Attendant Power Phone Mounting Cord Cord Bracket | AT&T 518-455-710

Attendant

Power Phone Mounting

Cord Cord Bracket

1 Make sure the above parts are enclosed. If any parts are missing, call the Helpline at 1 800 628-2888.

2 Set all switches on the back

panel to OFF (up).

3 To wall mount with bracket:

AUsing #10 or smaller screw (wood, sheet metal, or concrete screw, depending on wall surface), attach bracket to wall so that hook end is down. Leave clearances shown above. B Align keyhole opening on bottom of unit with hook on bracket.

C Slide unit over hook, then down to secure it.

4 A Making sure all setup

switches are OFF (up), plug one end of the modular phone cord into the "to line" jack on the back panel of the Attendant.

BPlug the other end of the phone cord into an extension jack on a 206 module (see "Hardware Requirements" on page 2-1).

5

Plug one end of the power cord into the 10VAC power connector on the back of the Attendant. Plug the other end into a 120V AC outlet, preferably the same one to which the system control unit is connected.

The power light goes on. A blinking battery light indicates that announce- ments have not yet been recorded. Once announcements are recorded, the battery light stays off until the battery is fully charged (18 hours). See page 2-7for instructions on recording announcements.

6 Move setup switches 1 and 2 to ON (down). These settings will save recorded announcements and other programming during a power outage.

NOTE:

To install multiple devices at a single AC outlet, use a power strip with a built- in surge protector.

Installation and Programming 2-3

Image 25

AT&T 518-455-710 manual Attendant Power Phone Mounting Cord Cord Bracket

Contents

Partner Plus Warranty Copyright 1991 AT&T All Rights Reserved Issue AprilHow To Comment on This Guide Ordering Information Contents Overview Determining the Call Answering Mode How the Attendant Answers and Transfers Calls An Example Overview Caller Dials a Two-Digit Extension Number Answering an Attendant-Transferred Call Setup Decisions An Introduction Immediate Call Answering Mode Determining the Call Answering Mode Determining the Number of Attendants Required Backup Call Answering Mode Determining the Route Plan Determining Lines the Attendant Will Answer Day G h t Example Route Plan ABC Supermarket Type Factory Description Announcement Setting Factory Settings for Attendant Announcement TimesAllocating Time for Announcements Music-on-Hold Source Answering Machines Example Setups Attendant with Routes and Secondary Destinations Attendant with Routes and Secondary Destinations Programming Attendant SystemAttendant Attendant Used with Answering Machine Attendant System First- and Second-Level Attendants First- and Second-Level Attendants None 2nd-level Attendants Announcements Attendant a N o u n c e m e n t Attendant B Call Answering Mode Testing for Proper Operation Installing the Attendant Programming GuidelinesAttendant Programming System Programming for Attendant Operation Additional Safety Instructions for Installation Personnel Important Safety Instructions Attendant Unit Hardware RequirementsFront Panel Talking Back Panel Installing the Attendant Attendant Power Phone Mounting Cord Cord Bracket Programming Guidelines Using the Programming ChartsIntroduction Commonly Changed Settings Change this See If you want to Setting Attendant Programming To adjust clock for Daylight Saving TimeClock Business Days Reallocating Announcement Lengths Business HoursRecording Announcements Answer Delay Night Answer Delay DayRoutes Automatic Tries to Route 0 Night Automatic Tries to Route 0 DaySecurity Code To change the security code System Programming for Attendant Operation Call Answering ModeAttendant Extensions Attendant Line Assignments Transfer Return Extensions Night Service GroupTransfer Return Rings Ensuring Attendant Extensions Are Not in the Calling Group Testing Secondary Destinations Testing Basic Operation Planning Form Attendant in Night Service Group Call Answering ModeAnswer Delay Attendant Extension Day Standard Announcement If Your Announcement Is DifferentNight Transfer Business Schedule System Programming Announcements National Service Assistance Center Helpline 1 800 Power Failure Number Solution Blinks Problem Out-of-Service CodesTable B-1 Out-of-Service Codes Invalid Extensions and Routes Caller Hears Initial Announcement More Than Once Attendant Disconnects Callers After They Select Routes Weight DimensionsBattery System Visual Indicators Power FailureOperation Telephone Line Index IN-I Index IN-2 Index Comcode 106 449 AT&T