Common IEEE488.2, Recall Command, ~ t i o n | Anritsu MP1777A

	5.1 Common IEEE488.2
*RCL	Recall Command
Parameter	<DECIMAL NUMERIC PROGRAM DATA>
	0 to 10
Function	Calls the memory of a specified number and, by doing so, returns the device to the previous
	state.
	There is no limit to the state to be loaded. See the Table 7-1 in the Section 7.5 "Parameter".
	As an SCPI command which has the same function, : SYSTem : MEMory : RECall is avail-
	able.
Example of use	Calls the information stored in memory number 1 and performs setting.
	> *RCL 1
*OPT?	Option Identification Query
Response	<ARBITRARY ASCII RESPONSE DATA>
	Characters to correspond to the option or unit

	O ~ t i o n	Character
	Interface (Bit Rate) selection condition option
	Standard	OPT0
	l 2,488 M, 4,977 M. 9,953 M
	Interface (Bit Rate) selection condition option
	Option 0 1	OPT 1
	l 2,494 M, 3.988 M, 9,977 M
	Interface (Bit Rate) selection condition option
	Option 02	OPT2
	l 2,666 M, 5.332 M, 10,644 M
	Interface (Bit Rate) selection condition option
	Option 04
	03,062 M, 6,125 M, 12,249 M
	Interface (Bit Rate) selection condition option
	Option 05	OPT5
	l 3,069 M. 6,138 M, 12,276 M
	Interface (Bit Rate) selection condition option
	Option 06	OPT6
	02,677 M, 5,355 M, 10.709 M
	Interface (Bit Rate) selection condition option
	Option 07	OPT7
	l 2,578 M, 5,156 M, lO,313 M
Function	Reports on the list of options and units mounted.
	Reports on options and units mounted all delimited by a comma.
Example of use	Options 01 and 02 are mounted.
	> .OPT?

< OPT1 , OPT2

Image 57

Anritsu MP1777A operation manual Common IEEE488.2, Recall Command, Option Identification Query, ~ t i o n, Character

