D. Displayand Codes, Clcc, Fill, Fls | ADC AD-26, WDA-540, AD-295

SECTION II

L.E.D. DISPLAYAND CODES

A	Automatic Cycle (Slope Program Factor)
ACOn	Accumulative Coin
Adrt	MaximumAuto Dryness Time
AFAt	Amount forAdditional Time
AGt	ActiveAnti-Wrinkle Guard Time
AtIn	AccumulativeTime
AtSt	Amount To Start
AUtO	Automatic Mode (Patent No. 4,827,627)
b	Automatic Cycle (Heat Loss [offset] Factor)
bCLO	Bad Coin Lockout
bCrS	Bad Coin Reset
bUZ	Buzzer (Tone)
oCEL	Degree in Celsius
CLCC	Clear Left Coin Count
Coin	Coin Mode
CrCC	Clear Right Coin Count
donE	Drying and Cooling Cycles Complete
	or
door	Dryer is inAnti-Wrinkle Cycle
door	Door Circuit is Open*
dSFL	Dryer Sensor Circuit Failure*
oFAr	Degree in Fahrenheit
FILL	No Cycle in Progress
FLS	Flash DisplayActive
FrEE	Free Dry Mode
GdLY	Anti-Wrinkle DelayTime
Gont	Anti-Wrinkle OnTime

*Refer to Phase 5 Coin System Diagnostics in Section VIII of this manual for detailed information.

(Continued on Next Page)

8

Image 10

ADC AD-26, WDA-540, AD-295, AD-540 user manual D. Displayand Codes, Clcc, Fill, Fls

Contents

Phase Coin USER’S Manual Retain This Manual In a Safe Place For Future Reference Important Note to Purchaser Table Of Contents Programming Instructions For all dryer models except AD-26/AD-295 and AD-540/WDA-540 Motor Circuit IndicatorFor dryer models AD-26/AD-295 Only Introduction Time for Amount to Start Cool Down Time Cool Down TemperaturesFree DRY Mode ANTI-WRINKLE Batterybackup Optional Temperature DisplayDiagnostics Automatic Drytime Fill D. Displayand CodesClcc FLS PPF LCCPloc Push Timed Mode Operating Instructions Automatic Mode Patent no ,827,627 Free DRY Mode Program Selection Temperature Display ModeRight Coin Count rCC/LEFT Coin Count LCC Automatic Review of Program Location Automatic Mode AUtO Patent No ,827,627 PL01 Temperature Conversion StatusTimed Mode tInE ANTI-WRINKLE Program Grd Free DRY Mode FrEEBUZZ/TONE bUZ Flash Display Status FLS Coin Mode CoinBAD Coin Reset bCrS BAD Coin Lockout Status bCLO Single Coin Accumulative Time AtInDual Coin PL10 rCdE PL11 tFAS PL12 AtSt Single Coin Acceptor Accumulative Coin ACOnDual Coinacceptor Rotational Safe Guard OPTIONALnSEn PL03 High Temperature HIFPL02 Percent DRY PdrY PL05 LOW Temperature LOF PL07 Permanent Press PPF PL12 Amount to Start AtSt PL10 Right Coin Slot Denomination rCdEPL11 Time for Amount to Start tFAS PL13 Minimum Amount for Additional Time AFAt PL16 Active Guard Time AGt PL15 ANTI-WRINKLE TimingPL17 a and b Factors Programming Instructions Introduction to Programming Programming Flowcharts Dryer Off Power On Display Reads No cycle in progress Button Example And/or Programming Temperature Display ModeCycle In Progress Left Coin Count Right Coin Count Program Location 01 PL01 Press Perm Press key, otherwise Display will read anti-wrinkleGuard program status. If no change Press HI or LO keys and then FLS AtIn LO Temp Continue HI Temp PL02 Perm Press Pdry Program Location 02 PL02Perm Press PL03 Program Location 03 PL03 HIF Program Location 04 PL04 HI Temp cool down temperature/timeTime Decrease Time Increase Program Location 05 PL05 Program Location 06 PL06 LO Temp cool down temperature/timeTime Decrease Program Location 07 PL07 PPF Perm Press Cool Down Temperature/Time Program Location 08 PL08 Program Location 09 PL09 PL09 Perm Press LCdE Program Location 10 PL10 Right Coin Denomination Program Location 11 PL11 Program Location 12 PL12 Proceed to next location To be changed PL12 Perm Press AtSt Program Location 13 PL13 Proceed to next location To be changed PL13 Perm Press AFAt Program Location 14 PL14 Maximum Time for Auto Dry Program Location 15 PL15 Anti-Wrinkle Timing Programmable 1 to Factor Decrease Program Location 16 PL16 and Program Location 17 PL17Maximum Active Anti-Wrinkle Time Factor Increase Factory Preset PROGRAMS/PARAMETERS Single Coin only TFAS Time for amount to start 10 minutes Dual Coin onlyLCdE Left coin denomination 10¢ AFAt Amount for additional time 10¢ PPCd Temperature 80, Time 3 minutes HICd Temperature 80, Time 2 minutesLOCd Temperature 80, Time 2 minutes NSEn Rotational sensor not selected PdrY Percent Dry 98% PL08 PPCd Temperature 80, Time 3 minutes PL06 LOCd Temperature 80, Time 2 minutesRCdE Right coin denomination 10¢ Phase 5 Coin System Diagnostics Diagnostic L.E.D. Failure Codes E.D. Display INDICATORS/DOTS Page Page Phase 5 Auto Cycle Patent no ,827,627 For 60 Hz models only For 50 Hz models only Optional 9 Volt Battery Backup Page ADC Part No 56 10/28/08