Milwaukee 4555-22 Storing the Pressure Washer, Preparing for USE After Storage, Pump Maintenance

Page 19

MAINTENANCE

STORING THE PRESSURE WASHER

See Figures 21 - 22.

It is important to store this product in an area that will not experience freezing temperatures. Always empty water from hoses and pump, and empty fuel from the fuel tank.

NOTE: Use of a fuel stabilizer and pump saver will give you better performance and increase the life of the machine.

AFTER THE MACHINE HAS COOLED COMPLETELY: Discharge Fuel:

Drain the fuel tank completely. Stored gas can go stale in 30 days.

Engine Oil:

Drain the oil and replace with fresh, clean oil.

Spark Plug:

1.Disconnect spark plug wire and remove the spark plug. Pour about a teaspoon of clean, air-cooled, four-cycle oil through the spark plug hole into the combustion chamber.

2.Leaving the spark plug out, pull the starter cord two or three times to coat the inside of the cylinder wall.

3.Inspect the spark plug and clean or replace, as neces- sary.

4.Reinstall the spark plug, but leave the spark plug wire disconnected.

Air Filter:

1.Clean or replace the air filter according to engine manufacturer instructions. (See engine manual.)

Hoses and Pump:

Flush the injection hose with clean water for 1-2 minutes. Remove all hoses. Empty the pump by pulling on the recoil starter about 6 times. This should remove most of the liquid from the pump.

Moving Handle:

To collapse the moving handle for storage, pull and hold the release pin while pushing the handle down.

PREPARING FOR USE AFTER STORAGE

1.Pull the recoil starter grip three or four times to clean oil from the combustion chamber.

2.Remove spark plug from the cylinder. Wipe oil from the spark plug and return it to the cylinder.

3.Reconnect the spark plug wire.

4.Refuel the machine as described earlier in the opera- tor’s manual.

PUMP MAINTENANCE

We recommend having the pump oil changed every 200 hours to ensure longer life of the machine. This service should be performed by an authorized service center.

Fig. 21

TO STORE THE MACHINE

RELEASE

 

PIN

 

Fig. 22

 

