44,066
	0	3.369	42,679
	1	3.352	41,339
	2	3.335	40,047
	3	3.317	38,800
	4	3.299	37,596
	5	3.281	36,435
	6	3.262	35,313
	7	3.243	34,231
	8	3.224	33,185
	9	3.205	32,176
	10	3.185	31,202
	11	3.165	30,260
	12	3.145	29,351
	13	3.124	28,473
	14	3.103	27,624
	15	3.082	26,804
	16	3.060	26,011
	17	3.038	25,245
	18	3.016	24,505
	19	2.994	23,789
	20	2.972	23,096
	21	2.949	22,427
	22	2.926	21,779
	23	2.903	21,153
	24	2.879	20,547
	25	2.856	19,960
	26	2.832	19,393
	27	2.808	18,843
	28	2.784	18,311
	29	2.759	17,796
	30	2.735	17,297
	31	2.710	16,814
	32	2.685	16,346
	33	2.660	15,892
	34	2.634	15,453
	35	2.609	15,027
	36	2.583	14,614
	37	2.558	14,214
	38	2.532	13,826
	39	2.506	13,449
	40	2.480	13,084
	41	2.454	12,730
	42	2.428	12,387
	43	2.402	12,053
	44	2.376	11,730
	45	2.349	11,416
	46	2.323	11,112
	47	2.296	10,816
	48	2.270	10,529
	49	2.244	10,250
	50	2.217	9,979
	51	2.191	9,717
	52	2.165	9,461
	53	2.138	9,213
	54	2.112	8,973
	55	2.086	8,739
	56	2.060	8,511
	57	2.034	8,291
	58	2.008	8,076

	TEMP	VOLTAGE	RESISTANCE
	TEMP	DROP	RESISTANCE
	(F)	DROP	(Ohms)
	(F)	(V)	(Ohms)
		(V)
	59	1.982	7,686
	60	1.956	7,665
	61	1.930	7,468
	62	1.905	7,277
	63	1.879	7,091
	64	1.854	6,911
	65	1.829	6,735
	66	1.804	6,564
	67	1.779	6,399
	68	1.754	6,238
	69	1.729	6,081
	70	1.705	5,929
	71	1.681	5,781
	72	1.656	5,637
	73	1.632	5,497
	74	1.609	5,361
	75	1.585	5,229
	76	1.562	5,101
	77	1.538	4,976
	78	1.516	4,855
	79	1.493	4,737
	80	1.470	4,622
	81	1.448	4,511
	82	1.426	4,403
	83	1.404	4,298
	84	1.382	4,196
	85	1.361	4,096
	86	1.340	4,000
	87	1.319	3,906
	88	1.298	3,814
	89	1.278	3,726
	90	1.257	3,640
	91	1.237	3,556
	92	1.217	3,474
	93	1.198	3,395
	94	1.179	3,318
	95	1.160	3,243
	96	1.141	3,170
	97	1.122	3,099
	98	1.104	3,031
	99	1.086	2,964
	100	1.068	2,898
	101	1.051	2,835
	102	1.033	2,773
	103	1.016	2,713
	104	0.999	2,655
	105	0.983	2,597
	106	0.966	2,542
	107	0.950	2,488
	108	0.934	2,436
	109	0.918	2,385
	110	0.903	2,335
	111	0.888	2,286
	112	0.873	2,239
	113	0.858	2,192
	114	0.843	2,147
	115	0.829	2,103
	116	0.815	2,060
	117	0.801	2,018
	118	0.787	1,977
	119	0.774	1,937
	120	0.761	1,898
	121	0.748	1,860
	122	0.735	1,822
	123	0.723	1,786
	124	0.710	1,750
	125	0.698	1,715
	126	0.686	1,680
	127	0.674	1,647
	128	0.663	1,614
	129	0.651	1,582
	130	0.640	1,550
	131	0.629	1,519
	132	0.618	1,489
	133	0.608	1,459
	134	0.597	1,430
	135	0.587	1,401
	136	0.577	1,373
	137	0.567	1,345
	138	0.557	1,318
	139	0.548	1,291
	140	0.538	1,265
	141	0.529	1,240
	142	0.520	1,214

