Troubleshooting Using the Port Activity LEDs | 3Com 5104M-FL1

Troubleshooting Using the Port Activity LEDs

If a port Activity LED does not light, use the Table 4-1 to help troubleshoot the problem.

Table 4-1. Troubleshooting Using the Port Activity LEDs

	LED Name	LED	Possible Cause	Corrective Action
	LED Name	State	Possible Cause	Corrective Action
		State

	Activity	Off	There is no traffic	None.
	(Ports)		received from the
	1 - 4)		segment.
	1 - 4)

			Port is disabled.	Enable the port.

			Power is off.	Check the Controller
				Module Power LED.

			Activity LED has burnt	Press the LED check
			out.	button on the
				Controller Module.

			10BASE-FL Module	Connect the cable
			port is faulty.	to a different port.

			10BASE-FL Module is	Try a different
			faulty.	10BASE-FL Module.

			Backplane connection	Reinsert the
			is bad.	10BASE-FLModule.If
				this fails, try another
				concentrator slot.

4 - 2 ONline Ethernet 10BASE-FL Installation and Operation Guide

Image 78

3Com 5104M-FL1 Troubleshooting Using the Port Activity LEDs, LED Name, Possible Cause Corrective Action State

Contents

Page Vcci Class 1 Compliance Page Page Contents Installing and Operating the Module Appendix a Specifications Page Figures Page Tables Page How to Use This Guide Audience Structure of This Guide Document Conventions Text ConventionsText Convention Example Related Documents 3Com Documents Reference Documents Page Introduction 10BASE-FL Module Description BASE-F Standards 10BASE-FL and Foirl Ieee Standards ComparisonTheory of Operation 10BASE-F Standard Description BASE-FL Module Connections Designing and ExpandingtheNetwork Seven Basic Network Rules Understanding the General RulesBasic Network Rules Rule Definition Recommendations/Notes As equivalent distance. Every Assume that one LAN Equivalence LAN Product Equivalent DistancesLAN Product Equivalent Determining Maximum 10BASE-FL Link Distances Calculating Maximum Link Distance Determining Link Budget DBm BASE-FL Module Optical Power BudgetCable Size Transmit Receive Optical Link Loss Power ONline to Splicing Typical Fiber Loss Characteristics Connector and Splice Insertion LossConnector Type Range of Loss Per Typical Loss dB Pair dB Splice Type Range of Loss dB Typical Loss dB Example Fiber Link With Mechanical Splice Meter Fiber Link With Mechanical Splice Example Fiber Link Through Patch Panels Meter Fiber Link Through Two Patch Panels Star Configuration Choosing a Network Backbone Cabling Structure Serial Configuration Star-Wiring Configuration 10BASE-FL Module Configurations Serial Configuration Using 10BASE-FL Modules 10BASE-FL Backbone, 10BASE-FL to-the-Desk All-10BASE-FL Network with 3 Concentrators Example a Network with 3 Concentrators Example a Network with 6 Concentrators Network with 6 Concentrators Total Fiber Number Equivalent 10BASE-FL Backbone, Unshielded Twisted Pair to-the-DeskFiber Equivalent Distances Between Transceivers Path Example Sample Configuration Distance Calculation Sample Configuration Distance Calculation 10BASE-FB Fiber Backbone, 10BASE-FL to-the-Desk Sample Fiber Backbone, 10BASE-FL to-the-Desk Configuration Example Fiber Backbone, 10BASE-FL to-the-Desk Connecting External Network Devices Example Connecting a Thin Ethernet 10BASE2 Segment Ieee Designing and Expanding the Network 2 Fault-Tolerant Configurations Configuring Ports for Fault ToleranceStandard Redundant Configuration In this configuration Implementing Backbone Cable Plant Fault Tolerance Setting Redundancy 10. Redundant Fiber Backbone Configuration Remote Failure Signaling Implementing Total Backbone Fault Tolerance 11. Total Backbone Fault-Tolerant Configuration 12. Network With 3 Concentrators ONline Ethernet 10BASE-FL Installation and Operation Guide Installing and Operating the Module Precautionary Procedures Unpacking Procedures Quick Installation Quick Installation ProceduresStep Procedure Section Title Setting the Dip Switches Setting Dip Switch SW1 BASE-FL Module Dip Switch Locations Dip Switch SW1 Settings Factory Switch SettingFunction Off Default Setting Dip Switch SW2 Dip Switch SW2 Settings for Switches 1 toSwitch Function Factory Default Switch Settings Installing the ModuleDip Switch SW2 Settings for Switches 5 Channel Selection Installing the 10BASE-FL Module BASE-FL Module Connection Configuring the Module Enabling Ports Selecting a Network Enabling Port Redundancy SET Port slot.port Mode Redundant slot.port Enabling Remote Failure Signaling BASE-FL Modules Connected with Redundancy/RFS Enabled Showing Module Configuration Saving Module Configuration Shows the location of these indicators Monitoring the Front Panel BASE-FL Module Faceplate and ONline System Concentrator Interpreting the 10BASE-FL Module LEDs LED Name Color State Indicates LED State Module Is Configured for Verifying the LED and Network AssignmentsNetwork Check Codes Troubleshooting LED Name Troubleshooting Using the Port Activity LEDsTroubleshooting Using the Port Activity LEDs Possible Cause Corrective Action State Troubleshooting Using the Port Status LEDs Troubleshooting Using the Port Status LEDsLED State Indication Possible Cause Corrective Action Replace remote device RFS Troubleshooting Technical Assistance ONline Ethernet 10BASE-FL Installation and Operation Guide Specifications General Specifications Table A-1. General Specifications Optical Specifications Transmitter SpecificationsTable A-2. Transmit Power Peak Values Receiver Specifications Table A-3. Receiver SpecificationsSupported Fiber Optic Cables Table A-5. Power Requirements Power RequirementsTable A-4. Fiber Optic Interface Specifications Fiber Optic Interface Table A-6. Electrical Specifications Environmental SpecificationsMechanical Specifications Table A-7. Mechanical Specifications 10BASE-FL Cable and Connector Specifications Fiber Cables and Connectors Table A-8. Connector Type Part Number Connector Type Part Number Technical Support On-line Technical Support Support from Your Network Supplier Email Technical SupportWorld Wide Web Site Support from 3Com Accessing the 3Com MIB Returning Products for Repair 3Com Technical Publications Page Index Index RFS VDE compliance Verify LED Operation, 3-19Network Assignment