page 19

Page 18 Page 20
Image 19
Page 18 Page 20
Contents OPERATOR’S Manual Read ALL Instructions General Safety RulesMachine USE and Care Specific Safety Rules Pressure Washers Symbol Signal Meaning SymbologySymbol Name DESIGNATION/EXPLANATION Functional Description Product SpecificationsSize Output Features Packing List AssemblyAttaching the Wheel Assembly UnpackingTo install the pressure/flow adjustment handle cap Installing the Frame SupportsInstalling the Wand Storage Holster To install the pump oil capAssembling the Spray Wand Connecting the High Pressure Hose to the Spray WandAttaching Injection Hose Adding Gasoline to the Fuel Tank Adding OIL to the EngineConnecting the High Pressure Hose to the Pump Connecting the Garden Hose to the Pressure WasherApplications OperationGeneral Instruction To start Starting and Stopping the Pressure WasherTo stop To engage the lock off Using the Spray Wand TriggerMoving the Pressure Washer Selecting the Correct QUICK-CONNECT Nozzle for the JOBTo connect a nozzle to the spray wand Washing with Detergent Using the Pressure WasherBefore shutting off the engine General Maintenance MaintenanceNozzle Maintenance See Figures 21 Pump MaintenanceStoring the Pressure Washer Preparing for USE After StoragePeriodic Maintenance Schedule Table AccessoriesProblem Cause Solution TroubleshootingTroubleshooting Evaporative Emission Control Warranty Statement WarrantyEmission Warranty Parts List Pressure Washer Lire Toutes LES Instructions Règles DE Sécurité GénéralesSoin ET Utilisation DE LA Machine Règles DE Sécurité Spécifiques Nettoyeur Haute Pression Symbole NOM DÉSIGNATION/EXPLICATION SymbolesDescription Fonctionnelle Fiche TechniqueCaractéristiques Liste DE Contrôle AssemblageAvertissement DéballageInstallation DE L’ÉTUI DE Remisage DE LA Lance Installation DES Supports DE CadrePour installer le bouchon d’huile de la pompe Assemblage DE LA Lance DE Pulvérisation Ajout D’ESSENCE Dans LE Réservoir DE Carburant Ajout D’HUILE MoteurLA Pompe Connexion DU Tuyau Haute Pression ÀInstructions Générales UtilisationPour arrêter Démarrage ET Arrêt DU Nettoyeur Haute PressionVoir les Figures 12 et Pour démarrerVoir les Figure Utilisation DE LA Détente DE LA Lance DE PulvérisationDéplacement DU Nettoyeur Haute Pression Lavage Avec Détergent Utilisation DU Nettoyeur Haute PressionEntretien Général EntretienEntretien DE LA Buse Voir les Figures 21 et Mise EN Service Après RemisageRemisage DU Nettoyeur Haute Pression Entretien DE LA PompeTableau D’ENTRETIEN Périodique AccessoiresTableau DE Calendrier D’ENTRETIEN Périodique Dépannage Problème Cause SolutionDépannage VOS Droits ET Obligations Dans LE Cadre DE LA Garantie GarantieExigences Concernant LES Réparations Sous Garantie Nettoyeur haute pression Peligro Reglas DE Seguridad GeneralesEmpleo Y Cuidado DE LA Máquina Reglas DE Seguridad Específicas Lavadoras a Presión Símbolo Nombre DENOMINACIÓN/EXPLICACIÓN SimbologíaSímbolo Señal Significado Peligro PrecauciónDescripción Funcional Especificaciones DEL ProductoCaracterísticas Lista DE Empaquetado ArmadoAdvertencia DesempaquetadoPara instalar la tapa del mango de ajuste de flujo/ presión Instalación DE LA Funda DE ALMACE- Namiento DEL RociadorVea la figura Para instalar la tapa del aceite de la bombaConexión DE LA Manguera DE Alta Presión AL Rociador Armado DEL RociadorConexión DE LA Manguera DE Inyección Para Añadir Gasolina AL Tanque DE Combustible Para Añadir Aceite AL MotorQuina Conexión DE LA Manguera DE Jardín a LA Lavadora a PresiónConexión DE LA Manguera DE Alta Presión a LA Bomba Para conectar la manguera de jardín a-la máUsos FuncionamientoInstrucción General Para apagar Encendido Y Apagado DE LA Lavadora a PresiónVea las figuras 12 a Para arrancarVea las figura Utilización DEL Gatillo DEL RociadorPara conectar una boquilla al rociador Traslado DE LA Lavadora a PresiónLavando CON Detergente Utilización DE LA Lavadora a PresiónAntes de apagar el motor Mantenimiento General MantenimientoMantenimiento DE LA Boquilla Mantenimiento DE LA Bomba Almacenamiento DE LA Lavadora a PresiónVea las figuras 21 Tabla DE Calendario DE Mantenimiento Periódico AccesoriosProblema Causa Solución Solución DE ProblemasBloqueos Derechos Y Obligaciones DEL Consumidor Según LA Garantía GarantíaLista DE Piezas DE Garantía DE Emisión Lavadora a presión Notas Notas Sawdust United States

4555-22 specifications

The Milwaukee 4555-22 is a powerful and innovative tool in the landscape of heavy-duty construction and renovation. Designed primarily as a wall cutter, this equipment is built to facilitate quick, precise cuts in a variety of materials, including brick, block, and concrete. One of its most appealing attributes is its formidable 15-amp motor that effortlessly generates a no-load speed of up to 4,100 RPM. This powerful motor not only enhances cutting efficiency but also extends the life of the tool through its robust design.

One of the standout features of the Milwaukee 4555-22 is its innovative adjustable depth control. This allows users to make cuts into materials with depths between 0-3 inches, making it a versatile tool suitable for diverse applications. Furthermore, the tool comes equipped with a lead screw that facilitates consistent depth settings, ensuring that users can achieve the exact depth required for their specific tasks without any guesswork.

The Milwaukee 4555-22 also boasts an ergonomic design, featuring an adjustable rear handle that provides a comfortable grip during operation. This feature is particularly invaluable for prolonged use, as it minimizes user fatigue and enhances overall control. Additionally, the integrated water feed system aids in dust management while cutting, thereby promoting a cleaner working environment and increasing visibility.

The characteristic durability of Milwaukee tools is present in the 4555-22 model. Its reinforced housing and components are engineered to withstand the rigors of heavy use on job sites, ensuring longevity and reliability. Moreover, the tool is designed for easy blade changes, allowing users to switch between blades tailored for different materials efficiently.

Another key technology featured in the Milwaukee 4555-22 is its integrated overload protection system. This feature prevents the motor from overheating during demanding tasks, thus safeguarding the tool and prolonging its operational lifespan.

In conclusion, the Milwaukee 4555-22 combines power, precision, and user-friendly design, making it an essential tool for professionals in construction and renovation. Its advanced features, from adjustable depth controls to integrated overload protection, underscore Milwaukee's commitment to innovation and quality, ensuring that users can tackle their toughest cutting tasks with confidence and ease.
Top Page Image Contents