Contents

Document No. M-W1493AE-4.0 Keep this manual with the equipment Safety Symbols Falling Over Repair This liquid is very caustic and poisonous Battery Fluid Changing Fuse Cleaning Changing memory back-up battery For SafetyPage Anritsu Corporation Contact Trademark and Registered Trademark VOL Table of Contents Device Message Details Status ReportPage Outline Interface Function Control from a host computer System Setup Example Outline GPlB Interface Gpib lnterface Gpib lnterface FunctionsGpib lnterface Functions Interface Function IEEE488.2 Standards Device Message List Device Message ListFi6 -1Device Message I0 Buffer Details of Bus Commands Bus CommandsBus Command Operations Gpib Interface 2Sketch of GPlB Cabi2 Connecting the Gpib Ca Jitter Setting Equalizer Setting GPlBGPlB Interface T u ~ I Interface 1 ITx&Rxl Time XX XX XX Xwxxwxx Bit Rate 5Secondary System Screen When GPlB Interface is Used Setup Types of System lnitialization Initializing the DeviceOutline Level Type of Initialization Initializing the Device Gpib Interface Ection 3 Listener Input Format Write @03 Sens TEL Rang U14 Sens TEL Brat M9953 eNL Talker Listener lnput FormatController Sens TEL Brat ~9953 Write @ Listener Input Program Message Format Functional Elements of Program Message Listener Input FormatRefer to Functional Elements of Program Message Program Message Terminator Sens TEL Rang U14 Sens TEL Brat M9953 Program Message Unit Separator Syst Date 1993,7,15 Command Message Unit and Query Message Unit Data Separator Short form Long form mnemonic Common command \--Iprogram headers- I Refer to 2Program mnemonic Refer to 3 Upper/lower case alpha Upper/lower 1 case aloha Command Program Header Query Program Header 1 1 Program Data Separator Program Data Format Program Data Format Integer type Decimal Numeric Program Data Boolean Program Data Listener Input Format Ection 4 Talker Output Format Talker Output Response Message Format ListenerDevice Functional Elements of Response Message Functional Elements of Response MessageM9953 cNL Response Message UNlT Separator Response Message Unit Response Data Common1 EE488.2 Commands List of Common IEEE488.2 Commands Common IEEE488.2 CommandsCommon IEEE488.2 Description Wait Continue Command Operation Complete CommandIdentification Query Operation Complete Query Clear Status Command Standard Event Status Enable CommandStandard Event Status Register Query SSRE Service Request Enable Command Service Request Enable QueryRead Status Byte Query Section Common IEEE488.2 Commands Power On Status Clear CommandPower On Status C l e a r Query Common IEEE488.2 Recall CommandOption Identification Query ~ t i o n Common IEEE488.2 Commands ElementFunction Data byte Quote char Common IEEE488.2 Commands Status Report Status Report 1Block Diagram of Status Registers Configuration of MP1777A Status Registers Register and FilterSummary Message Definitions of Status Registers Specified by IEEE488.2 Status Registers Specified by IEEE488.2Definition Logical or Bit Status Byte Register Definition Definition of Status Byte Register BitDefinition of Standard Event Status Register Bit Bit Standard Event Status Register Definition Status Register Specified by Scpi To the status Byte register BitDefinition Status Register Specific to MP1777A Status Register Specific to MP1777AINSTrument Status register To the OPERation Reading, Writing and Clearing Status Registers Reading and writing methodsWriting Methods Clearing and Resetting Methods of Status Registers Reset ValueReaister Status Report Scpi Outline Scpi Outline Outline Example of Scpi Command Tree Command StructureSOURce TELecom BRATe Brate BRATe? EQUAlizer EQUAlizer? Commandformat Command Description MethodSCPl Outline Form of header abbreviation Compounding Commands Details of Parameter Type Parameter T V D ~ Scpi Outline INSTrument Subsystem Device Message Details Device Message Details Response FormatResponse Format By Response Type Format Response Format Details of Response Format Buffer Size Stipulations Program command U14 Device Message Details Program Query Command INSTrument COUPle mode Device-Specific CommandsCOUPle ALL ............. Tx&Rx Same SOURce Subsystem M6138 M5156SOURce TELecom BRATe? Device Message Details SOURce TELecom EQUAlizer boolean SOURce TELecom EQUAlizer?SOURce TELecom CLOCk SOURce csource Device-Specific Commands SOURce TELecom CLOCk SOURce? SOURce TELecom JlTTer booleanSOURce TELecom JITTer? SOURce TELecom OFFSet? Device Message Details SOURce TELecom OFFSet numericSOURce JITTer RANGe range UI800 Bit Rate UI Ranae SUORce JlTTer AMPLitude? SENSe Subsystem SENSe TELecom BRATe? SENSe TELecom RANGe range SENSe TELecom RANGe?SENSe TELecom FlLTer filter SENSe TELecom MEASure Type mmode Device-Specific Commands SENSe TELecom FILTer?REPeat SENSe TELecom MEASure TYPE? SENSe TELecom MEASure PERiod? Device-Specific Commands SENSe MEASure STATe? SENSe MEASure STARtSENSe MEASure Stop Device Message Details SENSe MEASure STIMe? DlSPlay DSELect NAME? DlSPlay DSELect Name display DlSPlay SETup Name sdisplay DlSPlay SETup NAME?DlSPlay RESult JITTer Mode mode Device-Specific Commands DlSPlay RESult JlTTer MODE? DlSPlay RESult JlTTer Unit unitDlSPlay RESult JlTTer UNIT? CALCulate DATA? CALCulate DATA? stringString Response Format Jitter manual measurement SYSTem MEMory STORe numeric SYSTem MEMory RECall numeric Device Message Details SYSTern MEMory CLEar numeric SYSTern MEMory LABel numeric, titleSYSTern MEMory LABel? numeric SYSTem DATE? SYSTem Date numericl, numeric2, ~numeric3rSYSTem Time numericl, numeric2, nurneric3 SYSTem TIME? Device Message Details SYSTern BUZZer boolean SYSTern ERRor?SYSTem BUZZer? SYSTern VERSion? STATus OPERation EVENt? STATus PRESet STATus OPERation ENABle numeric STATus OPERation ENABle?Device Message Details STATus OPERation CONDition? Status OPERation NTRansition numeric STATus OPERation PTRansition? Device Message Details STATus OPERation NTRansition? STATus OPERation INSTrument EVENt?STATus OPERation INSTrument CONDition? STATus OPERation INSTrument ENABle numeric STATus OPERation INSTrument ENABle?Status OPERation INSTrument PTRansition numeric STATus OPERation INSTrument NTRansition? STATUSOPERation INSTrument NTRansition numeric Device-Specific Errors Appendix a Scpi Error Messages Command Errors Code Messaae Error Detection Condition Appendix a SCPl Error Messages Run Time ErrorsTable A-2 Error Messages of Run Time Errors Code Message Error Detection Condition Device-Specific Errors Table A-3 Error Messages of Device-Specific ErrorsCode Message Error Detection Condition Table A-4Error Messages of Query Errors Code Query Errors Appendix B Initializing Bus Appendix B Details of Initialization Command FunctionsTable B-2 Changes in Status of Device by IFC Message IFC Message Changes in Status of Device Lnitializing Message Lnitializing Message Initializing Device Items related to the Power On Status Clear PSC flag Device Status at Power Activation Appendix B Details of Initialization Command Functions Head office address was changed Page Brazil ArgentinaCanada Chile Croatia BulgariaCzech Republic Denmark Egypt CyprusIndonesia Israel Pakistan South AfricaThailand