HICd Temperature 80, Time 2 minutes, 130 | ADC WDA-540, AD-295

C. SINGLE COIN ONLY

For dryer models AD-26/AD-295 and AD-540/WDA-540 ONLY

PL01 -	°FAr	- Temperatures in Fahrenheit
	tInE	- Timed mode
	Grd	- Anti-wrinkle guard on
	bUZ	- Anti-wrinkle guard buzzer (tone) on
	Coin	- Coin(s) required to start
	FLS	- Display will flash in intervals between “FILL” and “Amount To Start”
	bCrS	- Bad coin reset
	AtIn	- Accumulative time
PL02 -	nSEn	- Rotational sensor not selected
PL02 -	PdrY	- Percent Dry - 98%
PL03 -	HIOF	- 150°
PL04 -	HICd	- Temperature - 80°, Time - 2 minutes
PL05 -	LO°F	- 120°
PL06 -	LOCd	- Temperature - 80°, Time - 2 minutes
PL07 -	PP°F	- 130°
PL08 -	PPCd	- Temperature - 80°, Time - 3 minutes
PL09 -	LCdE	- Left coin denomination - 25¢
PL10 - rCdE		- Right coin denomination - 10¢
PL11 -	tFAS	- Time for amount to start - 10 minutes
PL12 -	AtSt	- Amount to Start - 25¢
PL13 -	AFAt	- Amount for additional time - 25¢
PL14 -	Adrt	- Automatic dry maximum time - 30 minutes
PL15 -	GdLY	- Anti-wrinkle guard off delay time - 2 minutes
PL16 -	Gont	- Anti-wrinkle guard on time - 20-seconds
PL16 -	AGt	- Active anti-wrinkle guard time - 10 minutes
PL17 -	A and b	- “A” is adjustable from 1 to 99 (example: A = 5)
	Factors	- “b” is adjustable from 1 to 99 (example: B = 70)

54

Image 56

ADC WDA-540, AD-295 NSEn Rotational sensor not selected PdrY Percent Dry 98%, HICd Temperature 80, Time 2 minutes, 130

Contents

Phase Coin USER’S Manual Retain This Manual In a Safe Place For Future Reference Important Note to Purchaser Table Of Contents Programming Instructions For dryer models AD-26/AD-295 Only Motor Circuit IndicatorFor all dryer models except AD-26/AD-295 and AD-540/WDA-540 Introduction Time for Amount to Start Cool Down Temperatures Free DRY ModeCool Down Time ANTI-WRINKLE Temperature Display DiagnosticsBatterybackup Optional Automatic Drytime D. Displayand Codes ClccFill FLS LCC PlocPPF Push Timed Mode Operating Instructions Automatic Mode Patent no ,827,627 Free DRY Mode Right Coin Count rCC/LEFT Coin Count LCC Temperature Display ModeProgram Selection Automatic Review of Program Location Timed Mode tInE PL01 Temperature Conversion StatusAutomatic Mode AUtO Patent No ,827,627 BUZZ/TONE bUZ Free DRY Mode FrEEANTI-WRINKLE Program Grd Coin Mode Coin BAD Coin Reset bCrSFlash Display Status FLS BAD Coin Lockout Status bCLO Dual Coin Accumulative Time AtInSingle Coin PL10 rCdE PL11 tFAS PL12 AtSt Dual Coinacceptor Accumulative Coin ACOnSingle Coin Acceptor PL02 Percent DRY PdrY PL03 High Temperature HIFRotational Safe Guard OPTIONALnSEn PL05 LOW Temperature LOF PL07 Permanent Press PPF PL10 Right Coin Slot Denomination rCdE PL11 Time for Amount to Start tFASPL12 Amount to Start AtSt PL13 Minimum Amount for Additional Time AFAt PL17 a and b Factors PL15 ANTI-WRINKLE TimingPL16 Active Guard Time AGt Programming Instructions Introduction to Programming Programming Flowcharts Dryer Off Power On Display Reads No cycle in progress Button Example And/or Cycle In Progress Temperature Display ModeProgramming Left Coin Count Right Coin Count Program Location 01 PL01 Display will read anti-wrinkle Guard program status. If no changePress Perm Press key, otherwise Press HI or LO keys and then FLS AtIn LO Temp Continue HI Temp Perm Press PL03 Program Location 02 PL02PL02 Perm Press Pdry Program Location 03 PL03 HIF Time Decrease Time Increase HI Temp cool down temperature/timeProgram Location 04 PL04 Program Location 05 PL05 Time Decrease LO Temp cool down temperature/timeProgram Location 06 PL06 Program Location 07 PL07 PPF Perm Press Cool Down Temperature/Time Program Location 08 PL08 Program Location 09 PL09 PL09 Perm Press LCdE Program Location 10 PL10 Right Coin Denomination Program Location 11 PL11 Program Location 12 PL12 Proceed to next location To be changed PL12 Perm Press AtSt Program Location 13 PL13 Proceed to next location To be changed PL13 Perm Press AFAt Program Location 14 PL14 Maximum Time for Auto Dry Program Location 15 PL15 Anti-Wrinkle Timing Program Location 16 PL16 and Program Location 17 PL17 Maximum Active Anti-Wrinkle TimeProgrammable 1 to Factor Decrease Factor Increase Factory Preset PROGRAMS/PARAMETERS Single Coin only Dual Coin only LCdE Left coin denomination 10¢TFAS Time for amount to start 10 minutes AFAt Amount for additional time 10¢ HICd Temperature 80, Time 2 minutes LOCd Temperature 80, Time 2 minutesPPCd Temperature 80, Time 3 minutes NSEn Rotational sensor not selected PdrY Percent Dry 98% RCdE Right coin denomination 10¢ PL06 LOCd Temperature 80, Time 2 minutesPL08 PPCd Temperature 80, Time 3 minutes Phase 5 Coin System Diagnostics Diagnostic L.E.D. Failure Codes E.D. Display INDICATORS/DOTS Page Page Phase 5 Auto Cycle Patent no ,827,627 For 60 Hz models only For 50 Hz models only Optional 9 Volt Battery Backup Page ADC Part No 56 10/28/08