Cornelius 3 service manual Condenser FAN Motor Replacement, Compressor Replacement

Page 63

Viper Service Manual

Table 49

Step

Procedure

8Install the check valve on the new valve and solenoid.

9Remove the valve and solenoid from the mounting bracket and replace it.

10 Reverse the procedure to reinstall the bracket into the unit. 11 Reconnect power to the unit and test the system.

CONDENSER FAN MOTOR REPLACEMENT

The fan motor is located on the top of the unit, as shown in Figure 49. If the motor needs replacement, perform the procedure in Table 50 to remove and reinstall a motor.

Locking

Locking

Nuts

 

Nuts

 

Figure 49. Condenser Fan Mounting Nuts

 

Table 50

 

 

Step

Action

 

 

 

 

1

Disconnect power from the unit.

2

Disconnect the fan by unplugging the connector.

 

 

3

Remove the four locking nuts securing the fan to the top of the condenser.

 

 

4

Lift the fan and shroud off the unit.

 

 

5

Remove the four screws and washers securing the fan to the shroud.

 

 

6

Replace the fan.

 

 

7

Reverse the procedure to install the new fan.

 

 

8

Reconnect power to the unit.

 

 

 

 

COMPRESSOR REPLACEMENT

Caution should be used when working with refrigerants. To replace a compres- sor, perform the procedure in Table 51.

NOTE: Be sure to reclaim refrigerant when replacing compressor.

© 2010, IMI Cornelius Inc.

- 57 -

Publication Number: 621360041TBSER

Image 63
Contents Fruitista Viper 3 Flavor Trademarks and Copyrights Contact InformationSafety Instructions IntroductionSystem Overview Operation Preventative Maintenance Component ReplacementTroubleshooting Page Manual Overview IntroductionDifferent Types of Alerts Read and Follow ALL Safety InstructionsSafety Tips Safety OverviewCO2 Carbon Dioxide Warning Qualified Service PersonnelSafety Precautions Shipping and StorageOverrun, as Applied to Carbonated Beverages Mounting in or on a CounterDispensed Product Conditions Brix Affects Overrun Low Dispensing Volume Affects Overrun Introduction System OverviewTheory of Operation Fruitista Viper System 3-Barrel Refrigeration SchematicFruitista Viper 3-Barrel Wiring Diagram Typical Bulk Cylinder CO2 Connection CO2 SystemPsig Settings Syrup Viscosity CO 2 Setting Expansion Type SetBarrel System Schematic Control Panel Water SystemSyrup System IntroductionStatus Control Panel DisplayControl Panel Buttons BarrelSoftware Structure Button Description System MenusMain Menu Control Panel Menu DescriptionsUnit Data Menu Error Status Menu Error Type DescriptionDisplayed Action Type Description Message Comm ERR IO BRL RecoverFill Error ResetError Log Menu Setup MenuClock Setup Menu Setting the ClockAction Procedure Step Action Procedure Setting Daylight Sav- ings TimeEvents Setup Menu Event DAY SUN Setup SleepWakeup Setting the Sleep Wakeup Times Setting EventsSetting Defrost Lockout Viscosity Setup MenuDefrost Lock CO2 Setup Menu ViscCO2 USA Euro Option Setup MenuOption Temp Format Setup Date Format Time FormatSetting the Type of Syrup Maintenance MenuSetting the Temperature Format Setting the Date Format Setting the Time Format Setting the POS Light- ingSelect Barrel Maint Manual Diag Totals Barrel Maintenance Menu Purging a BarrelBrix Setup Motor SetupFilling a Barrel Run the Barrel MotorRinsing a Barrel Noid for a barrel to prevent damage from occurring Manual Diagnostic MenuSystem Open. The software is designed to turn on the hot gas soleDisplay Value Description Totals MenuBrix Setup Menu Brix Brix Setup ScreenMotor Setup Menu Eeprom is not installed or is faultyMotor Type CAL Calibrating a MotorSystem Menu Security Pressure SensorsNone LOW High Both Unit Line Voltage LOW Psig #1High Psig #1 Dispensed Product Throughput Maintaining Product QualityViper Viscosity Programmed Defrost Scheduling Viscosity SettingCO2 Setting Sleep Mode Recom- mendationsStarting the Unit Summary Preventative MaintenanceCleaning Air Filter Monthly MaintenanceStep Action Cleaning the Syrup Connections SEMI-ANNUAL MaintenanceInspecting and Replacing Scraper Blades Self-Closing Dispensing Valve Servicing Motorman Dispensing ValvesEmptying a Barrel Sanitizing the SystemProduct position Flushing the System of Syrup Sanitizing the BarrelPpm available chlorine Step Procedure Cleaning the Water FilterRemoving the Existing Seal Barrel Motor Seal ReplacementView of Motor Shaft with Spacer on Shaft Installing a New SealMotor Seal Leak Test Barrel Motor ReplacementView of Motor Run Capacitors Step Motor RUN Capacitor ReplacementRear View of Water Pump Water Pump ReplacementSide View of CO2 Pulse Valves CO2 Pulse Valve ReplacementView of Shutoff Solenoids w/ Access Panel Removed Syrup and Water Shutoff Solenoid ReplacementCompressor Replacement Condenser FAN Motor ReplacementHot Gas Solenoid 1 per barrel HOT GAS Solenoid ReplacementSyrup Pressure Switch Replacement Liquid Line Solenoid ReplacementView of Syrup Pressure Switch and Valve Water Pressure Switch ReplacementView of Display Board Display Board ReplacementSoftware Compatibility Control Board ReplacementView of Motor Board in E-Box Motor Board ReplacementProblem Probable Cause Remedy Troubleshooting the SystemTroubleshooting Product Not Cold Publication Number 621360041TBSER 2010, IMI Cornelius Inc Page IMI Cornelius Inc

