Factory Preset PROGRAMS/PARAMETERS | ADC AD-295, WDA-540, AD-26

SECTION VII

FACTORY PRESET

PROGRAMS/PARAMETERS

Unless otherwise specified at the time of ordering, the Phase 5 microprocessor controller (computer) has been preprogrammed by the factory with the following programs/parameters. Should changes be found necessary, please read this Phase 5 Coin User’s Manual carefully to thoroughly familiarize yourself with the Phase 5 microprocessor controller’s (computer’s) programming characteristics.

51

Image 53

ADC AD-295, WDA-540, AD-26, AD-540 user manual Factory Preset PROGRAMS/PARAMETERS

Contents

Phase Coin USER’S Manual Important Note to Purchaser Retain This Manual In a Safe Place For Future Reference Table Of Contents Programming Instructions For dryer models AD-26/AD-295 Only Motor Circuit IndicatorFor all dryer models except AD-26/AD-295 and AD-540/WDA-540 Introduction Time for Amount to Start Free DRY Mode Cool Down TemperaturesCool Down Time ANTI-WRINKLE Diagnostics Temperature DisplayBatterybackup Optional Automatic Drytime Clcc D. Displayand CodesFill FLS Ploc LCCPPF Push Operating Instructions Timed Mode Automatic Mode Patent no ,827,627 Free DRY Mode Right Coin Count rCC/LEFT Coin Count LCC Temperature Display ModeProgram Selection Automatic Review of Program Location Timed Mode tInE PL01 Temperature Conversion StatusAutomatic Mode AUtO Patent No ,827,627 BUZZ/TONE bUZ Free DRY Mode FrEEANTI-WRINKLE Program Grd BAD Coin Reset bCrS Coin Mode CoinFlash Display Status FLS BAD Coin Lockout Status bCLO Dual Coin Accumulative Time AtInSingle Coin PL10 rCdE PL11 tFAS PL12 AtSt Dual Coinacceptor Accumulative Coin ACOnSingle Coin Acceptor PL02 Percent DRY PdrY PL03 High Temperature HIFRotational Safe Guard OPTIONALnSEn PL07 Permanent Press PPF PL05 LOW Temperature LOF PL11 Time for Amount to Start tFAS PL10 Right Coin Slot Denomination rCdEPL12 Amount to Start AtSt PL13 Minimum Amount for Additional Time AFAt PL17 a and b Factors PL15 ANTI-WRINKLE TimingPL16 Active Guard Time AGt Introduction to Programming Programming Instructions Programming Flowcharts Button Dryer Off Power On Display Reads No cycle in progress And/or Example Cycle In Progress Temperature Display ModeProgramming Left Coin Count Right Coin Count Program Location 01 PL01 Guard program status. If no change Display will read anti-wrinklePress Perm Press key, otherwise Press HI or LO keys and then FLS AtIn LO Temp Continue HI Temp Perm Press PL03 Program Location 02 PL02PL02 Perm Press Pdry HIF Program Location 03 PL03 Time Decrease Time Increase HI Temp cool down temperature/timeProgram Location 04 PL04 Program Location 05 PL05 Time Decrease LO Temp cool down temperature/timeProgram Location 06 PL06 PPF Program Location 07 PL07 Program Location 08 PL08 Perm Press Cool Down Temperature/Time PL09 Perm Press LCdE Program Location 09 PL09 Right Coin Denomination Program Location 10 PL10 Program Location 11 PL11 Proceed to next location To be changed PL12 Perm Press AtSt Program Location 12 PL12 Proceed to next location To be changed PL13 Perm Press AFAt Program Location 13 PL13 Maximum Time for Auto Dry Program Location 14 PL14 Anti-Wrinkle Timing Program Location 15 PL15 Maximum Active Anti-Wrinkle Time Program Location 16 PL16 and Program Location 17 PL17Programmable 1 to Factor Decrease Factor Increase Factory Preset PROGRAMS/PARAMETERS Single Coin only LCdE Left coin denomination 10¢ Dual Coin onlyTFAS Time for amount to start 10 minutes AFAt Amount for additional time 10¢ LOCd Temperature 80, Time 2 minutes HICd Temperature 80, Time 2 minutesPPCd Temperature 80, Time 3 minutes NSEn Rotational sensor not selected PdrY Percent Dry 98% RCdE Right coin denomination 10¢ PL06 LOCd Temperature 80, Time 2 minutesPL08 PPCd Temperature 80, Time 3 minutes Diagnostic L.E.D. Failure Codes Phase 5 Coin System Diagnostics E.D. Display INDICATORS/DOTS Page Page Phase 5 Auto Cycle Patent no ,827,627 For 60 Hz models only For 50 Hz models only Optional 9 Volt Battery Backup Page ADC Part No 56 10/28/08