SOURce TELecom OFFSet?, SOURce JITTer RANGe range | Anritsu MP1777A

Section 8 Device Message Details

:SOURce :TELecom : OFFSet <numeric>

Command type

Parameter

Function Example of use

Sequential command

<numeric> = <DECIMAL NUMERIC PROGRAM DATA> -50 to +50 ... step 0.I

Performs the frequency offset setting.

Sets the value of frequency offset at +25.

>: SOURce : TELecom : OFFSet 25

:SOURce : TELecom :OFFSet?

Command type	Sequential command
Response	<NR 1 NUMERIC RESPONSE DATA>
	-50 to +50 ... step 0.1
Function	Makes a query of the value of frequency offset.
Example of use	> : SOURce : TELecorn : OFFSet?

<-25

:SOURce : JITTer : RANGe <range>

Command type	Sequential command
Parameter	<range> = C H A R A C T E R PROGRAM DATA>
	UI3200	3,200 UIPP
	UI1600	1,600 UIPP
	UI800	800 UIPP
	U180	8 0 UIPP
	U140	40 UIPP
	UI20	20 UIPP
	UI05	0.5 UIPP
Function	Performs setting of the transmission jitter generation range.
Restriction	Effective when transmission jitter is generated.
	Restrictions on setting apply depending on the Bit Rate.

Bit Rate	UI Range
10 G	3.200. 80, 0.5 UI

Example of use	Sets the transmission jitter generation range at 0.5 UIPP.
	> : SOURce : JITTer : RAN& UI05

Image 88

Anritsu MP1777A Device Message Details SOURce TELecom OFFSet numeric, SOURce TELecom OFFSet?, SOURce JITTer RANGe range