	TEMP	VOLTAGE	RESISTANCE
	TEMP	DROP	RESISTANCE
	(F)	DROP	(Ohms)
	(F)	(V)	(Ohms)
		(V)
	143	0.511	1,190
	144	0.502	1,165
	145	0.494	1,141
	146	0.485	1,118
	147	0.477	1,095
	148	0.469	1,072
	149	0.461	1,050
	150	0.453	1,029
	151	0.445	1,007
	152	0.438	986
	153	0.430	965
	154	0.423	945
	155	0.416	925
	156	0.408	906
	157	0.402	887
	158	0.395	868
	159	0.388	850
	160	0.381	832
	161	0.375	815
	162	0.369	798
	163	0.362	782
	164	0.356	765
	165	0.350	750
	166	0.344	734
	167	0.339	719
	168	0.333	705
	169	0.327	690
	170	0.322	677
	171	0.317	663
	172	0.311	650
	173	0.306	638
	174	0.301	626
	175	0.296	614
	176	0.291	602
	177	0.286	591
	178	0.282	581
	179	0.277	570
	180	0.272	561
	181	0.268	551
	182	0.264	542
	183	0.259	533
	184	0.255	524
	185	0.251	516
	186	0.247	508
	187	0.243	501
	188	0.239	494
	189	0.235	487
	190	0.231	480
	191	0.228	473
	192	0.224	467
	193	0.220	461
	194	0.217	456
	195	0.213	450
	196	0.210	445
	197	0.206	439
	198	0.203	434
	199	0.200	429
	200	0.197	424
	201	0.194	419
	202	0.191	415
	203	0.188	410
	204	0.185	405
	205	0.182	401
	206	0.179	396
	207	0.176	391
	208	0.173	386
	209	0.171	382
	210	0.168	377
	211	0.165	372
	212	0.163	367
	213	0.160	361
	214	0.158	356
	215	0.155	350
	216	0.153	344
	217	0.151	338
	218	0.148	332
	219	0.146	325
	220	0.144	318
	221	0.142	311
	222	0.140	304
	223	0.138	297
	224	0.135	289
	225	0.133	282

