E.D. Display INDICATORS/DOTS | ADC AD-540, WDA-540, AD-295, AD-26

3.“SEFL” - Indicates rotational sensor circuit failure meaning that there is a fault somewhere in the basket (tumbler) rotation detection circuit or the microprocessor controller (computer) program related to this circuit (PL01) is set incorrectly in the active mode (“SEn”), where the dryer is not equipped with optional rotation sensor and should be set in the inactive mode (“nSEn”).

4.“Hot” - Indicates a possible overheating condition. The Phase 5 microprocessor controller (computer) monitors the temperature in the dryer at ALL times. If the microprocessor controller (computer) detects that the temperature in the dryer has exceeded 220° F (104° C) it will disable ALL outputs (shut the dryer down), the tone (buzzer) will sound for approximately 5-seconds, and the display will read “Hot.” The light emitting diode (L.E.D.) display will continue to read “Hot” until the temperature sensed has dropped to 220° F (104° C) or lower and the microprocessor controller (computer) is manually reset by closing and opening the Program Switch (PS).

B.L.E.D. DISPLAY INDICATORS/DOTS

The L.E.D. indicator dots located at the top portion of the display indicates the various microprocessor controller (computer) output functions while a cycle is in progress. These dots DO NOT necessarily mean that the outputs are functioning. They are only indicating that the function (output) should be active (on).

1.Heat Circuit Indicator - indicator dot is on whenever the microprocessor controller (computer) is calling for the heating circuit to be active (on).

2.Motor Circuit Indicator - indicator dot is on whenever a cycle is in progress.

57

Image 59

ADC AD-540, WDA-540, AD-295, AD-26 user manual E.D. Display INDICATORS/DOTS

Contents

Phase Coin USER’S Manual Important Note to Purchaser Retain This Manual In a Safe Place For Future Reference Table Of Contents Programming Instructions For dryer models AD-26/AD-295 Only Motor Circuit IndicatorFor all dryer models except AD-26/AD-295 and AD-540/WDA-540 Introduction Time for Amount to Start ANTI-WRINKLE Cool Down TemperaturesFree DRY Mode Cool Down Time Automatic Drytime Temperature DisplayDiagnostics Batterybackup Optional FLS D. Displayand CodesClcc Fill Push LCCPloc PPF Operating Instructions Timed Mode Automatic Mode Patent no ,827,627 Free DRY Mode Right Coin Count rCC/LEFT Coin Count LCC Temperature Display ModeProgram Selection Automatic Review of Program Location Timed Mode tInE PL01 Temperature Conversion StatusAutomatic Mode AUtO Patent No ,827,627 BUZZ/TONE bUZ Free DRY Mode FrEEANTI-WRINKLE Program Grd BAD Coin Lockout Status bCLO Coin Mode CoinBAD Coin Reset bCrS Flash Display Status FLS Dual Coin Accumulative Time AtInSingle Coin PL10 rCdE PL11 tFAS PL12 AtSt Dual Coinacceptor Accumulative Coin ACOnSingle Coin Acceptor PL02 Percent DRY PdrY PL03 High Temperature HIFRotational Safe Guard OPTIONALnSEn PL07 Permanent Press PPF PL05 LOW Temperature LOF PL13 Minimum Amount for Additional Time AFAt PL10 Right Coin Slot Denomination rCdEPL11 Time for Amount to Start tFAS PL12 Amount to Start AtSt PL17 a and b Factors PL15 ANTI-WRINKLE TimingPL16 Active Guard Time AGt Introduction to Programming Programming Instructions Programming Flowcharts Button Dryer Off Power On Display Reads No cycle in progress And/or Example Cycle In Progress Temperature Display ModeProgramming Left Coin Count Right Coin Count Program Location 01 PL01 Press HI or LO keys and then Display will read anti-wrinkleGuard program status. If no change Press Perm Press key, otherwise FLS AtIn LO Temp Continue HI Temp Perm Press PL03 Program Location 02 PL02PL02 Perm Press Pdry HIF Program Location 03 PL03 Time Decrease Time Increase HI Temp cool down temperature/timeProgram Location 04 PL04 Program Location 05 PL05 Time Decrease LO Temp cool down temperature/timeProgram Location 06 PL06 PPF Program Location 07 PL07 Program Location 08 PL08 Perm Press Cool Down Temperature/Time PL09 Perm Press LCdE Program Location 09 PL09 Right Coin Denomination Program Location 10 PL10 Program Location 11 PL11 Proceed to next location To be changed PL12 Perm Press AtSt Program Location 12 PL12 Proceed to next location To be changed PL13 Perm Press AFAt Program Location 13 PL13 Maximum Time for Auto Dry Program Location 14 PL14 Anti-Wrinkle Timing Program Location 15 PL15 Factor Increase Program Location 16 PL16 and Program Location 17 PL17Maximum Active Anti-Wrinkle Time Programmable 1 to Factor Decrease Factory Preset PROGRAMS/PARAMETERS Single Coin only AFAt Amount for additional time 10¢ Dual Coin onlyLCdE Left coin denomination 10¢ TFAS Time for amount to start 10 minutes NSEn Rotational sensor not selected PdrY Percent Dry 98% HICd Temperature 80, Time 2 minutesLOCd Temperature 80, Time 2 minutes PPCd Temperature 80, Time 3 minutes RCdE Right coin denomination 10¢ PL06 LOCd Temperature 80, Time 2 minutesPL08 PPCd Temperature 80, Time 3 minutes Diagnostic L.E.D. Failure Codes Phase 5 Coin System Diagnostics E.D. Display INDICATORS/DOTS Page Page Phase 5 Auto Cycle Patent no ,827,627 For 60 Hz models only For 50 Hz models only Optional 9 Volt Battery Backup Page ADC Part No 56 10/28/08