Contents

Keep this manual with the equipment Document No. M-W1493AE-4.0 Safety Symbols Repair Falling Over Battery Fluid This liquid is very caustic and poisonous For Safety Changing Fuse Cleaning Changing memory back-up batteryPage Anritsu Corporation Contact Trademark and Registered Trademark VOL Table of Contents Status Report Device Message DetailsPage Outline Interface Function System Setup Example Control from a host computer Outline GPlB Interface Gpib lnterface Functions Gpib lnterfaceGpib lnterface Functions Interface Function IEEE488.2 Standards Device Message List Device Message ListFi6 -1Device Message I0 Buffer Bus Commands Details of Bus CommandsBus Command Operations Gpib Interface Connecting the Gpib Ca 2Sketch of GPlB Cabi2 Setting GPlB Jitter Setting EqualizerGPlB Interface T u ~ I Interface 1 ITx&Rxl Time XX XX XX Xwxxwxx Bit Rate Setup 5Secondary System Screen When GPlB Interface is Used Initializing the Device Types of System lnitializationOutline Level Type of Initialization Initializing the Device Gpib Interface Ection 3 Listener Input Format Listener lnput Format Write @03 Sens TEL Rang U14 Sens TEL Brat M9953 eNL TalkerController Sens TEL Brat ~9953 Listener Input Program Message Format Write @ Listener Input Format Functional Elements of Program MessageRefer to Program Message Terminator Functional Elements of Program Message Sens TEL Rang U14 Sens TEL Brat M9953 Program Message Unit Separator Command Message Unit and Query Message Unit Syst Date 1993,7,15 Data Separator Common command \--Iprogram headers- I Refer to 2 Short form Long form mnemonicProgram mnemonic Refer to 3 Upper/lower case alpha Upper/lower 1 case aloha Command Program Header Query Program Header 1 1 Program Data Separator Program Data Format Program Data Format Decimal Numeric Program Data Integer type Boolean Program Data Listener Input Format Ection 4 Talker Output Format Listener Talker Output Response Message FormatDevice Functional Elements of Response Message Functional Elements of Response MessageM9953 cNL Response Message UNlT Separator Response Message Unit Response Data Common1 EE488.2 Commands Common IEEE488.2 Commands List of Common IEEE488.2 CommandsCommon IEEE488.2 Description Operation Complete Command Wait Continue CommandIdentification Query Operation Complete Query Standard Event Status Enable Command Clear Status CommandStandard Event Status Register Query Service Request Enable Query SSRE Service Request Enable CommandRead Status Byte Query Power On Status Clear Command Section Common IEEE488.2 CommandsPower On Status C l e a r Query Recall Command Common IEEE488.2Option Identification Query ~ t i o n Common IEEE488.2 Commands ElementFunction Quote char Data byte Common IEEE488.2 Commands Status Report 1Block Diagram of Status Registers Status Report Register and Filter Configuration of MP1777A Status RegistersSummary Message Status Registers Specified by IEEE488.2 Definitions of Status Registers Specified by IEEE488.2Definition Logical or Definition of Status Byte Register Bit Bit Status Byte Register DefinitionDefinition of Standard Event Status Register Bit Bit Standard Event Status Register Definition To the status Byte register Bit Status Register Specified by ScpiDefinition Status Register Specific to MP1777A Status Register Specific to MP1777AINSTrument Status register To the OPERation Reading and writing methods Reading, Writing and Clearing Status RegistersWriting Methods Reset Value Clearing and Resetting Methods of Status RegistersReaister Status Report Scpi Outline Outline Scpi Outline Command Structure Example of Scpi Command TreeSOURce TELecom BRATe Brate BRATe? EQUAlizer EQUAlizer? Command Description Method CommandformatSCPl Outline Form of header abbreviation Compounding Commands Scpi Outline Details of Parameter Type Parameter T V D ~ Device Message Details INSTrument Subsystem Response Format Device Message DetailsResponse Format By Response Type Format Response Format Details of Response Format Buffer Size Stipulations Program command Device Message Details Program Query Command U14 Device-Specific Commands INSTrument COUPle modeCOUPle ALL ............. Tx&Rx Same SOURce Subsystem M5156 M6138SOURce TELecom BRATe? SOURce TELecom EQUAlizer? Device Message Details SOURce TELecom EQUAlizer booleanSOURce TELecom CLOCk SOURce csource SOURce TELecom JlTTer boolean Device-Specific Commands SOURce TELecom CLOCk SOURce?SOURce TELecom JITTer? Device Message Details SOURce TELecom OFFSet numeric SOURce TELecom OFFSet?SOURce JITTer RANGe range UI800 SUORce JlTTer AMPLitude? Bit Rate UI Ranae SENSe Subsystem SENSe TELecom BRATe? SENSe TELecom RANGe? SENSe TELecom RANGe rangeSENSe TELecom FlLTer filter Device-Specific Commands SENSe TELecom FILTer? SENSe TELecom MEASure Type mmodeREPeat SENSe TELecom MEASure TYPE? SENSe TELecom MEASure PERiod? SENSe MEASure STARt Device-Specific Commands SENSe MEASure STATe?SENSe MEASure Stop Device Message Details SENSe MEASure STIMe? DlSPlay DSELect Name display DlSPlay DSELect NAME? DlSPlay SETup NAME? DlSPlay SETup Name sdisplayDlSPlay RESult JITTer Mode mode DlSPlay RESult JlTTer Unit unit Device-Specific Commands DlSPlay RESult JlTTer MODE?DlSPlay RESult JlTTer UNIT? CALCulate DATA? string CALCulate DATA?String Response Format Jitter manual measurement SYSTem MEMory RECall numeric SYSTem MEMory STORe numeric SYSTern MEMory LABel numeric, title Device Message Details SYSTern MEMory CLEar numericSYSTern MEMory LABel? numeric SYSTem Date numericl, numeric2, ~numeric3r SYSTem DATE?SYSTem Time numericl, numeric2, nurneric3 SYSTem TIME? SYSTern ERRor? Device Message Details SYSTern BUZZer booleanSYSTem BUZZer? SYSTern VERSion? STATus PRESet STATus OPERation EVENt? STATus OPERation ENABle? STATus OPERation ENABle numericDevice Message Details STATus OPERation CONDition? STATus OPERation PTRansition? Status OPERation NTRansition numeric STATus OPERation INSTrument EVENt? Device Message Details STATus OPERation NTRansition?STATus OPERation INSTrument CONDition? STATus OPERation INSTrument ENABle? STATus OPERation INSTrument ENABle numericStatus OPERation INSTrument PTRansition numeric STATUSOPERation INSTrument NTRansition numeric STATus OPERation INSTrument NTRansition? Appendix a Scpi Error Messages Device-Specific Errors Command Errors Messaae Error Detection Condition Code Run Time Errors Appendix a SCPl Error MessagesTable A-2 Error Messages of Run Time Errors Code Message Error Detection Condition Table A-3 Error Messages of Device-Specific Errors Device-Specific ErrorsCode Message Error Detection Condition Query Errors Table A-4Error Messages of Query Errors Code Appendix B Appendix B Details of Initialization Command Functions Initializing BusTable B-2 Changes in Status of Device by IFC Message IFC Message Changes in Status of Device Lnitializing Message Lnitializing Message Initializing Device Device Status at Power Activation Items related to the Power On Status Clear PSC flag Appendix B Details of Initialization Command Functions Head office address was changed Page Argentina BrazilCanada Chile Bulgaria CroatiaCzech Republic Denmark Cyprus EgyptIndonesia Israel South Africa PakistanThailand