Programming, Temperature Display Mode | ADC AD-540, WDA-540, AD-295

SECTION VI

PROGRAMMING

A. TEMPERATURE DISPLAY MODE

							25
	FILL			and/or
	FILL			and/or

(Close Program Switch)

75F

Cycle In Progress

HI°2°0

(Close Program Switch)

13°5°F

(Open Basket [Tumbler] Door-Dryer Shuts Off)

135F

(Close Door - Open Program Switch)

(Amount To Start)

(Dryer Temperature Display)

(Temperature Selection/Time)

(Dryer Temperature Display)

HI Temp

LO Temp

Perm Press

LO°2°0

29

Image 31

ADC AD-540, WDA-540, AD-295, AD-26 user manual Programming, Temperature Display Mode, Cycle In Progress

Contents

Phase Coin USER’S Manual Important Note to Purchaser Retain This Manual In a Safe Place For Future Reference Table Of Contents Programming Instructions For all dryer models except AD-26/AD-295 and AD-540/WDA-540 Motor Circuit IndicatorFor dryer models AD-26/AD-295 Only Introduction Time for Amount to Start ANTI-WRINKLE Cool Down TemperaturesFree DRY Mode Cool Down Time Automatic Drytime Temperature DisplayDiagnostics Batterybackup Optional FLS D. Displayand CodesClcc Fill Push LCCPloc PPF Operating Instructions Timed Mode Automatic Mode Patent no ,827,627 Free DRY Mode Program Selection Temperature Display ModeRight Coin Count rCC/LEFT Coin Count LCC Automatic Review of Program Location Automatic Mode AUtO Patent No ,827,627 PL01 Temperature Conversion StatusTimed Mode tInE ANTI-WRINKLE Program Grd Free DRY Mode FrEEBUZZ/TONE bUZ BAD Coin Lockout Status bCLO Coin Mode CoinBAD Coin Reset bCrS Flash Display Status FLS Single Coin Accumulative Time AtInDual Coin PL10 rCdE PL11 tFAS PL12 AtSt Single Coin Acceptor Accumulative Coin ACOnDual Coinacceptor Rotational Safe Guard OPTIONALnSEn PL03 High Temperature HIFPL02 Percent DRY PdrY PL07 Permanent Press PPF PL05 LOW Temperature LOF PL13 Minimum Amount for Additional Time AFAt PL10 Right Coin Slot Denomination rCdEPL11 Time for Amount to Start tFAS PL12 Amount to Start AtSt PL16 Active Guard Time AGt PL15 ANTI-WRINKLE TimingPL17 a and b Factors Introduction to Programming Programming Instructions Programming Flowcharts Button Dryer Off Power On Display Reads No cycle in progress And/or Example Programming Temperature Display ModeCycle In Progress Left Coin Count Right Coin Count Program Location 01 PL01 Press HI or LO keys and then Display will read anti-wrinkleGuard program status. If no change Press Perm Press key, otherwise FLS AtIn LO Temp Continue HI Temp PL02 Perm Press Pdry Program Location 02 PL02Perm Press PL03 HIF Program Location 03 PL03 Program Location 04 PL04 HI Temp cool down temperature/timeTime Decrease Time Increase Program Location 05 PL05 Program Location 06 PL06 LO Temp cool down temperature/timeTime Decrease PPF Program Location 07 PL07 Program Location 08 PL08 Perm Press Cool Down Temperature/Time PL09 Perm Press LCdE Program Location 09 PL09 Right Coin Denomination Program Location 10 PL10 Program Location 11 PL11 Proceed to next location To be changed PL12 Perm Press AtSt Program Location 12 PL12 Proceed to next location To be changed PL13 Perm Press AFAt Program Location 13 PL13 Maximum Time for Auto Dry Program Location 14 PL14 Anti-Wrinkle Timing Program Location 15 PL15 Factor Increase Program Location 16 PL16 and Program Location 17 PL17Maximum Active Anti-Wrinkle Time Programmable 1 to Factor Decrease Factory Preset PROGRAMS/PARAMETERS Single Coin only AFAt Amount for additional time 10¢ Dual Coin onlyLCdE Left coin denomination 10¢ TFAS Time for amount to start 10 minutes NSEn Rotational sensor not selected PdrY Percent Dry 98% HICd Temperature 80, Time 2 minutesLOCd Temperature 80, Time 2 minutes PPCd Temperature 80, Time 3 minutes PL08 PPCd Temperature 80, Time 3 minutes PL06 LOCd Temperature 80, Time 2 minutesRCdE Right coin denomination 10¢ Diagnostic L.E.D. Failure Codes Phase 5 Coin System Diagnostics E.D. Display INDICATORS/DOTS Page Page Phase 5 Auto Cycle Patent no ,827,627 For 60 Hz models only For 50 Hz models only Optional 9 Volt Battery Backup Page ADC Part No 56 10/28/08