Sterling 30RA010-055 manual Parameters

Table 38 — Motormaster® V Program Parameters for Operating Modes

PARAMETERS		DESCRIPTION	MODE	MODE	MODE	MODE
			1	2	3	4
	P01	Line Voltage: 01 = low line, 02 = high line	01	02	01	02
	P02	Sterlco Freq: 01 = 4 kHz, 02 = 6 kHz, 03 = 8 kHz	01	01	01	01
	P03	Startup mode: flying restart	06	06	06	06
	P04	Stop mode: coast to stop	01	01	01	01
	P05	Standard Speed source: 01= keypad,	05	05	05	05
		04=4-20mA (NO PI), 05= R22, 06=R134a
	P06	TB-14 output: 01 = none	01	01	01	01
	P08	TB-30 output: 01 = none	01	01	01	01
	P09	TB-31 Output: 01 = none	01	01	01	01
	P10	TB-13A function sel: 01 = none	01	01	01	01
	P11	TB-13B function sel: 01 = none	01	01	01	01
	P12	TB-13C function sel: 01 = none	01	01	01	01
	P13	TB-15 output: 01 = none	01	01	01	01
	P14	Control: 01 = Terminal strip	01	01	01	01
	P15	Serial link: 02 = enabled 9600,8,N,2 with timer	02	02	02	02
	P16	Units editing: 02 = whole units	02	02	02	02
	P17	Rotation: 01 = forward only, 03 = reverse only	01	01	01	01
	P19	Acceleration time: 10 sec	10	10	10	10
	P20	Deceleration time: 10 sec	10	10	10	10
	P21	DC brake time: 0	0	0	0	0
	P22	DC BRAKE VOLTAGE 0%	0	0	0	0
	P23	Min freq = 8 Hz ~ 100 – 160 rpm	8	8	8	8
	P24	Max freq	60	60	50	50
	P25	Current limit: (%)	125	110	125	110
	P26	Motor overload: 100	100	100	100	100
	P27	Base freq: 60 or 50 Hz	60	60	50	50
	P28	Fixed boost: 0.5% at low frequencies	0.5	0.5	0.5	0.5
	P29	Accel boost: 0%	0	0	0	0
	P30	Slip compensation: 0%	0	0	0	0
	P31	Preset spd #1: speed if loss of control signal	57	57	47	47
	P32	Preset spd #2: 0	0	0	0	0
	P33	Preset spd #3: 0	0	0	0	0
	P34	Preset spd 4 default — R22 set point.	18.0	18.0	18.0	18.0
		TB12-2 open
	P35	Preset spd 5 default — R134a set point.	12.6	12.6	12.6	12.6
		TB12-2 closed
	P36	Preset spd 6 default	0	0	0	0
	P37	Preset spd 7 default	0	0	0	0
	P38	Skip bandwidth	0	0	0	0
	P39	Speed scaling	0	0	0	0
	P40	Frequency scaling 50 or 60 Hz	60	60	50	50
	P41	Load scaling: default (not used so NA)	200	200	200	200
	P42	Accel/decel #2: default (not used so NA)	60	60	60	60
	P43	Serial address	1	1	1	1
	P44	Password:111	111	111	111	111
	P45	Speed at min signal: 8 Hz; used when PID	8	8	8	8
		mode is disabled and 4-20mA input is at 4 mA
	P46	Speed at max feedback: 60 or 50 Hz. Used	60	60	50	50
		when PID disabled and 4-20mA input is at 20 mA
	P47	Clear history? 01 = maintain. (set to 02 to clear)	01	01	01	01
	P48	Program selection: Program 1 – 12	01	02	03	04
	P61	PI Mode: 05= reverse, 0-5V, 01 = no PID	05	05	05	05
	P62	Min feedback = 0 (0V *10)	0	0	0	0
	P63	Max feedback = 50 (5V * 10)	50	50	50	50
	P64	Proportional gain = 4%	4	4	4	4
	P65	Integral gain = .2	.2	.2	.2	.2
	P66	PI acell/decel (set point change filter) = 5	5	5	5	5
	P67	Min alarm	0	0	0	0
	P68	Max alarm	0	0	0	0
	LEGEND
NA	— Not Applicable
PID	— Proportional Integral Derivative
TB	— Terminal Block

72