Blodgett SHO-G manual General Guidelines for Operating Personnel, Operating Tips

Page 22

Operation

General Guidelines for Operating Personnel

COOK TIMES AND TEMPERATURES Preheating the oven

Always preheat the oven before baking or roast- ing. We recommend preheating 50_F (10_C) above the cook temperature to offset the drop in temperature when the doors are opened and cold product is loaded into the oven. Set the thermostat to the cook temperature after the product is loaded.

NOTE: For frozen product, preheat the oven 100_F (38_C) above the cook tempera- ture.

Cook Temperatures

Generally, cook temperatures should be 50_F (10_C) lower than deck or range oven recipes. If the edges of the product are done but the center is raw, or if there is color variation, reduce the ther- mostat setting another 15---25_F (10---15_C). Con- tinue to reduce the cook temperature on succes- sive loads until the desired results are achieved.

NOTE: Cooking at excessive temperatures will not reduce cook time, it will produce un- satisfactory baking and roasting results.

Cook Time

Check the product in about half the time recom- mended for deck or range oven recipes. Record times and temperatures which provide best re- sults for future reference.

NOTE: Cook time will vary with the amount of product loaded, the type of pan and the temperature.

OPERATING TIPS

Pans and Racks

Product or pan height determines how many racks are used. The oven holds up to ten 18” x 26” (45.7 x 66.0 cm) bun pans.

Load the oven from the bottom, centering the pans on the rack. Never place a pan or aluminum foil on the bottom of the oven. This obstructs the flow of air and results in uneven baking and roasting.

Roasting

To reduce shrinkage when roasting, place meat directly on the racks. Place a sheet pan one-half full of water in the bottom rack position. The water evaporates, increasing humidity in the oven chamber. The pan catches grease from the meat, making oven cleaning easier.

Baking

Weigh the product to ensure equal distribution in each pan. Varying amounts of product will cause uneven baking results.

Fans

The fan must be operating for the oven to heat. To avoid rippling of batter product use the following procedure.

1.Preheat the oven 25_F (15_C) above the bak- ing temperature.

2.Load the oven with product. Close the doors.

3.Set the thermostat to the baking temperature.

4.Turn the oven off.

5.Allow the product to set for 5---7 minutes with the fan off. The residual heat in the oven sets the product.

6.Turn the oven on for the remainder of the bake.

18

Page 21 Page 23
Image 22
Page 21 Page 23
Contents SHO-G Avertissement Reputation YOU can Count on Page Table of Contents/Table des Matières S Speci Fications SH1G/AB Oven Description and SpecificationsIntroduction Ca na d a a nd G e nera l Ex p o rtOven Components Delivery and Inspection InstallationDelivery and Location Oven LocationOven Assembly NSF BoltsCasters for Single and Double Stacked Ovens Caster AssemblyLEG Attachment Low Profile Casters for Double Stacked OvensDouble Section Assembly Oven Leveling Installing the canopy hood draft diverter Canadian installationsAustralia and general export installations VentilationFlue Diameter 15cm Installing the draft hoodDirect Flue Arrangement Oven Single DoubleGeneral export installations Utility Connections --- Standards and CodesGas Connection GAS PipingKPa Pressure Regulation and TestingInlet Pressure Natural Propane Manifold Pressure Natural PropaneGAS Hose Restraint Electrical Specifications Electrical ConnectionAdjustments Associated with Initial Installation Initial StartupWhat to do in the event of a power failure Safety InformationSafety Tips General safety tipsControl Description Standard ControlOperation General Guidelines for Operating Personnel Operating TipsFish and Seafood Product Temperature Time # Shelves MeatsPoultry CheeseCleaning the Oven MaintenanceCleaning and Preventative Maintenance Preventative MaintenanceTroubleshooting Guide Possible Causes Suggested RemedySpecifications Pour GAZ -- SH1G/AB Description et Spécifications du FourÉléments du Four Livraison ET Inspection Livraison et ImplantationImplantation DU Four Montage du Four Boulons NSFRoulettes pour four simple ou pour four super- posés Assemblage DES PiedsMontage DES Roulettes Roulettes de bas profile pour deux fours super- posésAvertissement Montage DE LA Section DoubleMise À Niveau DU Four Installation du déviateur de tirage Installation aux États-- Unis et au CanadaGénéralités concernant les installations à l’ex- portation Hotte D’ÉVACUATION Type VoûteDiamètre DU Cheminée Installation de la hotte de tirageEN Prise Directe Four Simple DoubleBranchements de Service --- Normes et Codes Équipement De Service d’alimentation De Gaz siConduit DE GAZ Longeur Dimensions nominales De conduit PiedsBranchement de Gaz ExemplePression à l’entrée Gaz Naturel Gaz Propane Réglage ET Test DE PressionPression au collecteur Gaz Naturel Gaz Propane Retenue DU Tuyau DE GAZ Spécifications Électriques Raccordement ÉlectriqueEt Canada Réglages À Faire Lors DE L’INSTALLA- Tion Initiale Mise en Marche InitialeConseils DE Sécurité UtilisationInformations de Sécurité Que faire en cas de panne de secteurDescription DES Commandes Commandes standardUtilisation Consignes Générales à l’Intention des Utilasateurs ConseilsPoisson et Fruits de Mer Aliment Température Durée Étagères ViandesVolailles FromagesNettoyage DES Fours EntretienNettoyage et Entretien Préventif Entretien PréventifGuide de Détection des Pannes Causes Probables SuggestionGuide de Détection des Pannes Insert Wiring Diagram Here Placer Schéma DE Câblage ICI
Top Page Image Contents