64

Image 64

Contents SAFETY CONSIDERATIONS CONTENTS GENERALMAJOR SYSTEM COMPONENTS Control Module CommunicationSterlco Comfort Network SCN Interface — Table 1 — Unit SizesTable 3 — Status Switches Table 5 - SCN Communication Bus WiringTable 2 — Thermistor Designations Table 4 - Output RelaysLEGEND FOR FIG. Page Page Fig. 3 — Wiring Schematic 30RA010-018 30RA010-018AQUA SNAPFig. 3 - Wiring Schematic 30RA010-018cont AQUA-SNAPLOW VOLTAGE CONTROL SCHEMATICSEE NOTE SEE NOTE Fig. 4 - Wiring Schematic 30RA022-030 30RA022-030AQUA SNAPFig. 4 - Wiring Schematic 30RA022-030cont AQUA-SNAPLOW VOLTAGE CONTROL SCHEMATICFig. 5 — Wiring Schematic 30RA032-040 30RA032-040AQUA SNAPFig. 5 — Wiring Schematic 30RA032-040cont AQUA-SNAPLOW VOLTAGE CONTROL SCHEMATICFig. 6 — Wiring Schematic 30RA042-055 30RA042-055AQUA SNAPFig. 6 — Wiring Schematic 30RA042-055cont AQUA-SNAPLOW VOLTAGE CONTROL SCHEMATICFig. 7 — Main Base Board ESCAPEENTERREMOTE CONTACT SW1 OFF ENABLE OFF SW2 ON MODEFig. 9 — Typical Space Temperature Sensor Wiring Fig. 11 - Energy Management Module CEPL130351100/100 Fig. 12 — Deadband Multiplier R-22Maneurop Compressor Fig. 13 — Operating Envelope forFig. 14 — 30RA Condenser Fan Sequence Cooling Set Point Select Service Test See Table 11 — Both main power and control circuit power must be onTable 8 — Control Methods and Cooling Set Points Fig. 16 — Scrolling Marquee DisplayOptional Factory-InstalledHydronic Package — •Cooler Pump Control CPC Configuration, OPT1 ON Fig. 17 — Dual Chiller Thermistor Location Table 9 — Marquee Display Menu StructureTable 10 — Run Status Mode and Sub-ModeDirectory SUB-MODE Table 12 - Temperature Mode and Sub-ModeDirectory Table 14 — Set Point and Sub-ModeDirectory Table 13 — Pressure Mode and Sub-ModeDirectoryTable 15 — Inputs Mode and Sub-ModeDirectory Table 16 — Outputs Mode and Sub-ModeDirectory SUB-MODEKEYPAD DISPLAYSUB-MODE KEYPADITEM DISPLAYSUB-MODE KEYPADITEM DISPLAYTable 18 — Time Clock Mode and Sub-ModeDirectory PER.3 SUB-MODE Table 20 — Alarms Mode and Sub-ModeDirectory Table 19 — Operating Mode and Sub-ModeDirectorySUB-MODE ITEMKEYPAD ENTRY DISPLAYRSET DISP Table 23 — Operating Modes Table 24 — Example of Reading and Clearing Alarms Table 25A — 4-20mA ResetTable 26B — Configuring Return Temperature Reset Fig. 18 — Standard Chilled Fluid Temperature Control — No ResetFig. 19 — Outdoor-AirTemperature Reset Fig. 20 — Space Temperature ResetFig. 21A — 4- to 20-mADemand Limiting Fig. 21B — Cooling Set Point 4 to 20 mATROUBLESHOOTING Table 27 — Configuring Demand LimitRecommended that system be filled with an appro Table 28 — Troubleshootingand fluid tubing Fig. 22 — Component Arrangement — 30RA010-030 FU — Fuse GND — GroundFig. 23 — Component Arrangement — 30RA032-040 FU — Fuse GND — GroundFig. 24 — Component Arrangement — 30RA042-055 FU — Fuse GND — GroundNOTES LEGEND Table 29 — Alarm and Alert Codes Table 29 - Alarm and Alert Codes cont Table 29 — Alarm and Alert Codes cont ALARMTable 29 — Alarm and Alert Codes cont ALARMTable 29 — Alarm and Alert Codes cont ALARMSERVICE Compressor Replacement Refer to FigTable 30 - Unit Torque Specification Electronic ComponentsFig. 28 — Compressor Wiring Fig. 27 — Typical Compressor Mounting — All SizesFig. 29 — Compressor Location — 30RA010-030 Fig. 30 — Compressor Location — 30RA032-055Condenser Section and Coils Table 31 - Oil ChargeFig. 31 — 30RA Access Panels Check Refrigerant Feed ComponentsFig. 32 — Condenser-FanMounting Fig. 33 — Condenser-FanPosition Standard FanTable 32 — Factory Settings, High-Pressure Switch FixedCompressor and Unit Protective Devices Check Unit SafetiesCOOLER FREEZE-UPPROTECTION TEMP TEMP For Thermistor T10 For Thermistor T10 Fig. 35 — Fluid-SideTemperature Sensors T1 and T2 Main Base Board, J8 ConnectorFig. 36 — Thermistor Connections to PROGRAMMING Mode •P50: FAULT HISTORY — Last 8 faults Table 37 - Fault Codes•P51: SOFTWARE version PARAMETERS Table 39 — Replacement Modules MAINTENANCE Minimum Loop VolumePRE-START-UP System CheckOperating Limitations Table 41 — Temperature Limits for OPERATION SEQUENCEStandard 30RA Units APPENDIX A SCN Tables A_UNIT General Unit ParametersCIRCADIO Circuit A Discrete Inputs/Outputs CIRCA_AN Circuit A Analog ParametersCIRCB_AN Circuit B Analog Parameters CIRCBDIO Circuit B Discrete Inputs/OutputsOPTIONS Unit Parameters ALARMDEF Alarm Definition Table DISPLAY Marquee Display SETUPDUALCHIL Dual Chiller Configuration Settings BRODEFS Broadcast POC Definition TableOPTIONS1 Options 1 Configuration OPTIONS2 Options 2 ConfigurationRESETCON Temperature Reset and Demand Limit SCHEDOVR Timed Override SetupSETPOINT UNIT ALARMS: Maintenance DisplayMAINTENANCE CURRMODS: Maintenance Display DUALCHIL: Maintenance DisplayLEARNFNS Maintenance Display LOADFACT: Maintenance DisplayPM-PUMP:Maintenance Display PM-COIL:Maintenance DisplayPM-STRN Maintenance Display RUNTEST: Maintenance Display TESTMODE: Maintenance Display STRTHOUR Maintenance DisplayVERSIONS: Maintenance Display WSMDEFME: Maintenance Display APPENDIX B FACTORY SETTINGS FOR COMPRESSOR, FAN, PUMPAND MANUAL STARTERS AND MANUAL STARTERS cont FACTORY SETTINGS FOR COMPRESSOR, FAN, PUMPAPPENDIX C DataPort, DataLink, BAClink Object DefinitionOPTIONS SETPOINTSTART-UPCHECKLIST FOR 30RA LIQUID CHILLER Remove and use for Job File I.Project InformationII. Preliminary Equipment Check Design InformationIII. Unit Start-Up Start and Operate Machine. Complete the FollowingCL-3 COMMENTS Record Software Versions MODE — RUN STATUSCL-4 OPTIONS1 Options Configuration UNIT Configuration SettingsIII.Unit Start-Upcont OPTIONS2 Options Configuration RSET Reset Configuration SettingsIII.Unit Start-Upcont CL-6SLCT Setpoint and Ramp Load Configuration III.Unit Start-UpcontSETPOINT CL-7Service Test Mode and Sub-ModeDirectory III.Unit Start-Upcont