Lcc, Ploc, Ppf, Push, Sefl | ADC AD-540, WDA-540, AD-295, AD-26

Grd	Anti-Wrinkle ProgramActive
HICd	High Cool Down
Hot	Overheating Condition*
LCC	Left Coin Count
LCdE	Left Coin Denomination
LOCd	Low Cool Down
nbUZ	No Buzzer (Tone)
nFLS	No Flash Display
nGrd	NoAnti-Wrinkle
nSEn	No Rotational Sensor Selected
PdrY	Percent Dry
PL	Program Location
PLOC	Program LocationAutomation Review
PPCd	Permanent Press Cool Down
PP°F	Permanent Press
PUSH	Amount To Start Has Been Inserted
rCC	Make Temperature Selection
rCC	Right Coin Count
rCdE	Right Coin Denomination
SEFL	Rotational Sensor Circuit Failure*
SEn	Rotational Sensor Selected
tFAS	Time ForAmount To Start
tInE	Timed Mode

* Refer to Phase 5 Coin System Diagnostics in Section VIII of this manual for detailed information.

9

Image 11

ADC AD-540, WDA-540, AD-295, AD-26 user manual Lcc, Ploc, Ppf, Push, Sefl

Contents

Phase Coin USER’S Manual Important Note to Purchaser Retain This Manual In a Safe Place For Future Reference Table Of Contents Programming Instructions For dryer models AD-26/AD-295 Only Motor Circuit IndicatorFor all dryer models except AD-26/AD-295 and AD-540/WDA-540 Introduction Time for Amount to Start ANTI-WRINKLE Cool Down TemperaturesFree DRY Mode Cool Down Time Automatic Drytime Temperature DisplayDiagnostics Batterybackup Optional FLS D. Displayand CodesClcc Fill Push LCCPloc PPF Operating Instructions Timed Mode Automatic Mode Patent no ,827,627 Free DRY Mode Right Coin Count rCC/LEFT Coin Count LCC Temperature Display ModeProgram Selection Automatic Review of Program Location Timed Mode tInE PL01 Temperature Conversion StatusAutomatic Mode AUtO Patent No ,827,627 BUZZ/TONE bUZ Free DRY Mode FrEEANTI-WRINKLE Program Grd BAD Coin Lockout Status bCLO Coin Mode CoinBAD Coin Reset bCrS Flash Display Status FLS Dual Coin Accumulative Time AtInSingle Coin PL10 rCdE PL11 tFAS PL12 AtSt Dual Coinacceptor Accumulative Coin ACOnSingle Coin Acceptor PL02 Percent DRY PdrY PL03 High Temperature HIFRotational Safe Guard OPTIONALnSEn PL07 Permanent Press PPF PL05 LOW Temperature LOF PL13 Minimum Amount for Additional Time AFAt PL10 Right Coin Slot Denomination rCdEPL11 Time for Amount to Start tFAS PL12 Amount to Start AtSt PL17 a and b Factors PL15 ANTI-WRINKLE TimingPL16 Active Guard Time AGt Introduction to Programming Programming Instructions Programming Flowcharts Button Dryer Off Power On Display Reads No cycle in progress And/or Example Cycle In Progress Temperature Display ModeProgramming Left Coin Count Right Coin Count Program Location 01 PL01 Press HI or LO keys and then Display will read anti-wrinkleGuard program status. If no change Press Perm Press key, otherwise FLS AtIn LO Temp Continue HI Temp Perm Press PL03 Program Location 02 PL02PL02 Perm Press Pdry HIF Program Location 03 PL03 Time Decrease Time Increase HI Temp cool down temperature/timeProgram Location 04 PL04 Program Location 05 PL05 Time Decrease LO Temp cool down temperature/timeProgram Location 06 PL06 PPF Program Location 07 PL07 Program Location 08 PL08 Perm Press Cool Down Temperature/Time PL09 Perm Press LCdE Program Location 09 PL09 Right Coin Denomination Program Location 10 PL10 Program Location 11 PL11 Proceed to next location To be changed PL12 Perm Press AtSt Program Location 12 PL12 Proceed to next location To be changed PL13 Perm Press AFAt Program Location 13 PL13 Maximum Time for Auto Dry Program Location 14 PL14 Anti-Wrinkle Timing Program Location 15 PL15 Factor Increase Program Location 16 PL16 and Program Location 17 PL17Maximum Active Anti-Wrinkle Time Programmable 1 to Factor Decrease Factory Preset PROGRAMS/PARAMETERS Single Coin only AFAt Amount for additional time 10¢ Dual Coin onlyLCdE Left coin denomination 10¢ TFAS Time for amount to start 10 minutes NSEn Rotational sensor not selected PdrY Percent Dry 98% HICd Temperature 80, Time 2 minutesLOCd Temperature 80, Time 2 minutes PPCd Temperature 80, Time 3 minutes RCdE Right coin denomination 10¢ PL06 LOCd Temperature 80, Time 2 minutesPL08 PPCd Temperature 80, Time 3 minutes Diagnostic L.E.D. Failure Codes Phase 5 Coin System Diagnostics E.D. Display INDICATORS/DOTS Page Page Phase 5 Auto Cycle Patent no ,827,627 For 60 Hz models only For 50 Hz models only Optional 9 Volt Battery Backup Page ADC Part No 56 10/28/08