3 specifications

Cornelius 3 is a cutting-edge platform designed to enhance communication and collaboration in the ever-evolving landscape of digital interaction. With an impressive range of features, technologies, and characteristics, it stands out as a vital tool for organizations looking to streamline their operations and enhance productivity.

One of the most notable features of Cornelius 3 is its intuitive user interface. Designed with user experience in mind, it provides a seamless navigation experience, enabling users to access various functionalities with ease. This ensures that both technical and non-technical users can quickly adapt to the platform without extensive training.

Cornelius 3 incorporates advanced artificial intelligence (AI) capabilities, enhancing the platform's effectiveness in facilitating communication. Its AI-driven algorithms analyze user interactions, providing tailored recommendations and insights that improve decision-making processes. This intelligent system is designed to learn from user behaviors, continually optimizing its responses and functionalities to suit individual and organizational needs.

The platform also boasts robust integration capabilities, allowing organizations to connect with a wide range of third-party applications. This flexibility is crucial in today’s interconnected environment, as businesses often utilize multiple tools to manage their operations. With Cornelius 3, users can consolidate their workflows and eliminate the need to switch between various applications, thus saving time and reducing operational friction.

Collaboration is further enhanced through Cornelius 3’s real-time communication tools. These include chat features, video conferencing, and collaborative document editing, empowering teams to work together seamlessly regardless of their geographical locations. This real-time functionality promotes quicker feedback loops and fosters a culture of collaboration that is essential in a work-from-anywhere world.

Security and data privacy are paramount in today’s digital age, and Cornelius 3 addresses these concerns with robust security features. Advanced encryption methods protect user data, and strict access controls ensure that sensitive information is only accessible to authorized personnel. This commitment to security builds trust among users and compliance with relevant regulations.

In conclusion, Cornelius 3 is a powerful platform that combines a user-friendly interface, advanced AI capabilities, seamless integration, real-time collaboration tools, and top-notch security features. These characteristics make it an invaluable asset for organizations looking to enhance their communication and operational efficiency in a digital-first landscape. With Cornelius 3, businesses can empower their teams, drive innovation, and achieve their goals more effectively.